lkml.org 
[lkml]   [2017]   [May]   [12]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH] usb-musb: keep VBUS on when device is disconnected
* Bin Liu <b-liu@ti.com> [170512 06:43]:
> On Thu, May 11, 2017 at 02:06:28PM -0700, Tony Lindgren wrote:
> >
> > Well maybe the minimal fix for now is just pretty much back to
> > square one of this thread. This should keep VBUS always on.
> > Then we can figure out some logic to cut VBUS later on.
> >
> > And yeah, the state machine is really hard to follow so some kind
> > of clean up would be nice.
>
> Okay, figured out why clearing session in OTG_STATE_A_WAIT_BCON, it is
> not for error condition handling (which is done in musb-core), but for
> going back to b_idle state from a_host for dual-role mode. otg_timer()
> (now is dsps_check_status()) was only called for otg port originally, so
> it wasn't an issue, until started calling it for host mode as well when
> runtime PM was added.

OK makes sense.

> > 8< -------------------
> > --- a/drivers/usb/musb/musb_dsps.c
> > +++ b/drivers/usb/musb/musb_dsps.c
> > @@ -245,7 +245,6 @@ static int dsps_check_status(struct musb *musb, void *unused)
> > dsps_mod_timer_optional(glue);
> > break;
> > case OTG_STATE_A_WAIT_BCON:
> > - musb_writeb(musb->mregs, MUSB_DEVCTL, 0);
> > skip_session = 1;
> > /* fall */
> >
>
> So the above patch breaks otg port when switching from host to device
> mode. The following change should solve it. But Tony do you see any way
> to improve it with glue->vbus_irq?

OK. No better ideas except I think we should probably have a separate
timer for keeping VBUS on after state changes eventually.

I guess the real test here would be to connect a USB modem that
changes state to the am335x-evm OTG port and make sure it works
with commit similar to d680414d0f42 ("ARM: dts: Configure BeagleBone
peripheral USB VBUS irq"). And also without configuring the vusb_irq.

For the patch below, seems like the way to go for the fix assuming
it fixes the $subject issue:

Acked-by: Tony Lindgren <tony@atomide.com>

> 8< --------------------
> diff --git a/drivers/usb/musb/musb_dsps.c b/drivers/usb/musb/musb_dsps.c
> index 9c7ee26ef388..465281244596 100644
> --- a/drivers/usb/musb/musb_dsps.c
> +++ b/drivers/usb/musb/musb_dsps.c
> @@ -245,9 +245,14 @@ static int dsps_check_status(struct musb *musb, void *unused)
> dsps_mod_timer_optional(glue);
> break;
> case OTG_STATE_A_WAIT_BCON:
> + /* keep VBUS on for host-only mode */
> + if (musb->port_mode == MUSB_PORT_MODE_HOST) {
> + dsps_mod_timer_optional(glue);
> + break;
> + }
> musb_writeb(musb->mregs, MUSB_DEVCTL, 0);
> skip_session = 1;
> - /* fall */
> + /* fall through */
>
> case OTG_STATE_A_IDLE:
> case OTG_STATE_B_IDLE:

\
 
 \ /
  Last update: 2017-05-12 16:59    [W:0.125 / U:0.032 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site