lkml.org 
[lkml]   [2018]   [Dec]   [21]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 01/13] clk: qcom: gcc: limit GPLL0_AO_OUT operating frequency
On Fri 21 Dec 09:58 PST 2018, Taniya Das wrote:

> Hello,
>
> On 12/21/2018 6:06 PM, Jorge Ramirez wrote:
> > On 12/21/18 12:19, Taniya Das wrote:
> > >
> > >
> > > On 12/17/2018 3:16 PM, Jorge Ramirez-Ortiz wrote:
> > > > Limit the GPLL0_AO_OUT_MAIN operating frequency as per its hardware
> > > > specifications.
> > > >
> > > > Co-developed-by: Niklas Cassel <niklas.cassel@linaro.org>
> > > > Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
> > > > Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
> > > > ---
> > > >   drivers/clk/qcom/gcc-qcs404.c | 6 ++++++
> > > >   1 file changed, 6 insertions(+)
> > > >
> > > > diff --git a/drivers/clk/qcom/gcc-qcs404.c
> > > > b/drivers/clk/qcom/gcc-qcs404.c
> > > > index 64da032..833436a 100644
> > > > --- a/drivers/clk/qcom/gcc-qcs404.c
> > > > +++ b/drivers/clk/qcom/gcc-qcs404.c
> > > > @@ -304,10 +304,16 @@ static struct clk_alpha_pll gpll0_out_main = {
> > > >       },
> > > >   };
> > > >   +static const struct pll_vco gpll0_ao_out_vco[] = {
> > > > +    { 800000000, 800000000, 0 },
> > > > +};
> > > > +
> > > >   static struct clk_alpha_pll gpll0_ao_out_main = {
> > > >       .offset = 0x21000,
> > > >       .regs = clk_alpha_pll_regs[CLK_ALPHA_PLL_TYPE_DEFAULT],
> > > >       .flags = SUPPORTS_FSM_MODE,
> > > > +    .vco_table = gpll0_ao_out_vco,
> > > > +    .num_vco = ARRAY_SIZE(gpll0_ao_out_vco),
> > >
> > > Could you please help as to why this is required? This is a fixed
> > > PLL and we do not require a VCO table for it.
> >
> > Hi Taniya,
> >
> > this patch - the additional information that it provides about the
> > hardware - helps to select the right parent clock for a given frequency.
> >
> > On the qcs404 this clock is one of the two parent clocks of the apcs
> > clock controller (the other one being the high frequency pll)
> > When cpufreq sets a target frequency, there is an iteration through the
> > list of parents to select the one that delivers the best match.
> >
> > When attempting to set the clock for an alpha_pll, the operation does a
> > sanity check to validate that the requested frequency is in fact
> > reachable using the vco range: trying to set a value that is not in
> > range will fail.
> >
> > This patch makes sure that its range is explicitly defined.
> >
> > It also helps making sure there are no rounding issues when setting its
> > value: without it the clock was being read at 799MHz
> >
> >
>
> If the PLL is being read as 799MHz it would because not all the 40 bits of
> the ALPHA_VAL being programmed by the bootloaders(which are the original
> owners of this PLL). So we should go with the way they are being set by
> bootloaders and read by HLOS driver.
>
> And a VCO range you have considered is wrong from a PLL perspective. As
> these are fixed PLLs and VCO range really does not matter here, so please
> drop this change.
>

The problem here is that the PLL should be fixed at 800MHz, but the
alpha PLL is defined such that it can change. So when the mux-div is
looking for a suitable parent and divider for our CPU clock it concludes
that the best way to reach certain frequencies is to change the rate of
GPLL0.

Adding the vco_table limits the available frequencies for GPLL0 in
QCS404, without modifying the implementation of the alpha PLL.

Perhaps there's a better way to define that this particular clock
hardware can change rate, but in this implementation it must not?

Regards,
Bjorn

\
 
 \ /
  Last update: 2018-12-21 20:28    [W:0.118 / U:0.000 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site