lkml.org 
[lkml]   [2020]   [Oct]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 1/2] ARM: dts: sun8i: h2+: Fix Orange Pi Zero device description.
Date
There are two models of Orange Pi zero which are confusingly marketed
under the same name. Old model comes without a flash memory and current
model does have a flash memory. Build device tree for each model.

Signed-off-by: Michal Suchanek <msuchanek@suse.de>
---
arch/arm/boot/dts/Makefile | 1 +
.../sun8i-h2-plus-orangepi-zero-no-flash.dts | 210 ++++++++++++++++++
.../boot/dts/sun8i-h2-plus-orangepi-zero.dts | 201 +----------------
3 files changed, 215 insertions(+), 197 deletions(-)
create mode 100644 arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero-no-flash.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 4572db3fa5ae..f2853cea0c9c 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1168,6 +1168,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
sun8i-h2-plus-libretech-all-h3-cc.dtb \
sun8i-h2-plus-orangepi-r1.dtb \
sun8i-h2-plus-orangepi-zero.dtb \
+ sun8i-h2-plus-orangepi-zero-no-flash.dtb \
sun8i-h3-bananapi-m2-plus.dtb \
sun8i-h3-bananapi-m2-plus-v1.2.dtb \
sun8i-h3-beelink-x2.dtb \
diff --git a/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero-no-flash.dts b/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero-no-flash.dts
new file mode 100644
index 000000000000..3859b663e3f0
--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero-no-flash.dts
@@ -0,0 +1,210 @@
+/*
+ * Copyright (C) 2016 Icenowy Zheng <icenowy@aosc.xyz>
+ *
+ * Based on sun8i-h3-orangepi-one.dts, which is:
+ * Copyright (C) 2016 Hans de Goede <hdegoede@redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun8i-h3.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Xunlong Orange Pi Zero (old model without flash memory)";
+ compatible = "xunlong,orangepi-zero-no-flash",
+ "xunlong,orangepi-zero", "allwinner,sun8i-h2-plus";
+
+ aliases {
+ serial0 = &uart0;
+ /* ethernet0 is the H3 emac, defined in sun8i-h3.dtsi */
+ ethernet0 = &emac;
+ ethernet1 = &xr819;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ pwr_led {
+ label = "orangepi:green:pwr";
+ gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+
+ status_led {
+ label = "orangepi:red:status";
+ gpios = <&pio 0 17 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ reg_vcc_wifi: reg_vcc_wifi {
+ compatible = "regulator-fixed";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi";
+ enable-active-high;
+ gpio = <&pio 0 20 GPIO_ACTIVE_HIGH>;
+ };
+
+ reg_vdd_cpux: vdd-cpux-regulator {
+ compatible = "regulator-gpio";
+ regulator-name = "vdd-cpux";
+ regulator-type = "voltage";
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-ramp-delay = <50>; /* 4ms */
+
+ gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
+ enable-active-high;
+ gpios-states = <1>;
+ states = <1100000 0>, <1300000 1>;
+ };
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>;
+ post-power-on-delay-ms = <200>;
+ };
+};
+
+&cpu0 {
+ cpu-supply = <&reg_vdd_cpux>;
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&emac {
+ phy-handle = <&int_mii_phy>;
+ phy-mode = "mii";
+ allwinner,leds-active-low;
+ status = "okay";
+};
+
+&mmc0 {
+ vmmc-supply = <&reg_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+ status = "okay";
+};
+
+&mmc1 {
+ vmmc-supply = <&reg_vcc_wifi>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+
+ /*
+ * Explicitly define the sdio device, so that we can add an ethernet
+ * alias for it (which e.g. makes u-boot set a mac-address).
+ */
+ xr819: sdio_wifi@1 {
+ reg = <1>;
+ };
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&spi0 {
+ /* On the old model of Orange Pi Zero the flash memory is not mounted */
+ status = "disabled";
+
+ flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "mxicy,mx25l1606e", "winbond,w25q128";
+ reg = <0>;
+ spi-max-frequency = <40000000>;
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pa_pins>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+ status = "disabled";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+ status = "disabled";
+};
+
+&usb_otg {
+ dr_mode = "peripheral";
+ status = "okay";
+};
+
+&usbphy {
+ /*
+ * USB Type-A port VBUS is always on. However, MicroUSB VBUS can only
+ * power up the board; when it's used as OTG port, this VBUS is
+ * always off even if the board is powered via GPIO pins.
+ */
+ status = "okay";
+ usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
+};
diff --git a/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts b/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts
index f19ed981da9d..e718ed143ad7 100644
--- a/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts
+++ b/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts
@@ -1,209 +1,16 @@
-/*
- * Copyright (C) 2016 Icenowy Zheng <icenowy@aosc.xyz>
- *
- * Based on sun8i-h3-orangepi-one.dts, which is:
- * Copyright (C) 2016 Hans de Goede <hdegoede@redhat.com>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- * a) This file is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of the
- * License, or (at your option) any later version.
- *
- * This file is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- * b) Permission is hereby granted, free of charge, to any person
- * obtaining a copy of this software and associated documentation
- * files (the "Software"), to deal in the Software without
- * restriction, including without limitation the rights to use,
- * copy, modify, merge, publish, distribute, sublicense, and/or
- * sell copies of the Software, and to permit persons to whom the
- * Software is furnished to do so, subject to the following
- * conditions:
- *
- * The above copyright notice and this permission notice shall be
- * included in all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- * OTHER DEALINGS IN THE SOFTWARE.
- */
-
+// SPDX-License-Identifier: GPL-2.0
/dts-v1/;
-#include "sun8i-h3.dtsi"
-#include "sunxi-common-regulators.dtsi"
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
+#include "sun8i-h2-plus-orangepi-zero-no-flash.dts"

