lkml.org 
[lkml]   [2014]   [Nov]   [23]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCH v3 2/3] ACPI / PMIC: support PMIC operation region for XPower AXP288
Date
On Friday, November 21, 2014 03:11:50 PM Aaron Lu wrote:
> The Baytrail-T-CR platform firmware has defined two customized operation
> regions for PMIC chip Dollar Cove XPower - one is for power resource
> handling and one is for thermal just like the CrystalCove one. This patch
> adds support for them on top of the common PMIC opregion region code.
>
> Signed-off-by: Aaron Lu <aaron.lu@intel.com>
> Acked-by: Lee Jones <lee.jones@linaro.org> for the MFD part
> ---
> drivers/acpi/Kconfig | 6 +
> drivers/acpi/Makefile | 1 +
> drivers/acpi/pmic/intel_pmic_xpower.c | 277 ++++++++++++++++++++++++++++++++++
> drivers/mfd/axp20x.c | 3 +
> 4 files changed, 287 insertions(+)
> create mode 100644 drivers/acpi/pmic/intel_pmic_xpower.c
>
> diff --git a/drivers/acpi/Kconfig b/drivers/acpi/Kconfig
> index 3e5f2056f946..227f0692cbff 100644
> --- a/drivers/acpi/Kconfig
> +++ b/drivers/acpi/Kconfig
> @@ -408,6 +408,12 @@ config CRC_PMIC_OPREGION
> help
> This config adds ACPI operation region support for CrystalCove PMIC.
>
> +config XPOWER_PMIC_OPREGION
> + bool "ACPI operation region support for XPower AXP288 PMIC"
> + depends on AXP288_ADC
> + help
> + This config adds ACPI operation region support for XPower AXP288 PMIC.
> +
> endif
>
> endif # ACPI
> diff --git a/drivers/acpi/Makefile b/drivers/acpi/Makefile
> index f5938399ac14..f74317cc1ca9 100644
> --- a/drivers/acpi/Makefile
> +++ b/drivers/acpi/Makefile
> @@ -91,3 +91,4 @@ obj-$(CONFIG_ACPI_EXTLOG) += acpi_extlog.o
>
> obj-$(CONFIG_PMIC_OPREGION) += pmic/intel_pmic.o
> obj-$(CONFIG_CRC_PMIC_OPREGION) += pmic/intel_pmic_crc.o
> +obj-$(CONFIG_XPOWER_PMIC_OPREGION) += pmic/intel_pmic_xpower.o
> diff --git a/drivers/acpi/pmic/intel_pmic_xpower.c b/drivers/acpi/pmic/intel_pmic_xpower.c
> new file mode 100644
> index 000000000000..6c4d6ce0cff1
> --- /dev/null
> +++ b/drivers/acpi/pmic/intel_pmic_xpower.c
> @@ -0,0 +1,277 @@
> +/*
> + * intel_pmic_xpower.c - XPower AXP288 PMIC operation region driver
> + *
> + * Copyright (C) 2014 Intel Corporation. All rights reserved.
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License version
> + * 2 as published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +#include <linux/module.h>
> +#include <linux/acpi.h>
> +#include <linux/mfd/axp20x.h>
> +#include <linux/regmap.h>
> +#include <linux/platform_device.h>
> +#include <linux/iio/consumer.h>
> +#include "intel_pmic.h"
> +
> +#define XPOWER_GPADC_LOW 0x5b
> +
> +static struct pmic_pwr_table pwr_table[] = {
> + {
> + .address = 0x00,
> + .pwr_reg = {
> + .reg = 0x13,
> + .bit = 0x05,
> + }
> + }, /* ALD1, 0x13, bit5 */

It is not necessary to repeat the reg numbers and bits in the comments.

