lkml.org 
[lkml]   [2024]   [Apr]   [17]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH] ASoC: dt-bindings: fsl,ssi: Convert to YAML
Date
Convert the fsl,ssi binding to YAML.

Add below compatible strings which were not listed
in document:

fsl,imx50-ssi
fsl,imx53-ssi
fsl,imx25-ssi
fsl,imx27-ssi
fsl,imx6q-ssi
fsl,imx6sl-ssi
fsl,imx6sx-ssi

Add below fsl,mode strings which were not listed.

i2s-slave
i2s-master
lj-slave
lj-master
rj-slave
rj-master

Then dtbs_check can pass.

And remove the 'codec' description which should be
in 'codec' binding doc.

Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
---
.../devicetree/bindings/sound/fsl,ssi.txt | 87 --------
.../devicetree/bindings/sound/fsl,ssi.yaml | 186 ++++++++++++++++++
2 files changed, 186 insertions(+), 87 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/sound/fsl,ssi.txt
create mode 100644 Documentation/devicetree/bindings/sound/fsl,ssi.yaml

diff --git a/Documentation/devicetree/bindings/sound/fsl,ssi.txt b/Documentation/devicetree/bindings/sound/fsl,ssi.txt
deleted file mode 100644
index 7e15a85cecd2..000000000000
--- a/Documentation/devicetree/bindings/sound/fsl,ssi.txt
+++ /dev/null
@@ -1,87 +0,0 @@
-Freescale Synchronous Serial Interface
-
-The SSI is a serial device that communicates with audio codecs. It can
-be programmed in AC97, I2S, left-justified, or right-justified modes.
-
-Required properties:
-- compatible: Compatible list, should contain one of the following
- compatibles:
- fsl,mpc8610-ssi
- fsl,imx51-ssi
- fsl,imx35-ssi
- fsl,imx21-ssi
-- cell-index: The SSI, <0> = SSI1, <1> = SSI2, and so on.
-- reg: Offset and length of the register set for the device.
-- interrupts: <a b> where a is the interrupt number and b is a
- field that represents an encoding of the sense and
- level information for the interrupt. This should be
- encoded based on the information in section 2)
- depending on the type of interrupt controller you
- have.
-- fsl,fifo-depth: The number of elements in the transmit and receive FIFOs.
- This number is the maximum allowed value for SFCSR[TFWM0].
- - clocks: "ipg" - Required clock for the SSI unit
- "baud" - Required clock for SSI master mode. Otherwise this
- clock is not used
-
-Required are also ac97 link bindings if ac97 is used. See
-Documentation/devicetree/bindings/sound/soc-ac97link.txt for the necessary
-bindings.
-
-Optional properties:
-- codec-handle: Phandle to a 'codec' node that defines an audio
- codec connected to this SSI. This node is typically
- a child of an I2C or other control node.
-- fsl,fiq-stream-filter: Bool property. Disabled DMA and use FIQ instead to
- filter the codec stream. This is necessary for some boards
- where an incompatible codec is connected to this SSI, e.g.
- on pca100 and pcm043.
-- dmas: Generic dma devicetree binding as described in
- Documentation/devicetree/bindings/dma/dma.txt.
-- dma-names: Two dmas have to be defined, "tx" and "rx", if fsl,imx-fiq
- is not defined.
-- fsl,mode: The operating mode for the AC97 interface only.
- "ac97-slave" - AC97 mode, SSI is clock slave
- "ac97-master" - AC97 mode, SSI is clock master
-- fsl,ssi-asynchronous:
- If specified, the SSI is to be programmed in asynchronous
- mode. In this mode, pins SRCK, STCK, SRFS, and STFS must
- all be connected to valid signals. In synchronous mode,
- SRCK and SRFS are ignored. Asynchronous mode allows
- playback and capture to use different sample sizes and
- sample rates. Some drivers may require that SRCK and STCK
- be connected together, and SRFS and STFS be connected
- together. This would still allow different sample sizes,
- but not different sample rates.
