lkml.org 
[lkml]   [2013]   [Sep]   [26]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH] i2c-designware: 10-bit addressing mode enabling if I2C_DYNAMIC_TAR_UPDATE is set.
Date
According to Designware I2C spec, if I2C_DYNAMIC_TAR_UPDATE is set to 1,
the 10-bit addressing mode is controlled by IC_10BITADDR_MASTER bit of
IC_TAR register instead of IC_CON register. The IC_10BITADDR_MASTER
in IC_CON register becomes read-only copy. Since I2C_DYNAMIC_TAR_UPDATE
value can't be detected from hardware register, so we will always set the
IC_10BITADDR_MASTER bit in both IC_CON and IC_TAR register whenever 10-bit
addresing mode is requested by user application.

Signed-off-by: Chew, Chiau Ee <chiau.ee.chew@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
---
drivers/i2c/busses/i2c-designware-core.c | 26 ++++++++++++++++++++------
1 files changed, 20 insertions(+), 6 deletions(-)

diff --git a/drivers/i2c/busses/i2c-designware-core.c b/drivers/i2c/busses/i2c-designware-core.c
index dbecf08..5888fee 100644
--- a/drivers/i2c/busses/i2c-designware-core.c
+++ b/drivers/i2c/busses/i2c-designware-core.c
@@ -98,6 +98,8 @@

#define DW_IC_ERR_TX_ABRT 0x1

+#define DW_IC_TAR_10BITADDR_MASTER BIT(12)
+
/*
* status codes
*/
@@ -388,22 +390,34 @@ static int i2c_dw_wait_bus_not_busy(struct dw_i2c_dev *dev)
static void i2c_dw_xfer_init(struct dw_i2c_dev *dev)
{
struct i2c_msg *msgs = dev->msgs;
- u32 ic_con;
+ u32 ic_con, ic_tar = 0;

/* Disable the adapter */
__i2c_dw_enable(dev, false);

- /* set the slave (target) address */
- dw_writel(dev, msgs[dev->msg_write_idx].addr, DW_IC_TAR);
-
/* if the slave address is ten bit address, enable 10BITADDR */
ic_con = dw_readl(dev, DW_IC_CON);
- if (msgs[dev->msg_write_idx].flags & I2C_M_TEN)
+ if (msgs[dev->msg_write_idx].flags & I2C_M_TEN) {
ic_con |= DW_IC_CON_10BITADDR_MASTER;
- else
+ /*
+ * If I2C_DYNAMIC_TAR_UPDATE is set, the 10-bit addressing
+ * mode has to be enabled via bit 12 of IC_TAR register.
+ * We set it always as I2C_DYNAMIC_TAR_UPDATE can't be
+ * detected from registers.
+ */
+ ic_tar = DW_IC_TAR_10BITADDR_MASTER;
+ } else {
ic_con &= ~DW_IC_CON_10BITADDR_MASTER;
+ }
+
dw_writel(dev, ic_con, DW_IC_CON);

+ /*
+ * Set the slave (target) address and enable 10-bit addressing mode
+ * if applicable.
+ */
+ dw_writel(dev, msgs[dev->msg_write_idx].addr | ic_tar, DW_IC_TAR);
+
/* Enable the adapter */
__i2c_dw_enable(dev, true);

--
1.7.4.4


\
 
 \ /
  Last update: 2013-09-26 13:01    [W:0.059 / U:0.220 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site