lkml.org 
[lkml]   [2016]   [Dec]   [12]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v5 1/2] Add OV5647 device tree documentation
From
Date
Hi Sakari

On 12/12/2016 11:49 AM, Sakari Ailus wrote:
> Hi Ramiro,
>
> On Mon, Dec 12, 2016 at 11:39:31AM +0000, Ramiro Oliveira wrote:
>> Hi Sakari,
>>
>> Thank you for the feedback.
>>
>> On 12/7/2016 10:33 PM, Sakari Ailus wrote:
>>> Hi Ramiro,
>>>
>>> Thank you for the patch.
>>>
>>> On Mon, Dec 05, 2016 at 05:36:33PM +0000, Ramiro Oliveira wrote:
>>>> Add device tree documentation.
>>>>
>>>> Signed-off-by: Ramiro Oliveira <roliveir@synopsys.com>
>>>> ---
>>>> .../devicetree/bindings/media/i2c/ov5647.txt | 19 +++++++++++++++++++
>>>> 1 file changed, 19 insertions(+)
>>>> create mode 100644 Documentation/devicetree/bindings/media/i2c/ov5647.txt
>>>>
>>>> diff --git a/Documentation/devicetree/bindings/media/i2c/ov5647.txt b/Documentation/devicetree/bindings/media/i2c/ov5647.txt
>>>> new file mode 100644
>>>> index 0000000..4c91b3b
>>>> --- /dev/null
>>>> +++ b/Documentation/devicetree/bindings/media/i2c/ov5647.txt
>>>> @@ -0,0 +1,19 @@
>>>> +Omnivision OV5647 raw image sensor
>>>> +---------------------------------
>>>> +
>>>> +OV5647 is a raw image sensor with MIPI CSI-2 and CCP2 image data interfaces
>>>> +and CCI (I2C compatible) control bus.
>>>> +
>>>> +Required properties:
>>>> +
>>>> +- compatible : "ovti,ov5647";
>>>> +- reg : I2C slave address of the sensor;
>>>> +
>>>> +The common video interfaces bindings (see video-interfaces.txt) should be
>>>> +used to specify link to the image data receiver. The OV5647 device
>>>> +node should contain one 'port' child node with an 'endpoint' subnode.
>>>> +
>>>> +Following properties are valid for the endpoint node:
>>>> +
>>>> +- data-lanes : (optional) specifies MIPI CSI-2 data lanes as covered in
>>>> + video-interfaces.txt. The sensor supports only two data lanes.
>>>
>>> Doesn't this sensor require a external clock, a reset GPIO and / or a
>>> regulator or a few? Do you need data-lanes, unless you can change the order
>>> or the number?
>>
>> In the setup I'm using, I'm not aware of any reset GPIO or regulator. I do use a
>> external clock but it's fixed and not controlled by SW. Should I add a property
>> for this?
>
> The sensor datasheet defines a power-up and power-down sequence for the
> device. If you don't implement these sequences in the driver on a DT based
> system, nothing suggests that they're implemented correctly. Could it be
> that the boot loader simply enables the regulators or another device
> requires them to be enabled?
>
> I presume at least the reset GPIO should be controlled explicitly in order
> to ensure correct function. Although hardware can be surprising: I have one
> production system that has no reset GPIO for the sensor albeit the sensor
> datasheet says that's part of the power up sequence.
>

Sorry for the misunderstanding. I wanted to say that, there is no SW controlled
reset. In the board we're using to connect the sensor to our D-PHY we have a
GPIO controller that when it receives power, it removes the sensor from reset,
so I have no control over that.

Regarding the clock, should I create a new property?

And also, regarding the data-lanes, AFAIK it isn't possible to change the order
of the data and clock lanes so should I remove that property?

>>
>>>
>>> An example DT snippet wouldn't hurt.
>>
>> Sure, I can add a example snippet.
>>
>>>
>>
>

\
 
 \ /
  Last update: 2016-12-12 13:16    [W:1.402 / U:0.492 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site