lkml.org 
[lkml]   [2024]   [Apr]   [17]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [RFC PATCH v2 5/6] watchdog: ROHM BD96801 PMIC WDG driver
On 2024-04-12 at 16:52:46, Matti Vaittinen (mazziesaccount@gmail.com) wrote:
> Introduce driver for WDG block on ROHM BD96801 scalable PMIC.
>
> This driver only supports watchdog with I2C feeding and delayed
> response detection. Whether the watchdog toggles PRSTB pin or
> just causes an interrupt can be configured via device-tree.
>
> The BD96801 PMIC HW supports also window watchdog (too early
> feeding detection) and Q&A mode. These are not supported by
> this driver.
>
> Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
>
> ---
> Revision history:
> RFCv1 => RFCv2:
> - remove always running
> - add IRQ handling
> - call emergency_restart()
> - drop MODULE_ALIAS and add MODULE_DEVICE_TABLE
> ---
> drivers/watchdog/Kconfig | 13 ++
> drivers/watchdog/Makefile | 1 +
> drivers/watchdog/bd96801_wdt.c | 389 +++++++++++++++++++++++++++++++++
> 3 files changed, 403 insertions(+)
> create mode 100644 drivers/watchdog/bd96801_wdt.c
>
> diff --git a/drivers/watchdog/Kconfig b/drivers/watchdog/Kconfig
> index 6bee137cfbe0..d97e735e1faa 100644
> --- a/drivers/watchdog/Kconfig
> +++ b/drivers/watchdog/Kconfig
> @@ -181,6 +181,19 @@ config BD957XMUF_WATCHDOG
> watchdog. Alternatively say M to compile the driver as a module,
> which will be called bd9576_wdt.
>
> +config BD96801_WATCHDOG
> + tristate "ROHM BD96801 PMIC Watchdog"
> + depends on MFD_ROHM_BD96801
> + select WATCHDOG_CORE
> + help
> + Support for the watchdog in the ROHM BD96801 PMIC. Watchdog can be
> + configured to only generate IRQ or to trigger system reset via reset
> + pin.
> +
> + Say Y here to include support for the ROHM BD96801 watchdog.
> + Alternatively say M to compile the driver as a module,
> + which will be called bd96801_wdt.
> +
> config CROS_EC_WATCHDOG
> tristate "ChromeOS EC-based watchdog"
> select WATCHDOG_CORE
> diff --git a/drivers/watchdog/Makefile b/drivers/watchdog/Makefile
> index 3710c218f05e..31bc94436c81 100644
> --- a/drivers/watchdog/Makefile
> +++ b/drivers/watchdog/Makefile
> @@ -217,6 +217,7 @@ obj-$(CONFIG_XEN_WDT) += xen_wdt.o
>
> # Architecture Independent
> obj-$(CONFIG_BD957XMUF_WATCHDOG) += bd9576_wdt.o
> +obj-$(CONFIG_BD96801_WATCHDOG) += bd96801_wdt.o
> obj-$(CONFIG_CROS_EC_WATCHDOG) += cros_ec_wdt.o
> obj-$(CONFIG_DA9052_WATCHDOG) += da9052_wdt.o
> obj-$(CONFIG_DA9055_WATCHDOG) += da9055_wdt.o
> diff --git a/drivers/watchdog/bd96801_wdt.c b/drivers/watchdog/bd96801_wdt.c
> new file mode 100644
> index 000000000000..08fab9a87aec
> --- /dev/null
> +++ b/drivers/watchdog/bd96801_wdt.c
> @@ -0,0 +1,389 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Copyright (C) 2024 ROHM Semiconductors
> + *
> + * ROHM BD96801 watchdog driver
> + */
> +
> +#include <linux/interrupt.h>
> +#include <linux/kernel.h>
> +#include <linux/mfd/rohm-bd96801.h>
> +#include <linux/mfd/rohm-generic.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/platform_device.h>
> +#include <linux/regmap.h>
> +#include <linux/watchdog.h>
> +
> +static bool nowayout;
> +module_param(nowayout, bool, 0);
> +MODULE_PARM_DESC(nowayout,
> + "Watchdog cannot be stopped once started (default=\"false\")");
> +
> +#define BD96801_WD_TMO_SHORT_MASK 0x70
> +#define BD96801_WD_RATIO_MASK 0x3
> +#define BD96801_WD_TYPE_MASK 0x4
> +#define BD96801_WD_TYPE_SLOW 0x4
> +#define BD96801_WD_TYPE_WIN 0x0
> +
> +#define BD96801_WD_EN_MASK 0x3
> +#define BD96801_WD_IF_EN 0x1
> +#define BD96801_WD_QA_EN 0x2
> +#define BD96801_WD_DISABLE 0x0
> +
> +#define BD96801_WD_ASSERT_MASK 0x8
> +#define BD96801_WD_ASSERT_RST 0x8
> +#define BD96801_WD_ASSERT_IRQ 0x0
> +
> +#define BD96801_WD_FEED_MASK 0x1
> +#define BD96801_WD_FEED 0x1
> +
> +/* units in uS */
> +#define FASTNG_MIN 3370
> +#define BD96801_WDT_DEFAULT_MARGIN 6905120
> +/* Unit is seconds */
> +#define DEFAULT_TIMEOUT 30
> +
> +/*
> + * BD96801 WDG supports window mode so the TMO consists of SHORT and LONG
> + * timeout values. SHORT time is meaningfull only in window mode where feeding
> + * period shorter than SHORT would be an error. LONG time is used to detect if
> + * feeding is not occurring within given time limit (SoC SW hangs). The LONG
> + * timeout time is a multiple of (2, 4, 8 0r 16 times) the SHORT timeout.
