lkml.org 
[lkml]   [2016]   [Dec]   [12]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
SubjectRe: [PATCH v5 1/2] Add OV5647 device tree documentation
Hi Ramiro,

On Mon, Dec 12, 2016 at 11:39:31AM +0000, Ramiro Oliveira wrote:
> Hi Sakari,
>
> Thank you for the feedback.
>
> On 12/7/2016 10:33 PM, Sakari Ailus wrote:
> > Hi Ramiro,
> >
> > Thank you for the patch.
> >
> > On Mon, Dec 05, 2016 at 05:36:33PM +0000, Ramiro Oliveira wrote:
> >> Add device tree documentation.
> >>
> >> Signed-off-by: Ramiro Oliveira <roliveir@synopsys.com>
> >> ---
> >> .../devicetree/bindings/media/i2c/ov5647.txt | 19 +++++++++++++++++++
> >> 1 file changed, 19 insertions(+)
> >> create mode 100644 Documentation/devicetree/bindings/media/i2c/ov5647.txt
> >>
> >> diff --git a/Documentation/devicetree/bindings/media/i2c/ov5647.txt b/Documentation/devicetree/bindings/media/i2c/ov5647.txt
> >> new file mode 100644
> >> index 0000000..4c91b3b
> >> --- /dev/null
> >> +++ b/Documentation/devicetree/bindings/media/i2c/ov5647.txt
> >> @@ -0,0 +1,19 @@
> >> +Omnivision OV5647 raw image sensor
> >> +---------------------------------
> >> +
> >> +OV5647 is a raw image sensor with MIPI CSI-2 and CCP2 image data interfaces
> >> +and CCI (I2C compatible) control bus.
> >> +
> >> +Required properties:
> >> +
> >> +- compatible : "ovti,ov5647";
> >> +- reg : I2C slave address of the sensor;
> >> +
> >> +The common video interfaces bindings (see video-interfaces.txt) should be
> >> +used to specify link to the image data receiver. The OV5647 device
> >> +node should contain one 'port' child node with an 'endpoint' subnode.
> >> +
> >> +Following properties are valid for the endpoint node:
> >> +
> >> +- data-lanes : (optional) specifies MIPI CSI-2 data lanes as covered in
> >> + video-interfaces.txt. The sensor supports only two data lanes.
> > Doesn't this sensor require a external clock, a reset GPIO and / or a
> > regulator or a few? Do you need data-lanes, unless you can change the order
> > or the number?
>
> In the setup I'm using, I'm not aware of any reset GPIO or regulator. I do use a
> external clock but it's fixed and not controlled by SW. Should I add a property
> for this?

The sensor datasheet defines a power-up and power-down sequence for the
device. If you don't implement these sequences in the driver on a DT based
system, nothing suggests that they're implemented correctly. Could it be
that the boot loader simply enables the regulators or another device
requires them to be enabled?

I presume at least the reset GPIO should be controlled explicitly in order
to ensure correct function. Although hardware can be surprising: I have one
production system that has no reset GPIO for the sensor albeit the sensor
datasheet says that's part of the power up sequence.

>
> >
> > An example DT snippet wouldn't hurt.
>
> Sure, I can add a example snippet.
>
> >
>

--
Kind regards,

Sakari Ailus
e-mail: sakari.ailus@iki.fi XMPP: sailus@retiisi.org.uk

\
 
 \ /
  Last update: 2016-12-12 12:50    [W:0.942 / U:0.544 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site