lkml.org 
[lkml]   [2018]   [Oct]   [24]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v2 14/15] arm64: dts: allwinner: a64: Add DSI pipeline
On Tue, Oct 23, 2018 at 09:20:34PM +0530, Jagan Teki wrote:
> The A64 has a MIPI-DSI block which is similar to A31
> without mod clock.
>
> So, add dsi node with A64 compatible, dphy node with
> A31 compatible and finally connect dsi to tcon0 to
> make proper DSI pipeline.
>
> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
> ---
> Changes for v2:
> - use A64 dphy compatible
>
> arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi | 45 +++++++++++++++++++
> 1 file changed, 45 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
> index f3a66f888205..f82e6b165d57 100644
> --- a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
> @@ -320,6 +320,11 @@
> #address-cells = <1>;
> #size-cells = <0>;
> reg = <1>;
> +
> + tcon0_out_dsi: endpoint@1 {
> + reg = <1>;
> + remote-endpoint = <&dsi_in_tcon0>;

You need to set the allwinner,channel property there.

> + };
> };
> };
> };
> @@ -818,6 +823,46 @@
> #interrupt-cells = <3>;
> };
>
> +
> + dsi: dsi@1ca0000 {
> + compatible = "allwinner,sun50i-a64-mipi-dsi";
> + reg = <0x01ca0000 0x1000>;
> + interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ccu CLK_BUS_MIPI_DSI>;
> + clock-names = "bus";
> + resets = <&ccu RST_BUS_MIPI_DSI>;
> + phys = <&dphy>;
> + phy-names = "dphy";
> + status = "disabled";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0>;
> +
> + dsi_in_tcon0: endpoint {
> + remote-endpoint = <&tcon0_out_dsi>;
> + };
> + };
> + };
> + };
> +
> + dphy: d-phy@1ca1000 {
> + compatible = "allwinner,sun50i-a64-mipi-dphy",
> + "allwinner,sun6i-a31-mipi-dphy";
> + reg = <0x01ca1000 0x1000>;
> + clocks = <&ccu CLK_BUS_MIPI_DSI>,
> + <&ccu CLK_DSI_DPHY>;
> + clock-names = "bus", "mod";
> + resets = <&ccu RST_BUS_MIPI_DSI>;
> + status = "disabled";
> + #phy-cells = <0>;
> + };
> +

You have to order the nodes per ascending physical address ordering.

Maxime

--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com
[unhandled content-type:application/pgp-signature]
\
 
 \ /
  Last update: 2018-10-24 20:12    [W:0.205 / U:0.104 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site