> + */
> +
> +struct wdtbd96801 {
> + struct device *dev;
> + struct regmap *regmap;
> + struct watchdog_device wdt;
> +};
> +
> +static int bd96801_wdt_ping(struct watchdog_device *wdt)
> +{
> + struct wdtbd96801 *w = watchdog_get_drvdata(wdt);
> +
> + return regmap_update_bits(w->regmap, BD96801_REG_WD_FEED,
> + BD96801_WD_FEED_MASK, BD96801_WD_FEED);
> +}
> +
> +static int bd96801_wdt_start(struct watchdog_device *wdt)
> +{
> + struct wdtbd96801 *w = watchdog_get_drvdata(wdt);
> + int ret;
> +
> + ret = regmap_update_bits(w->regmap, BD96801_REG_WD_CONF,
> + BD96801_WD_EN_MASK, BD96801_WD_IF_EN);
> +
> + return ret;
> +}
> +
> +static int bd96801_wdt_stop(struct watchdog_device *wdt)
> +{
> + struct wdtbd96801 *w = watchdog_get_drvdata(wdt);
> +
> + return regmap_update_bits(w->regmap, BD96801_REG_WD_CONF,
> + BD96801_WD_EN_MASK, BD96801_WD_DISABLE);
> +}
> +
> +static const struct watchdog_info bd96801_wdt_info = {
> + .options = WDIOF_MAGICCLOSE | WDIOF_KEEPALIVEPING |
> + WDIOF_SETTIMEOUT,
> + .identity = "BD96801 Watchdog",
> +};
> +
> +static const struct watchdog_ops bd96801_wdt_ops = {
> + .start = bd96801_wdt_start,
> + .stop = bd96801_wdt_stop,
> + .ping = bd96801_wdt_ping,
> +};
Is there no way to setup a timeout to the WDOG device from userspace?

> +
> +static int find_closest_fast(int target, int *sel, int *val)
> +{
> + int i;
> + int window = FASTNG_MIN;
> +
> + for (i = 0; i < 8 && window < target; i++)
> + window <<= 1;
> +
> + *val = window;
> + *sel = i;
> +
> + if (i == 8)
> + return -EINVAL;
> +
> + return 0;
> +}
> +
> +static int find_closest_slow_by_fast(int fast_val, int *target, int *slowsel)
> +{
> + int sel;
> + static const int multipliers[] = {2, 4, 8, 16};
> +
> + for (sel = 0; sel < ARRAY_SIZE(multipliers) &&
> + multipliers[sel] * fast_val < *target; sel++)
> + ;
> +
> + if (sel == ARRAY_SIZE(multipliers))
> + return -EINVAL;
> +
> + *slowsel = sel;
> + *target = multipliers[sel] * fast_val;
> +
> + return 0;
> +}
> +
> +static int find_closest_slow(int *target, int *slow_sel, int *fast_sel)
> +{
> + static const int multipliers[] = {2, 4, 8, 16};
> + int i, j;
> + int val = 0;
> + int window = FASTNG_MIN;
> +
> + for (i = 0; i < 8; i++) {
> + for (j = 0; j < ARRAY_SIZE(multipliers); j++) {
> + int slow;
> +
> + slow = window * multipliers[j];
> + if (slow >= *target && (!val || slow < val)) {
> + val = slow;
> + *fast_sel = i;
> + *slow_sel = j;
> + }
> + }
> + window <<= 1;
> + }
> + if (!val)
> + return -EINVAL;
> +
> + *target = val;
> +
> + return 0;
> +}
> +
> +static int bd96801_set_wdt_mode(struct wdtbd96801 *w, int hw_margin,
> + int hw_margin_min)
