lkml.org 
[lkml]   [2023]   [Jul]   [24]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v5] arm64: dts: ti: k3-j721s2: Add support for CAN instances 3 and 5 in main domain
Date
CAN instances 3 and 5 in the main domain are brought on the common
processor board through header J27 and J28. The CAN High and Low lines
from the SoC are routed through a mux on the SoM. The select lines need
to be set for the CAN signals to get connected to the transceivers on
the common processor board. Threfore, add respective mux, transceiver
dt nodes to add support for these CAN instances.

Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
---

Changelog v4->v5 : Modfied Mux Controller names

Link to v4 : https://lore.kernel.org/all/0070e00a-89c0-9b2b-8753-e1835b5aad15@ti.com/

.../dts/ti/k3-j721s2-common-proc-board.dts | 46 +++++++++++++++++++
arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi | 12 +++++
2 files changed, 58 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
index 04d4739d7245..e715fa12f9ca 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
@@ -29,6 +29,8 @@ aliases {
can0 = &main_mcan16;
can1 = &mcu_mcan0;
can2 = &mcu_mcan1;
+ can3 = &main_mcan3;
+ can4 = &main_mcan5;
};

evm_12v0: fixedregulator-evm12v0 {
@@ -109,6 +111,22 @@ transceiver2: can-phy2 {
standby-gpios = <&wkup_gpio0 2 GPIO_ACTIVE_HIGH>;
};

+ transceiver3: can-phy3 {
+ compatible = "ti,tcan1043";
+ #phy-cells = <0>;
+ max-bitrate = <5000000>;
+ standby-gpios = <&exp2 7 GPIO_ACTIVE_LOW>;
+ enable-gpios = <&exp2 6 GPIO_ACTIVE_HIGH>;
+ mux-states = <&mux0 1>;
+ };
+
+ transceiver4: can-phy4 {
+ compatible = "ti,tcan1042";
+ #phy-cells = <0>;
+ max-bitrate = <5000000>;
+ standby-gpios = <&exp_som 7 GPIO_ACTIVE_HIGH>;
+ mux-states = <&mux1 1>;
+ };
};

&main_pmx0 {
@@ -152,6 +170,20 @@ main_usbss0_pins_default: main-usbss0-default-pins {
J721S2_IOPAD(0x0ec, PIN_OUTPUT, 6) /* (AG25) TIMER_IO1.USB0_DRVVBUS */
>;
};
+
+ main_mcan3_pins_default: main-mcan3-pins-default {
+ pinctrl-single,pins = <
+ J721S2_IOPAD(0x080, PIN_INPUT, 0) /* (U26) MCASP0_AXR4.MCAN3_RX */
+ J721S2_IOPAD(0x07c, PIN_OUTPUT, 0) /* (T27) MCASP0_AXR3.MCAN3_TX */
+ >;
+ };
+
+ main_mcan5_pins_default: main-mcan5-pins-default {
+ pinctrl-single,pins = <
+ J721S2_IOPAD(0x03c, PIN_INPUT, 0) /* (U27) MCASP0_AFSX.MCAN5_RX */
+ J721S2_IOPAD(0x038, PIN_OUTPUT, 0) /* (AB28) MCASP0_ACLKX.MCAN5_TX */
+ >;
+ };
};

&wkup_pmx2 {
@@ -460,3 +492,17 @@ adc {
ti,adc-channels = <0 1 2 3 4 5 6 7>;
};
};
+
+&main_mcan3 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_mcan3_pins_default>;
+ phys = <&transceiver3>;
+};
+
+&main_mcan5 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_mcan5_pins_default>;
+ phys = <&transceiver4>;
+};
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
index d57dd43da0ef..594766482071 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
@@ -31,6 +31,18 @@ secure_ddr: optee@9e800000 {
};
};

+ mux0: mux-controller {
+ compatible = "gpio-mux";
+ #mux-state-cells = <1>;
+ mux-gpios = <&exp_som 1 GPIO_ACTIVE_HIGH>;
+ };
+
+ mux1: mux-controller {
+ compatible = "gpio-mux";
+ #mux-state-cells = <1>;
+ mux-gpios = <&exp_som 2 GPIO_ACTIVE_HIGH>;
+ };
+
transceiver0: can-phy0 {
/* standby pin has been grounded by default */
compatible = "ti,tcan1042";
--
2.34.1
\
 
 \ /
  Last update: 2023-07-24 13:19    [W:0.089 / U:0.024 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site