lkml.org 
[lkml]   [2022]   [Apr]   [10]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v4 RESEND 8/9] serial: fsl_lpuart: remove redundant code in rs485_config functions
Date
In uart_set_rs485_config() the serial core already ensures that only one of
both options RTS on send or RTS after send is set. It also assigns the
passed serial_rs485 struct to the uart port.

So remove the check and the assignment from the drivers rs485_config()
function to avoid redundancy.

Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
---
drivers/tty/serial/fsl_lpuart.c | 32 --------------------------------
1 file changed, 32 deletions(-)

diff --git a/drivers/tty/serial/fsl_lpuart.c b/drivers/tty/serial/fsl_lpuart.c
index 87789872f400..8fea7fd915d2 100644
--- a/drivers/tty/serial/fsl_lpuart.c
+++ b/drivers/tty/serial/fsl_lpuart.c
@@ -1377,19 +1377,6 @@ static int lpuart_config_rs485(struct uart_port *port,
/* Enable auto RS-485 RTS mode */
modem |= UARTMODEM_TXRTSE;

- /*
- * RTS needs to be logic HIGH either during transfer _or_ after
- * transfer, other variants are not supported by the hardware.
- */
-
- if (!(rs485->flags & (SER_RS485_RTS_ON_SEND |
- SER_RS485_RTS_AFTER_SEND)))
- rs485->flags |= SER_RS485_RTS_ON_SEND;
-
- if (rs485->flags & SER_RS485_RTS_ON_SEND &&
- rs485->flags & SER_RS485_RTS_AFTER_SEND)
- rs485->flags &= ~SER_RS485_RTS_AFTER_SEND;
-
/*
* The hardware defaults to RTS logic HIGH while transfer.
* Switch polarity in case RTS shall be logic HIGH
@@ -1402,9 +1389,6 @@ static int lpuart_config_rs485(struct uart_port *port,
modem |= UARTMODEM_TXRTSPOL;
}

- /* Store the new configuration */
- sport->port.rs485 = *rs485;
-
writeb(modem, sport->port.membase + UARTMODEM);
return 0;
}
@@ -1428,19 +1412,6 @@ static int lpuart32_config_rs485(struct uart_port *port,
/* Enable auto RS-485 RTS mode */
modem |= UARTMODEM_TXRTSE;

- /*
- * RTS needs to be logic HIGH either during transfer _or_ after
- * transfer, other variants are not supported by the hardware.
- */
-
- if (!(rs485->flags & (SER_RS485_RTS_ON_SEND |
- SER_RS485_RTS_AFTER_SEND)))
- rs485->flags |= SER_RS485_RTS_ON_SEND;
-
- if (rs485->flags & SER_RS485_RTS_ON_SEND &&
- rs485->flags & SER_RS485_RTS_AFTER_SEND)
- rs485->flags &= ~SER_RS485_RTS_AFTER_SEND;
-
/*
* The hardware defaults to RTS logic HIGH while transfer.
* Switch polarity in case RTS shall be logic HIGH
@@ -1453,9 +1424,6 @@ static int lpuart32_config_rs485(struct uart_port *port,
modem |= UARTMODEM_TXRTSPOL;
}

- /* Store the new configuration */
- sport->port.rs485 = *rs485;
-
lpuart32_write(&sport->port, modem, UARTMODIR);
return 0;
}
--
2.35.1
\
 
 \ /
  Last update: 2022-04-10 12:48    [W:0.174 / U:0.008 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site