lkml.org 
[lkml]   [2018]   [Dec]   [21]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH 01/13] clk: qcom: gcc: limit GPLL0_AO_OUT operating frequency
From
Date
Hello,

On 12/21/2018 6:06 PM, Jorge Ramirez wrote:
> On 12/21/18 12:19, Taniya Das wrote:
>>
>>
>> On 12/17/2018 3:16 PM, Jorge Ramirez-Ortiz wrote:
>>> Limit the GPLL0_AO_OUT_MAIN operating frequency as per its hardware
>>> specifications.
>>>
>>> Co-developed-by: Niklas Cassel <niklas.cassel@linaro.org>
>>> Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
>>> Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
>>> ---
>>>   drivers/clk/qcom/gcc-qcs404.c | 6 ++++++
>>>   1 file changed, 6 insertions(+)
>>>
>>> diff --git a/drivers/clk/qcom/gcc-qcs404.c
>>> b/drivers/clk/qcom/gcc-qcs404.c
>>> index 64da032..833436a 100644
>>> --- a/drivers/clk/qcom/gcc-qcs404.c
>>> +++ b/drivers/clk/qcom/gcc-qcs404.c
>>> @@ -304,10 +304,16 @@ static struct clk_alpha_pll gpll0_out_main = {
>>>       },
>>>   };
>>>   +static const struct pll_vco gpll0_ao_out_vco[] = {
>>> +    { 800000000, 800000000, 0 },
>>> +};
>>> +
>>>   static struct clk_alpha_pll gpll0_ao_out_main = {
>>>       .offset = 0x21000,
>>>       .regs = clk_alpha_pll_regs[CLK_ALPHA_PLL_TYPE_DEFAULT],
>>>       .flags = SUPPORTS_FSM_MODE,
>>> +    .vco_table = gpll0_ao_out_vco,
>>> +    .num_vco = ARRAY_SIZE(gpll0_ao_out_vco),
>>
>> Could you please help as to why this is required? This is a fixed PLL
>> and we do not require a VCO table for it.
>
> Hi Taniya,
>
> this patch - the additional information that it provides about the
> hardware - helps to select the right parent clock for a given frequency.
>
> On the qcs404 this clock is one of the two parent clocks of the apcs
> clock controller (the other one being the high frequency pll)
> When cpufreq sets a target frequency, there is an iteration through the
> list of parents to select the one that delivers the best match.
>
> When attempting to set the clock for an alpha_pll, the operation does a
> sanity check to validate that the requested frequency is in fact
> reachable using the vco range: trying to set a value that is not in
> range will fail.
>
> This patch makes sure that its range is explicitly defined.
>
> It also helps making sure there are no rounding issues when setting its
> value: without it the clock was being read at 799MHz
>
>

If the PLL is being read as 799MHz it would because not all the 40 bits
of the ALPHA_VAL being programmed by the bootloaders(which are the
original owners of this PLL). So we should go with the way they are
being set by bootloaders and read by HLOS driver.

And a VCO range you have considered is wrong from a PLL perspective. As
these are fixed PLLs and VCO range really does not matter here, so
please drop this change.

>>
>>>       .clkr = {
>>>           .enable_reg = 0x45000,
>>>           .enable_mask = BIT(0),
>>>
>>
>

--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation.

--

\
 
 \ /
  Last update: 2018-12-21 19:00    [W:0.920 / U:0.000 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site