lkml.org 
[lkml]   [2017]   [May]   [12]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH] usb-musb: keep VBUS on when device is disconnected
From
Date


> Il giorno 12 mag 2017, alle ore 17:21, Bin Liu <b-liu@ti.com> ha scritto:
>
> On Fri, May 12, 2017 at 07:58:49AM -0700, Tony Lindgren wrote:
>> * Bin Liu <b-liu@ti.com> [170512 06:43]:
>>> On Thu, May 11, 2017 at 02:06:28PM -0700, Tony Lindgren wrote:
>>>>
>>>> Well maybe the minimal fix for now is just pretty much back to
>>>> square one of this thread. This should keep VBUS always on.
>>>> Then we can figure out some logic to cut VBUS later on.
>>>>
>>>> And yeah, the state machine is really hard to follow so some kind
>>>> of clean up would be nice.
>>>
>>> Okay, figured out why clearing session in OTG_STATE_A_WAIT_BCON, it is
>>> not for error condition handling (which is done in musb-core), but for
>>> going back to b_idle state from a_host for dual-role mode. otg_timer()
>>> (now is dsps_check_status()) was only called for otg port originally, so
>>> it wasn't an issue, until started calling it for host mode as well when
>>> runtime PM was added.
>>
>> OK makes sense.
>>
>>>> 8< -------------------
>>>> --- a/drivers/usb/musb/musb_dsps.c
>>>> +++ b/drivers/usb/musb/musb_dsps.c
>>>> @@ -245,7 +245,6 @@ static int dsps_check_status(struct musb *musb, void *unused)
>>>> dsps_mod_timer_optional(glue);
>>>> break;
>>>> case OTG_STATE_A_WAIT_BCON:
>>>> - musb_writeb(musb->mregs, MUSB_DEVCTL, 0);
>>>> skip_session = 1;
>>>> /* fall */
>>>>
>>>
>>> So the above patch breaks otg port when switching from host to device
>>> mode. The following change should solve it. But Tony do you see any way
>>> to improve it with glue->vbus_irq?
>>
>> OK. No better ideas except I think we should probably have a separate
>> timer for keeping VBUS on after state changes eventually.
>
> Currently with the patch below, VBUS is constantly on for host-only
> mode, and this is what we want. Why we need a separate timer? No one
> cuts VBUs now for host-only mode.
>
>>
>> I guess the real test here would be to connect a USB modem that
>> changes state to the am335x-evm OTG port and make sure it works
>> with commit similar to d680414d0f42 ("ARM: dts: Configure BeagleBone
>> peripheral USB VBUS irq"). And also without configuring the vusb_irq.
>
> I will test w/ and w/o vbus_irq on BeagleBone.
>
> Moreno, would you mind to test the patch below with your modem?
>
> Thanks,
> -Bin.
>
>>
>> For the patch below, seems like the way to go for the fix assuming
>> it fixes the $subject issue:
>>
>> Acked-by: Tony Lindgren <tony@atomide.com>
>>
>>> 8< --------------------
>>> diff --git a/drivers/usb/musb/musb_dsps.c b/drivers/usb/musb/musb_dsps.c
>>> index 9c7ee26ef388..465281244596 100644
>>> --- a/drivers/usb/musb/musb_dsps.c
>>> +++ b/drivers/usb/musb/musb_dsps.c
>>> @@ -245,9 +245,14 @@ static int dsps_check_status(struct musb *musb, void *unused)
>>> dsps_mod_timer_optional(glue);
>>> break;
>>> case OTG_STATE_A_WAIT_BCON:
>>> + /* keep VBUS on for host-only mode */
>>> + if (musb->port_mode == MUSB_PORT_MODE_HOST) {
>>> + dsps_mod_timer_optional(glue);
>>> + break;
>>> + }
>>> musb_writeb(musb->mregs, MUSB_DEVCTL, 0);
>>> skip_session = 1;
>>> - /* fall */
>>> + /* fall through */
>>>
>>> case OTG_STATE_A_IDLE:
>>> case OTG_STATE_B_IDLE:

Hello Bin,

today is too late, here.

I’ll try to test it on Monday.

Best regards,

Moreno

\
 
 \ /
  Last update: 2017-05-12 18:01    [W:0.170 / U:0.704 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site