> + {
> + .address = 0x04,
> + .pwr_reg = {
> + .reg = 0x13,
> + .bit = 0x06,
> + }
> + }, /* ALD2, 0x13, bit6 */
> + {
> + .address = 0x08,
> + .pwr_reg = {
> + .reg = 0x13,
> + .bit = 0x07,
> + }
> + }, /* ALD3, 0x13, bit7 */
> + {
> + .address = 0x0c,
> + .pwr_reg = {
> + .reg = 0x12,
> + .bit = 0x03,
> + }
> + }, /* DLD1, 0x12, bit3 */
> + {
> + .address = 0x10,
> + .pwr_reg = {
> + .reg = 0x12,
> + .bit = 0x04,
> + }
> + }, /* DLD2, 0x12, bit4 */
> + {
> + .address = 0x14,
> + .pwr_reg = {
> + .reg = 0x12,
> + .bit = 0x05,
> + }
> + }, /* DLD3, 0x12, bit5 */
> + {
> + .address = 0x18,
> + .pwr_reg = {
> + .reg = 0x12,
> + .bit = 0x06,
> + }
> + }, /* DLD4, 0x12, bit6 */
> + {
> + .address = 0x1c,
> + .pwr_reg = {
> + .reg = 0x12,
> + .bit = 0x00,
> + }
> + }, /* ELD1, 0x12, bit0 */
> + {
> + .address = 0x20,
> + .pwr_reg = {
> + .reg = 0x12,
> + .bit = 0x01,
> + }
> + }, /* ELD2, 0x12, bit1 */
> + {
> + .address = 0x24,
> + .pwr_reg = {
> + .reg = 0x12,
> + .bit = 0x02,
> + }
> + }, /* ELD3, 0x12, bit2 */
> + {
> + .address = 0x28,
> + .pwr_reg = {
> + .reg = 0x13,
> + .bit = 0x02,
> + }
> + }, /* FLD1, 0x13, bit2 */
> + {
> + .address = 0x2c,
> + .pwr_reg = {
> + .reg = 0x13,
> + .bit = 0x03,
> + }
> + }, /* FLD2, 0x13, bit3 */
> + {
> + .address = 0x30,
> + .pwr_reg = {
> + .reg = 0x13,
> + .bit = 0x04,
> + }
> + }, /* FLD3, 0x13, bit4 */
> + {
> + .address = 0x38,
> + .pwr_reg = {
> + .reg = 0x10,
> + .bit = 0x03,
> + }
> + }, /* BUC1, 0x10, bit3 */
> + {
> + .address = 0x3c,
> + .pwr_reg = {
> + .reg = 0x10,
> + .bit = 0x06,
> + }
> + }, /* BUC2, 0x10, bit6 */
> + {
> + .address = 0x40,
> + .pwr_reg = {
> + .reg = 0x10,
> + .bit = 0x05,
> + }
> + }, /* BUC3, 0x10, bit5 */
> + {
> + .address = 0x44,
> + .pwr_reg = {
> + .reg = 0x10,
> + .bit = 0x04,
> + }
> + }, /* BUC4, 0x10, bit4 */
> + {
> + .address = 0x48,
> + .pwr_reg = {
> + .reg = 0x10,
> + .bit = 0x01,
> + }
> + }, /* BUC5, 0x10, bit1 */
> + {
> + .address = 0x4c,
> + .pwr_reg = {
> + .reg = 0x10,
> + .bit = 0x00
> + }
> + }, /* BUC6, 0x10, bit0 */
> +};
> +
> +/* TMP0 - TMP5 are the same, all from GPADC */
> +static struct pmic_thermal_table thermal_table[] = {
> + {
> + .address = 0x00,
> + .reg = XPOWER_GPADC_LOW
> + },
> + {
> + .address = 0x0c,
> + .reg = XPOWER_GPADC_LOW
> + },
> + {
> + .address = 0x18,
> + .reg = XPOWER_GPADC_LOW
> + },
> + {
> + .address = 0x24,
> + .reg = XPOWER_GPADC_LOW
> + },
> + {
> + .address = 0x30,
> + .reg = XPOWER_GPADC_LOW
> + },
> + {
> + .address = 0x3c,
> + .reg = XPOWER_GPADC_LOW
> + },
> +};
> +
> +static int intel_xpower_pmic_get_power(struct regmap *regmap,
> + struct pmic_pwr_reg *preg, u64 *value)
> +{
> + int data;
> +
> + if (regmap_read(regmap, preg->reg, &data))
> + return -EIO;
> +
> + *value = (data & BIT(preg->bit)) ? 1 : 0;
> + return 0;
> +}
> +
> +static int intel_xpower_pmic_update_power(struct regmap *regmap,
