lkml.org 
[lkml]   [2020]   [Jan]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
Subject[PATCH v3] iio: imu/mpu6050: support dual-edge IRQ
Make mpu6050 usable on platforms which provide only any-edge interrupts.
One example of this kind of platform is AT91SAM9G45

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>

---
v3: reword commit message
v2: just remove the dev_warn() message

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
---
drivers/iio/imu/inv_mpu6050/inv_mpu_core.c | 2 +-
drivers/iio/imu/inv_mpu6050/inv_mpu_ring.c | 5 +----
2 files changed, 2 insertions(+), 5 deletions(-)

diff --git a/drivers/iio/imu/inv_mpu6050/inv_mpu_core.c b/drivers/iio/imu/inv_mpu6050/inv_mpu_core.c
index 2261c6c4ac65..4cfdd19ee4fc 100644
--- a/drivers/iio/imu/inv_mpu6050/inv_mpu_core.c
+++ b/drivers/iio/imu/inv_mpu6050/inv_mpu_core.c
@@ -1118,7 +1118,7 @@ int inv_mpu_core_probe(struct regmap *regmap, int irq, const char *name,
irq_type = irqd_get_trigger_type(desc);
if (!irq_type)
irq_type = IRQF_TRIGGER_RISING;
- if (irq_type == IRQF_TRIGGER_RISING)
+ if (irq_type & IRQF_TRIGGER_RISING) // rising or both-edge
st->irq_mask = INV_MPU6050_ACTIVE_HIGH;
else if (irq_type == IRQF_TRIGGER_FALLING)
st->irq_mask = INV_MPU6050_ACTIVE_LOW;
diff --git a/drivers/iio/imu/inv_mpu6050/inv_mpu_ring.c b/drivers/iio/imu/inv_mpu6050/inv_mpu_ring.c
index 72d8c5790076..a8a833f8b99b 100644
--- a/drivers/iio/imu/inv_mpu6050/inv_mpu_ring.c
+++ b/drivers/iio/imu/inv_mpu6050/inv_mpu_ring.c
@@ -180,11 +180,8 @@ irqreturn_t inv_mpu6050_read_fifo(int irq, void *p)
"failed to ack interrupt\n");
goto flush_fifo;
}
- if (!(int_status & INV_MPU6050_BIT_RAW_DATA_RDY_INT)) {
- dev_warn(regmap_get_device(st->map),
- "spurious interrupt with status 0x%x\n", int_status);
+ if (!(int_status & INV_MPU6050_BIT_RAW_DATA_RDY_INT))
goto end_session;
- }

if (!(st->chip_config.accl_fifo_enable |
st->chip_config.gyro_fifo_enable))
--
2.20.1
\
 
 \ /
  Last update: 2020-01-11 16:20    [W:0.038 / U:0.740 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site