Messages in this thread | | | Subject | Re: [PATCH V4 3/8] backlight: qcom-wled: Add new properties for PMI8998 | From | Daniel Thompson <> | Date | Fri, 20 Jul 2018 14:15:24 +0100 |
| |
On 09/07/18 11:22, Kiran Gunda wrote: > Update the bindings with the new properties used for > PMI8998. > > Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
> --- > Changes from V3: > - Removed the default values. > - Removed pmi8998 example. > > .../bindings/leds/backlight/qcom-wled.txt | 76 ++++++++++++++++++---- > 1 file changed, 62 insertions(+), 14 deletions(-) > > diff --git a/Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt b/Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt > index 14f28f2..3f22ced 100644 > --- a/Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt > +++ b/Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt > @@ -20,8 +20,7 @@ platforms. The PMIC is connected to the host processor via SPMI bus. > - default-brightness > Usage: optional > Value type: <u32> > - Definition: brightness value on boot, value from: 0-4095 > - Default: 2048 > + Definition: brightness value on boot, value from: 0-4095. > > - label > Usage: required > @@ -48,20 +47,24 @@ platforms. The PMIC is connected to the host processor via SPMI bus. > - qcom,current-limit > Usage: optional > Value type: <u32> > - Definition: mA; per-string current limit > - value: For pm8941: from 0 to 25 with 5 mA step > - Default 20 mA. > - For pmi8998: from 0 to 30 with 5 mA step > - Default 25 mA. > + Definition: mA; per-string current limit; value from 0 to 25 with > + 1 mA step. > + This property is supported only for pm8941. > + > +- qcom,current-limit-microamp > + Usage: optional > + Value type: <u32> > + Definition: uA; per-string current limit; value from 0 to 30000 with > + 2500 uA step. > > - qcom,current-boost-limit > Usage: optional > Value type: <u32> > Definition: mA; boost current limit. > For pm8941: one of: 105, 385, 525, 805, 980, 1260, 1400, > - 1680. Default: 805 mA > + 1680. > For pmi8998: one of: 105, 280, 450, 620, 970, 1150, 1300, > - 1500. Default: 970 mA > + 1500. > > - qcom,switching-freq > Usage: optional > @@ -69,22 +72,66 @@ platforms. The PMIC is connected to the host processor via SPMI bus. > Definition: kHz; switching frequency; one of: 600, 640, 685, 738, > 800, 872, 960, 1066, 1200, 1371, 1600, 1920, 2400, 3200, > 4800, 9600. > - Default: for pm8941: 1600 kHz > - for pmi8998: 800 kHz > > - qcom,ovp > Usage: optional > Value type: <u32> > Definition: V; Over-voltage protection limit; one of: > - 27, 29, 32, 35. default: 29V > + 27, 29, 32, 35. > This property is supported only for PM8941. > > +- qcom,ovp-millivolt > + Usage: optional > + Value type: <u32> > + Definition: mV; Over-voltage protection limit; > + For pmi8998: one of 18100, 19600, 29600, 31100 > + If this property is not specified for PM8941, it > + falls back to "qcom,ovp" property. > + > - qcom,num-strings > Usage: optional > Value type: <u32> > Definition: #; number of led strings attached; > - value from 1 to 3. default: 2 > - This property is supported only for PM8941. > + value: For PM8941 from 1 to 3. > + For PMI8998 from 1 to 4. > + > +- interrupts > + Usage: optional > + Value type: <prop encoded array> > + Definition: Interrupts associated with WLED. This should be > + "short" and "ovp" interrupts. Interrupts can be > + specified as per the encoding listed under > + Documentation/devicetree/bindings/spmi/ > + qcom,spmi-pmic-arb.txt. > + > +- interrupt-names > + Usage: optional > + Value type: <string> > + Definition: Interrupt names associated with the interrupts. > + Must be "short" and "ovp". The short circuit detection > + is not supported for PM8941. > + > +- qcom,enabled-strings > + Usage: optional > + Value tyoe: <u32 array> > + Definition: Array of the WLED strings numbered from 0 to 3. Each > + string of leds are operated individually. Specify the > + list of strings used by the device. Any combination of > + led strings can be used. > + > +- qcom,external-pfet > + Usage: optional > + Value type: <bool> > + Definition: Specify if external PFET control for short circuit > + protection is used. This property is supported only > + for PMI8998. > + > +- qcom,auto-string-detection > + Usage: optional > + Value type: <bool> > + Definition: Enables auto-detection of the WLED string configuration. > + This feature is not supported for PM8941. > + > > Example: > > @@ -99,4 +146,5 @@ pm8941-wled@d800 { > qcom,switching-freq = <1600>; > qcom,ovp = <29>; > qcom,num-strings = <2>; > + qcom,enabled-strings = <0x00 0x01>; > }; >
| |