> + struct pmic_pwr_reg *preg, bool on)
> +{
> + int data;
> +
> + if (regmap_read(regmap, preg->reg, &data))
> + return -EIO;
> +
> + if (on)
> + data |= BIT(preg->bit);
> + else
> + data &= ~BIT(preg->bit);
> +
> + if (regmap_write(regmap, preg->reg, data))
> + return -EIO;
> +
> + return 0;
> +}
> +
> +/*
> + * We could get the sensor value by manipulating the HW regs here, but since
> + * the axp288 IIO driver may also access the same regs at the same time, the
> + * APIs provided by IIO subsystem are used here instead to avoid problems. As
> + * a result, the two passed in params are of no actual use.
> + */
> +static int intel_xpower_pmic_get_raw_temp(struct regmap *regmap, int reg)
> +{
> + struct iio_channel *gpadc_chan;
> + int ret, val;
> +
> + gpadc_chan = iio_channel_get(NULL, "axp288-system-temp");
> + if (IS_ERR_OR_NULL(gpadc_chan))
> + return -EACCES;
> +
> + ret = iio_read_channel_raw(gpadc_chan, &val);
> + if (ret < 0)
> + val = ret;
> +
> + iio_channel_release(gpadc_chan);
> + return val;
> +}
> +
> +static struct intel_pmic_opregion_data intel_xpower_pmic_opregion_data = {
> + .get_power = intel_xpower_pmic_get_power,
> + .update_power = intel_xpower_pmic_update_power,
> + .get_raw_temp = intel_xpower_pmic_get_raw_temp,
> + .pwr_table = pwr_table,
> + .pwr_table_count = ARRAY_SIZE(pwr_table),
> + .thermal_table = thermal_table,
> + .thermal_table_count = ARRAY_SIZE(thermal_table),
> +};
> +
> +
> +static int intel_xpower_pmic_opregion_probe(struct platform_device *pdev)
> +{
> + struct axp20x_dev *axp20x = dev_get_drvdata(pdev->dev.parent);
> + return intel_pmic_install_opregion_handler(&pdev->dev,
> + ACPI_HANDLE(pdev->dev.parent), axp20x->regmap,
> + &intel_xpower_pmic_opregion_data);
> +}
> +
> +static struct platform_driver intel_xpower_pmic_opregion_driver = {
> + .probe = intel_xpower_pmic_opregion_probe,
> + .driver = {
> + .name = "axp288_opregion",
> + },
> +};
> +
> +static int __init intel_xpower_pmic_opregion_driver_init(void)
> +{
> + return platform_driver_register(&intel_xpower_pmic_opregion_driver);
> +}
> +module_init(intel_xpower_pmic_opregion_driver_init);
> +
> +MODULE_DESCRIPTION("XPower AXP288 ACPI operation region driver");
> +MODULE_LICENSE("GPL");
> diff --git a/drivers/mfd/axp20x.c b/drivers/mfd/axp20x.c
> index acbb4c3bf98c..daf3c8d33b4d 100644
> --- a/drivers/mfd/axp20x.c
> +++ b/drivers/mfd/axp20x.c
> @@ -354,6 +354,9 @@ static struct mfd_cell axp288_cells[] = {
> .num_resources = ARRAY_SIZE(axp288_battery_resources),
> .resources = axp288_battery_resources,
> },
> + {
> + .name = "axp288_opregion",
> + },
> };
>
> static struct axp20x_dev *axp20x_pm_power_off;
>

The rest looks OK to me.

--
I speak only for myself.
Rafael J. Wysocki, Intel Open Source Technology Center.


\
 
 \ /
  Last update: 2014-11-24 02:21    [W:2.214 / U:0.108 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site