/ {
model = "Xunlong Orange Pi Zero";
- compatible = "xunlong,orangepi-zero", "allwinner,sun8i-h2-plus";
-
- aliases {
- serial0 = &uart0;
- /* ethernet0 is the H3 emac, defined in sun8i-h3.dtsi */
- ethernet0 = &emac;
- ethernet1 = &xr819;
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
-
- leds {
- compatible = "gpio-leds";
-
- pwr_led {
- label = "orangepi:green:pwr";
- gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
- default-state = "on";
- };
-
- status_led {
- label = "orangepi:red:status";
- gpios = <&pio 0 17 GPIO_ACTIVE_HIGH>;
- };
- };
-
- reg_vcc_wifi: reg_vcc_wifi {
- compatible = "regulator-fixed";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-name = "vcc-wifi";
- enable-active-high;
- gpio = <&pio 0 20 GPIO_ACTIVE_HIGH>;
- };
-
- reg_vdd_cpux: vdd-cpux-regulator {
- compatible = "regulator-gpio";
- regulator-name = "vdd-cpux";
- regulator-type = "voltage";
- regulator-boot-on;
- regulator-always-on;
- regulator-min-microvolt = <1100000>;
- regulator-max-microvolt = <1300000>;
- regulator-ramp-delay = <50>; /* 4ms */
-
- gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
- enable-active-high;
- gpios-states = <1>;
- states = <1100000 0>, <1300000 1>;
- };
-
- wifi_pwrseq: wifi_pwrseq {
- compatible = "mmc-pwrseq-simple";
- reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>;
- post-power-on-delay-ms = <200>;
- };
-};
-
-&cpu0 {
- cpu-supply = <&reg_vdd_cpux>;
-};
-
-&ehci0 {
- status = "okay";
-};
-
-&ehci1 {
- status = "okay";
-};
-
-&emac {
- phy-handle = <&int_mii_phy>;
- phy-mode = "mii";
- allwinner,leds-active-low;
- status = "okay";
-};
-
-&mmc0 {
- vmmc-supply = <&reg_vcc3v3>;
- bus-width = <4>;
- cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
- status = "okay";
-};
-
-&mmc1 {
- vmmc-supply = <&reg_vcc_wifi>;
- mmc-pwrseq = <&wifi_pwrseq>;
- bus-width = <4>;
- non-removable;
- status = "okay";
-
- /*
- * Explicitly define the sdio device, so that we can add an ethernet
- * alias for it (which e.g. makes u-boot set a mac-address).
- */
- xr819: sdio_wifi@1 {
- reg = <1>;
- };
+ compatible = "xunlong,orangepi-zero-with-flash",
+ "xunlong,orangepi-zero", "allwinner,sun8i-h2-plus";
};

-&ohci0 {
- status = "okay";
-};
-
-&ohci1 {
- status = "okay";
-};

&spi0 {
/* Disable SPI NOR by default: it optional on Orange Pi Zero boards */
- status = "disabled";
-
- flash@0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "mxicy,mx25l1606e", "winbond,w25q128";
- reg = <0>;
- spi-max-frequency = <40000000>;
- };
-};
-
-&uart0 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart0_pa_pins>;
status = "okay";
};

-&uart1 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart1_pins>;
- status = "disabled";
-};
-
-&uart2 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart2_pins>;
- status = "disabled";
-};
-
-&usb_otg {
- dr_mode = "peripheral";
- status = "okay";
-};
-
-&usbphy {
- /*
- * USB Type-A port VBUS is always on. However, MicroUSB VBUS can only
- * power up the board; when it's used as OTG port, this VBUS is
- * always off even if the board is powered via GPIO pins.
- */
- status = "okay";
- usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
-};
--
2.28.0
\
 
 \ /
  Last update: 2020-10-08 20:41    [W:0.108 / U:0.908 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site