> +{
> + int ret, fastng, slowng, type, reg, mask;
> + struct device *dev = w->dev;
> +
> + /* convert to uS */
> + hw_margin *= 1000;
> + hw_margin_min *= 1000;
> + if (hw_margin_min) {
> + int min;
> +
> + type = BD96801_WD_TYPE_WIN;
> + dev_dbg(dev, "Setting type WINDOW 0x%x\n", type);
> + ret = find_closest_fast(hw_margin_min, &fastng, &min);
> + if (ret) {
> + dev_err(dev, "bad WDT window for fast timeout\n");
> + return ret;
> + }
> +
> + ret = find_closest_slow_by_fast(min, &hw_margin, &slowng);
> + if (ret) {
> + dev_err(dev, "bad WDT window\n");
> + return ret;
> + }
> + w->wdt.min_hw_heartbeat_ms = min / 1000;
> + } else {
> + type = BD96801_WD_TYPE_SLOW;
> + dev_dbg(dev, "Setting type SLOW 0x%x\n", type);
> + ret = find_closest_slow(&hw_margin, &slowng, &fastng);
> + if (ret) {
> + dev_err(dev, "bad WDT window\n");
> + return ret;
> + }
> + }
> +
> + w->wdt.max_hw_heartbeat_ms = hw_margin / 1000;
> +
> + fastng <<= ffs(BD96801_WD_TMO_SHORT_MASK) - 1;
> +
> + reg = slowng | fastng;
> + mask = BD96801_WD_RATIO_MASK | BD96801_WD_TMO_SHORT_MASK;
> + ret = regmap_update_bits(w->regmap, BD96801_REG_WD_TMO,
> + mask, reg);
> + if (ret)
> + return ret;
> +
> + ret = regmap_update_bits(w->regmap, BD96801_REG_WD_CONF,
> + BD96801_WD_TYPE_MASK, type);
> +
> + return ret;
> +}
> +
> +static int bd96801_set_heartbeat_from_hw(struct wdtbd96801 *w,
> + unsigned int conf_reg)
> +{
> + int ret;
> + unsigned int val, sel, fast;
> +
> + /*
> + * The BD96801 supports a somewhat peculiar QA-mode, which we do not
> + * support in this driver. If the QA-mode is enabled then we just
> + * warn and bail-out.
> + */
> + if ((conf_reg & BD96801_WD_EN_MASK) != BD96801_WD_IF_EN) {
> + dev_warn(w->dev, "watchdog set to Q&A mode - exiting\n");
> + return -EINVAL;
> + }
> +
> + ret = regmap_read(w->regmap, BD96801_REG_WD_TMO, &val);
> + if (ret)
> + return ret;
> +
> + sel = val & BD96801_WD_TMO_SHORT_MASK;
> + sel >>= ffs(BD96801_WD_TMO_SHORT_MASK) - 1;
> + fast = FASTNG_MIN << sel;
> +
> + sel = (val & BD96801_WD_RATIO_MASK) + 1;
> + w->wdt.max_hw_heartbeat_ms = (fast << sel) / USEC_PER_MSEC;
> +
> + if ((conf_reg & BD96801_WD_TYPE_MASK) == BD96801_WD_TYPE_WIN)
> + w->wdt.min_hw_heartbeat_ms = fast / USEC_PER_MSEC;
> +
> + return 0;
> +}
> +
> +static int init_wdg_hw(struct wdtbd96801 *w)
> +{
> + u32 hw_margin[2];
> + int count, ret;
> + u32 hw_margin_max = BD96801_WDT_DEFAULT_MARGIN, hw_margin_min = 0;
> +
> + count = device_property_count_u32(w->dev->parent, "rohm,hw-timeout-ms");
Why is that timeout need to be configured from a devicce-tree property?
set_timeout/get_timeout can't be done for this device?