-- fsl,playback-dma: Phandle to a node for the DMA channel to use for
- playback of audio. This is typically dictated by SOC
- design. See the notes below.
- Only used on Power Architecture.
-- fsl,capture-dma: Phandle to a node for the DMA channel to use for
- capture (recording) of audio. This is typically dictated
- by SOC design. See the notes below.
- Only used on Power Architecture.
-
-Child 'codec' node required properties:
-- compatible: Compatible list, contains the name of the codec
-
-Child 'codec' node optional properties:
-- clock-frequency: The frequency of the input clock, which typically comes
- from an on-board dedicated oscillator.
-
-Notes on fsl,playback-dma and fsl,capture-dma:
-
-On SOCs that have an SSI, specific DMA channels are hard-wired for playback
-and capture. On the MPC8610, for example, SSI1 must use DMA channel 0 for
-playback and DMA channel 1 for capture. SSI2 must use DMA channel 2 for
-playback and DMA channel 3 for capture. The developer can choose which
-DMA controller to use, but the channels themselves are hard-wired. The
-purpose of these two properties is to represent this hardware design.
-
-The device tree nodes for the DMA channels that are referenced by
-"fsl,playback-dma" and "fsl,capture-dma" must be marked as compatible with
-"fsl,ssi-dma-channel". The SOC-specific compatible string (e.g.
-"fsl,mpc8610-dma-channel") can remain. If these nodes are left as
-"fsl,elo-dma-channel" or "fsl,eloplus-dma-channel", then the generic Elo DMA
-drivers (fsldma) will attempt to use them, and it will conflict with the
-sound drivers.
diff --git a/Documentation/devicetree/bindings/sound/fsl,ssi.yaml b/Documentation/devicetree/bindings/sound/fsl,ssi.yaml
new file mode 100644
index 000000000000..bc8daafb7d81
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/fsl,ssi.yaml
@@ -0,0 +1,186 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/sound/fsl,ssi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Freescale Synchronous Serial Interface
+
+maintainers:
+ - Shengjiu Wang <shengjiu.wang@nxp.com>
+
+description:
+ Notes on fsl,playback-dma and fsl,capture-dma
+ On SOCs that have an SSI, specific DMA channels are hard-wired for playback
+ and capture. On the MPC8610, for example, SSI1 must use DMA channel 0 for
+ playback and DMA channel 1 for capture. SSI2 must use DMA channel 2 for
+ playback and DMA channel 3 for capture. The developer can choose which
+ DMA controller to use, but the channels themselves are hard-wired. The
+ purpose of these two properties is to represent this hardware design.
+
+ The device tree nodes for the DMA channels that are referenced by
+ "fsl,playback-dma" and "fsl,capture-dma" must be marked as compatible with
+ "fsl,ssi-dma-channel". The SOC-specific compatible string (e.g.
+ "fsl,mpc8610-dma-channel") can remain. If these nodes are left as
+ "fsl,elo-dma-channel" or "fsl,eloplus-dma-channel", then the generic Elo DMA
+ drivers (fsldma) will attempt to use them, and it will conflict with the
+ sound drivers.
+
+properties:
+ compatible:
+ oneOf:
+ - items:
+ - enum:
+ - fsl,imx50-ssi
+ - fsl,imx53-ssi
+ - enum:
+ - fsl,imx51-ssi
+ - enum:
+ - fsl,imx21-ssi
+ - items:
+ - enum:
+ - fsl,imx25-ssi
+ - fsl,imx27-ssi
+ - fsl,imx35-ssi
+ - fsl,imx51-ssi
+ - fsl,imx6q-ssi
+ - fsl,imx6sl-ssi
+ - fsl,imx6sx-ssi
+ - enum:
+ - fsl,imx21-ssi
+ - fsl,imx51-ssi
+ - items:
+ - const: fsl,mpc8610-ssi
+
+ cell-index:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1, 2]
+ description: The SSI index
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ fsl,fifo-depth:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ The number of elements in the transmit and receive FIFOs.
