lkml.org 
[lkml]   [2019]   [Feb]   [15]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v2] x86/tsc: Allow quick PIT calibration despite interruptions

* Jan H. Schönherr <jan@schnhrr.de> wrote:

> Some systems experience regular interruptions (60 Hz SMI?), that prevent
> the quick PIT calibration from succeeding: individual interruptions can be
> so long, that the PIT MSB is observed to decrement by 2 or 3 instead of 1.
> The existing code cannot recover from this.
>
> The system in question is an AMD Ryzen Threadripper 2950X, microcode
> 0x800820b, on an ASRock Fatal1ty X399 Professional Gaming, BIOS P3.30.
>
> Change the code to handle (almost) arbitrary interruptions, as long
> as they happen only once in a while and they do not take too long.
> Specifically, also cover an interruption during the very first reads.
>
> Signed-off-by: Jan H. Schönherr <jan@schnhrr.de>
> ---
>
> v2:
> - Dropped the other hacky patch for the time being.
> - Fixed the early exit check.
> - Hopefully fixed all inaccurate math in v1.
> - Extended comments.
>
> arch/x86/kernel/tsc.c | 91 +++++++++++++++++++++++++++----------------
> 1 file changed, 57 insertions(+), 34 deletions(-)
>
> diff --git a/arch/x86/kernel/tsc.c b/arch/x86/kernel/tsc.c
> index e9f777bfed40..aced427371f7 100644
> --- a/arch/x86/kernel/tsc.c
> +++ b/arch/x86/kernel/tsc.c
> @@ -485,7 +485,7 @@ static inline int pit_verify_msb(unsigned char val)
> static inline int pit_expect_msb(unsigned char val, u64 *tscp, unsigned long *deltap)
> {
> int count;
> - u64 tsc = 0, prev_tsc = 0;
> + u64 tsc = get_cycles(), prev_tsc = 0;
>
> for (count = 0; count < 50000; count++) {
> if (!pit_verify_msb(val))
> @@ -500,7 +500,7 @@ static inline int pit_expect_msb(unsigned char val, u64 *tscp, unsigned long *de
> * We require _some_ success, but the quality control
> * will be based on the error terms on the TSC values.
> */
> - return count > 5;
> + return count > 0 && pit_verify_msb(val - 1);
> }
>
> /*
> @@ -515,7 +515,8 @@ static inline int pit_expect_msb(unsigned char val, u64 *tscp, unsigned long *de
> static unsigned long quick_pit_calibrate(void)
> {
> int i;
> - u64 tsc, delta;
> + u64 tsc = 0, delta;
> + unsigned char start;
> unsigned long d1, d2;
>
> if (!has_legacy_pic())
> @@ -547,43 +548,65 @@ static unsigned long quick_pit_calibrate(void)
> */
> pit_verify_msb(0);
>
> - if (pit_expect_msb(0xff, &tsc, &d1)) {
> - for (i = 1; i <= MAX_QUICK_PIT_ITERATIONS; i++) {
> - if (!pit_expect_msb(0xff-i, &delta, &d2))
> - break;
> -
> - delta -= tsc;
> -
> - /*
> - * Extrapolate the error and fail fast if the error will
> - * never be below 500 ppm.
> - */
> - if (i == 1 &&
> - d1 + d2 >= (delta * MAX_QUICK_PIT_ITERATIONS) >> 11)
> - return 0;
> -
> - /*
> - * Iterate until the error is less than 500 ppm
> - */
> - if (d1+d2 >= delta >> 11)
> - continue;
> -
> - /*
> - * Check the PIT one more time to verify that
> - * all TSC reads were stable wrt the PIT.
> - *
> - * This also guarantees serialization of the
> - * last cycle read ('d2') in pit_expect_msb.
> - */
> - if (!pit_verify_msb(0xfe - i))
> - break;
> - goto success;
> + /*
> + * Reading the PIT may fail or experience unexpected delays (due to
> + * SMIs, for example). Assuming, that these underlying interruptions
> + * happen only once in a while, we wait for two successful reads.
> + * Of these, we assume that the better one was not delayed and use
> + * it as the base for later calculations.
> + */
> + for (i = 0; i <= MAX_QUICK_PIT_ITERATIONS; i++) {
> + if (!pit_expect_msb(0xff - i, &delta, &d2))
> + continue;
> +
> + if (!tsc) {
> + /* first success */
> + start = i;
> + tsc = delta;
> + d1 = d2;
> + continue;
> }


The logic looks mostly good to me, but do we really want to use 'delta'
as an implicit success-counter here? In principle 'delta' could end up
being 0 due to some TSC borkage, and we'd interpret that as "first
success", which it clearly isn't.

The end result will still be a 'failure', but why not use a proper
separate variable to count attempts and make the code easier to read and
failure scenarios more predictable?

Thanks,

Ingo

\
 
 \ /
  Last update: 2019-02-15 10:37    [W:0.138 / U:0.184 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site