> + if (count < 0 && count != -EINVAL)
> + return count;
> +
> + if (count > 0) {
> + if (count > ARRAY_SIZE(hw_margin))
> + return -EINVAL;
> +
> + ret = device_property_read_u32_array(w->dev->parent,
> + "rohm,hw-timeout-ms",
> + &hw_margin[0], count);
> + if (ret < 0)
> + return ret;
> +
> + if (count == 1)
> + hw_margin_max = hw_margin[0];
> +
> + if (count == 2) {
> + hw_margin_max = hw_margin[1];
> + hw_margin_min = hw_margin[0];
> + }
> + }
> +
> + ret = bd96801_set_wdt_mode(w, hw_margin_max, hw_margin_min);
> + if (ret)
> + return ret;
> +
> + ret = device_property_match_string(w->dev->parent, "rohm,wdg-action",
> + "prstb");
> + if (ret >= 0) {
> + ret = regmap_update_bits(w->regmap, BD96801_REG_WD_CONF,
> + BD96801_WD_ASSERT_MASK,
> + BD96801_WD_ASSERT_RST);
> + return ret;
> + }
> +
> + ret = device_property_match_string(w->dev->parent, "rohm,wdg-action",
> + "intb-only");
> + if (ret >= 0) {
> + ret = regmap_update_bits(w->regmap, BD96801_REG_WD_CONF,
> + BD96801_WD_ASSERT_MASK,
> + BD96801_WD_ASSERT_IRQ);
> + return ret;
> + }
> +
> + return 0;
> +}
> +
> +extern void emergency_restart(void);
> +static irqreturn_t bd96801_irq_hnd(int irq, void *data)
> +{
> + emergency_restart();
In case of a full system hang will this function get executed?
> + return IRQ_NONE;
> +}
> +
> +static int bd96801_wdt_probe(struct platform_device *pdev)
> +{
> + struct wdtbd96801 *w;
> + int ret, irq;
> + unsigned int val;
> +
> + w = devm_kzalloc(&pdev->dev, sizeof(*w), GFP_KERNEL);
> + if (!w)
> + return -ENOMEM;
> +
> + w->regmap = dev_get_regmap(pdev->dev.parent, NULL);
> + w->dev = &pdev->dev;
> +
> + w->wdt.info = &bd96801_wdt_info;
> + w->wdt.ops = &bd96801_wdt_ops;
> + w->wdt.parent = pdev->dev.parent;
> + w->wdt.timeout = DEFAULT_TIMEOUT;
> + watchdog_set_drvdata(&w->wdt, w);
> +
> + ret = regmap_read(w->regmap, BD96801_REG_WD_CONF, &val);
> + if (ret)
> + return dev_err_probe(&pdev->dev, ret,
> + "Failed to get the watchdog state\n");
> +
> + /*
> + * If the WDG is already enabled we assume it is configured by boot.
> + * In this case we just update the hw-timeout based on values set to
> + * the timeout / mode registers and leave the hardware configs
> + * untouched.
> + */
> + if ((val & BD96801_WD_EN_MASK) != BD96801_WD_DISABLE) {
> + dev_dbg(&pdev->dev, "watchdog was running during probe\n");
> + ret = bd96801_set_heartbeat_from_hw(w, val);
> + if (ret)
> + return ret;
> +
> + set_bit(WDOG_HW_RUNNING, &w->wdt.status);
> + } else {
> + /* If WDG is not running so we will initializate it */
> + ret = init_wdg_hw(w);
> + if (ret)
> + return ret;
> + }
> +
> + watchdog_init_timeout(&w->wdt, 0, pdev->dev.parent);
> + watchdog_set_nowayout(&w->wdt, nowayout);
> + watchdog_stop_on_reboot(&w->wdt);
> +
> + irq = platform_get_irq_byname(pdev, "bd96801-wdg");
> + if (irq > 0) {
> + ret = devm_request_threaded_irq(&pdev->dev, irq, NULL,
> + bd96801_irq_hnd,
> + IRQF_ONESHOT, "bd96801-wdg",
> + NULL);
> + if (ret)
> + return dev_err_probe(&pdev->dev, ret,
> + "Failed to register IRQ\n");
> + }
> +
> + return devm_watchdog_register_device(&pdev->dev, &w->wdt);
> +}
> +
> +static const struct platform_device_id bd96801_wdt_id[] = {
> + { "bd96801-wdt", },
> + { }
> +};
> +MODULE_DEVICE_TABLE(platform, bd96801_wdt_id);
> +
> +static struct platform_driver bd96801_wdt = {
> + .driver = {
> + .name = "bd96801-wdt"
> + },
> + .probe = bd96801_wdt_probe,
> + .id_table = bd96801_wdt_id,
> +};
> +module_platform_driver(bd96801_wdt);
> +
> +MODULE_AUTHOR("Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>");
> +MODULE_DESCRIPTION("BD96801 watchdog driver");
> +MODULE_LICENSE("GPL");
> --
> 2.43.2
>
>
> --
> Matti Vaittinen, Linux device drivers
> ROHM Semiconductors, Finland SWDC
> Kiviharjunlenkki 1E
> 90220 OULU
> FINLAND
>
> ~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
> Simon says - in Latin please.
> ~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
> Thanks to Simon Glass for the translation =]

-George

\
 
 \ /
  Last update: 2024-04-17 07:00    [W:0.108 / U:0.040 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site