+ This number is the maximum allowed value for SFCSR[TFWM0].
+
+ clocks:
+ items:
+ - description: The ipg clock for register access
+ - description: clock for SSI master mode
+ minItems: 1
+
+ clock-names:
+ items:
+ - const: ipg
+ - const: baud
+ minItems: 1
+
+ dmas:
+ oneOf:
+ - items:
+ - description: DMA controller phandle and request line for RX
+ - description: DMA controller phandle and request line for TX
+ - items:
+ - description: DMA controller phandle and request line for RX0
+ - description: DMA controller phandle and request line for TX0
+ - description: DMA controller phandle and request line for RX1
+ - description: DMA controller phandle and request line for TX1
+
+ dma-names:
+ oneOf:
+ - items:
+ - const: rx
+ - const: tx
+ - items:
+ - const: rx0
+ - const: tx0
+ - const: rx1
+ - const: tx1
+
+ codec-handle:
+ $ref: /schemas/types.yaml#/definitions/phandle
+ description:
+ Phandle to a 'codec' node that defines an audio
+ codec connected to this SSI. This node is typically
+ a child of an I2C or other control node.
+
+ fsl,fiq-stream-filter:
+ type: boolean
+ description:
+ Disabled DMA and use FIQ instead to filter the codec stream.
+ This is necessary for some boards where an incompatible codec
+ is connected to this SSI, e.g. on pca100 and pcm043.
+
+ fsl,mode:
+ $ref: /schemas/types.yaml#/definitions/string
+ enum: [ ac97-slave, ac97-master, i2s-slave, i2s-master,
+ lj-slave, lj-master, rj-slave, rj-master ]
+ description: |
+ "ac97-slave" - AC97 mode, SSI is clock slave
+ "ac97-master" - AC97 mode, SSI is clock master
+ "i2s-slave" - I2S mode, SSI is clock slave
+ "i2s-master" - I2S mode, SSI is clock master
+ "lj-slave" - Left justified mode, SSI is clock slave
+ "lj-master" - Left justified mode, SSI is clock master
+ "rj-slave" - Right justified mode, SSI is clock slave
+ "rj-master" - Right justified mode, SSI is clock master
+
+ fsl,ssi-asynchronous:
+ type: boolean
+ description: If specified, the SSI is to be programmed in asynchronous
+ mode. In this mode, pins SRCK, STCK, SRFS, and STFS must
+ all be connected to valid signals. In synchronous mode,
+ SRCK and SRFS are ignored. Asynchronous mode allows
+ playback and capture to use different sample sizes and
+ sample rates. Some drivers may require that SRCK and STCK
+ be connected together, and SRFS and STFS be connected
+ together. This would still allow different sample sizes,
+ but not different sample rates.
+
+ fsl,playback-dma:
+ $ref: /schemas/types.yaml#/definitions/phandle
+ description: Phandle to a node for the DMA channel to use for
+ playback of audio. This is typically dictated by SOC
+ design. Only used on Power Architecture.
+
+ fsl,capture-dma:
+ $ref: /schemas/types.yaml#/definitions/phandle
+ description: Phandle to a node for the DMA channel to use for
+ capture (recording) of audio. This is typically dictated
+ by SOC design. Only used on Power Architecture.
+
+ "#sound-dai-cells":
+ const: 0
+ description: optional, some dts node didn't add it.
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - fsl,fifo-depth
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/clock/imx6qdl-clock.h>
+ ssi1: ssi@2028000 {
+ compatible = "fsl,imx6q-ssi",
+ "fsl,imx51-ssi";
+ #sound-dai-cells = <0>;
+ reg = <0x02028000 0x4000>;
+ interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6QDL_CLK_SSI1_IPG>,
+ <&clks IMX6QDL_CLK_SSI1>;
+ clock-names = "ipg", "baud";
+ dmas = <&sdma 37 1 0>, <&sdma 38 1 0>;
+ dma-names = "rx", "tx";
+ fsl,fifo-depth = <15>;
+ };
--
2.34.1

\
 
 \ /
  Last update: 2024-04-17 11:43    [W:0.065 / U:0.188 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site