lkml.org 
[lkml]   [2021]   [Mar]   [10]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH net] net: dsa: mt7530: setup core clock even in TRGMII mode
Date
A recent change to MIPS ralink reset logic made it so mt7530 actually
resets the switch on platforms such as mt7621 (where bit 2 is the reset
line for the switch). That exposed an issue where the switch would not
function properly in TRGMII mode after a reset.

Reconfigure core clock in TRGMII mode to fix the issue.

Tested on Ubiquiti ER-X (MT7621) with TRGMII mode enabled.

Fixes: 3f9ef7785a9c ("MIPS: ralink: manage low reset lines")
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
---
drivers/net/dsa/mt7530.c | 52 +++++++++++++++++++---------------------
1 file changed, 25 insertions(+), 27 deletions(-)

diff --git a/drivers/net/dsa/mt7530.c b/drivers/net/dsa/mt7530.c
index f06f5fa2f898..9871d7cff93a 100644
--- a/drivers/net/dsa/mt7530.c
+++ b/drivers/net/dsa/mt7530.c
@@ -436,34 +436,32 @@ mt7530_pad_clk_setup(struct dsa_switch *ds, phy_interface_t interface)
TD_DM_DRVP(8) | TD_DM_DRVN(8));

/* Setup core clock for MT7530 */
- if (!trgint) {
- /* Disable MT7530 core clock */
- core_clear(priv, CORE_TRGMII_GSW_CLK_CG, REG_GSWCK_EN);
-
- /* Disable PLL, since phy_device has not yet been created
- * provided for phy_[read,write]_mmd_indirect is called, we
- * provide our own core_write_mmd_indirect to complete this
- * function.
- */
- core_write_mmd_indirect(priv,
- CORE_GSWPLL_GRP1,
- MDIO_MMD_VEND2,
- 0);
-
- /* Set core clock into 500Mhz */
- core_write(priv, CORE_GSWPLL_GRP2,
- RG_GSWPLL_POSDIV_500M(1) |
- RG_GSWPLL_FBKDIV_500M(25));
+ /* Disable MT7530 core clock */
+ core_clear(priv, CORE_TRGMII_GSW_CLK_CG, REG_GSWCK_EN);

- /* Enable PLL */
- core_write(priv, CORE_GSWPLL_GRP1,
- RG_GSWPLL_EN_PRE |
- RG_GSWPLL_POSDIV_200M(2) |
- RG_GSWPLL_FBKDIV_200M(32));
-
- /* Enable MT7530 core clock */
- core_set(priv, CORE_TRGMII_GSW_CLK_CG, REG_GSWCK_EN);
- }
+ /* Disable PLL, since phy_device has not yet been created
+ * provided for phy_[read,write]_mmd_indirect is called, we
+ * provide our own core_write_mmd_indirect to complete this
+ * function.
+ */
+ core_write_mmd_indirect(priv,
+ CORE_GSWPLL_GRP1,
+ MDIO_MMD_VEND2,
+ 0);
+
+ /* Set core clock into 500Mhz */
+ core_write(priv, CORE_GSWPLL_GRP2,
+ RG_GSWPLL_POSDIV_500M(1) |
+ RG_GSWPLL_FBKDIV_500M(25));
+
+ /* Enable PLL */
+ core_write(priv, CORE_GSWPLL_GRP1,
+ RG_GSWPLL_EN_PRE |
+ RG_GSWPLL_POSDIV_200M(2) |
+ RG_GSWPLL_FBKDIV_200M(32));
+
+ /* Enable MT7530 core clock */
+ core_set(priv, CORE_TRGMII_GSW_CLK_CG, REG_GSWCK_EN);

/* Setup the MT7530 TRGMII Tx Clock */
core_set(priv, CORE_TRGMII_GSW_CLK_CG, REG_GSWCK_EN);
--
2.30.2
\
 
 \ /
  Last update: 2021-03-11 02:22    [W:0.063 / U:0.772 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site