lkml.org 
[lkml]   [2020]   [Dec]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v3] pwm: bcm2835: Support apply function for atomic configuration
Date
Use the newer .apply function of pwm_ops instead of .config, .enable,
.disable and .set_polarity. This guarantees atomic changes of the pwm
controller configuration. It also reduces the size of the driver.

Since now period is a 64 bit value, add an extra check to reject periods
that exceed the possible max value for the 32 bit register.

This has been tested on a Raspberry PI 4.

Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
---

v3: Check against period truncation (based on a review by Uwe Kleine-König)
v2: Fix compiler error for 64 bit builds

drivers/pwm/pwm-bcm2835.c | 72 +++++++++++++++++------------------------------
1 file changed, 26 insertions(+), 46 deletions(-)

diff --git a/drivers/pwm/pwm-bcm2835.c b/drivers/pwm/pwm-bcm2835.c
index 6841dcf..d339898 100644
--- a/drivers/pwm/pwm-bcm2835.c
+++ b/drivers/pwm/pwm-bcm2835.c
@@ -58,13 +58,15 @@ static void bcm2835_pwm_free(struct pwm_chip *chip, struct pwm_device *pwm)
writel(value, pc->base + PWM_CONTROL);
}

-static int bcm2835_pwm_config(struct pwm_chip *chip, struct pwm_device *pwm,
- int duty_ns, int period_ns)
+static int bcm2835_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm,
+ const struct pwm_state *state)
{
+
struct bcm2835_pwm *pc = to_bcm2835_pwm(chip);
unsigned long rate = clk_get_rate(pc->clk);
+ unsigned long long period;
unsigned long scaler;
- u32 period;
+ u32 val;

if (!rate) {
dev_err(pc->dev, "failed to get clock rate\n");
@@ -72,65 +74,43 @@ static int bcm2835_pwm_config(struct pwm_chip *chip, struct pwm_device *pwm,
}

scaler = DIV_ROUND_CLOSEST(NSEC_PER_SEC, rate);
- period = DIV_ROUND_CLOSEST(period_ns, scaler);
+ /* set period */
+ period = DIV_ROUND_CLOSEST_ULL(state->period, scaler);

- if (period < PERIOD_MIN)
+ /* dont accept a period that is too small or has been truncated */
+ if ((period < PERIOD_MIN) || (period > U32_MAX))
return -EINVAL;

- writel(DIV_ROUND_CLOSEST(duty_ns, scaler),
- pc->base + DUTY(pwm->hwpwm));
- writel(period, pc->base + PERIOD(pwm->hwpwm));
-
- return 0;
-}
-
-static int bcm2835_pwm_enable(struct pwm_chip *chip, struct pwm_device *pwm)
-{
- struct bcm2835_pwm *pc = to_bcm2835_pwm(chip);
- u32 value;
-
- value = readl(pc->base + PWM_CONTROL);
- value |= PWM_ENABLE << PWM_CONTROL_SHIFT(pwm->hwpwm);
- writel(value, pc->base + PWM_CONTROL);
-
- return 0;
-}
-
-static void bcm2835_pwm_disable(struct pwm_chip *chip, struct pwm_device *pwm)
-{
- struct bcm2835_pwm *pc = to_bcm2835_pwm(chip);
- u32 value;
+ writel((u32) period, pc->base + PERIOD(pwm->hwpwm));

- value = readl(pc->base + PWM_CONTROL);
- value &= ~(PWM_ENABLE << PWM_CONTROL_SHIFT(pwm->hwpwm));
- writel(value, pc->base + PWM_CONTROL);
-}
+ /* set duty cycle */
+ val = DIV_ROUND_CLOSEST_ULL(state->duty_cycle, scaler);
+ writel(val, pc->base + DUTY(pwm->hwpwm));

-static int bcm2835_set_polarity(struct pwm_chip *chip, struct pwm_device *pwm,
- enum pwm_polarity polarity)
-{
- struct bcm2835_pwm *pc = to_bcm2835_pwm(chip);
- u32 value;
+ /* set polarity */
+ val = readl(pc->base + PWM_CONTROL);

- value = readl(pc->base + PWM_CONTROL);
+ if (state->polarity == PWM_POLARITY_NORMAL)
+ val &= ~(PWM_POLARITY << PWM_CONTROL_SHIFT(pwm->hwpwm));
+ else
+ val |= PWM_POLARITY << PWM_CONTROL_SHIFT(pwm->hwpwm);

- if (polarity == PWM_POLARITY_NORMAL)
- value &= ~(PWM_POLARITY << PWM_CONTROL_SHIFT(pwm->hwpwm));
+ /* enable/disable */
+ if (state->enabled)
+ val |= PWM_ENABLE << PWM_CONTROL_SHIFT(pwm->hwpwm);
else
- value |= PWM_POLARITY << PWM_CONTROL_SHIFT(pwm->hwpwm);
+ val &= ~(PWM_ENABLE << PWM_CONTROL_SHIFT(pwm->hwpwm));

- writel(value, pc->base + PWM_CONTROL);
+ writel(val, pc->base + PWM_CONTROL);

return 0;
}

+
static const struct pwm_ops bcm2835_pwm_ops = {
.request = bcm2835_pwm_request,
.free = bcm2835_pwm_free,
- .config = bcm2835_pwm_config,
- .enable = bcm2835_pwm_enable,
- .disable = bcm2835_pwm_disable,
- .set_polarity = bcm2835_set_polarity,
+ .apply = bcm2835_pwm_apply,
.owner = THIS_MODULE,
};

--
2.7.4
\
 
 \ /
  Last update: 2020-12-08 23:05    [W:0.083 / U:0.060 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site