lkml.org 
[lkml]   [2016]   [Nov]   [22]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2 1/4] dt-bindings: phy: Add support for QUSB2 phy
Date
Qualcomm chipsets have QUSB2 phy controller that provides
HighSpeed functionality for DWC3 controller.
Adding dt binding information for the same.

Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
---

Changes since v1:
- New patch, forked out of the original driver patch:
"phy: qcom-qusb2: New driver for QUSB2 PHY on Qcom chips"
- Updated dt bindings to remove 'hstx-trim-bit-offset' and
'hstx-trim-bit-len' bindings.

.../devicetree/bindings/phy/qcom-qusb2-phy.txt | 55 ++++++++++++++++++++++
1 file changed, 55 insertions(+)
create mode 100644 Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt

diff --git a/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt b/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt
new file mode 100644
index 0000000..38c8b30
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt
@@ -0,0 +1,55 @@
+Qualcomm QUSB2 phy controller
+=============================
+
+QUSB2 controller supports LS/FS/HS usb connectivity on Qualcomm chipsets.
+
+Required properties:
+ - compatible: compatible list, contains "qcom,msm8996-qusb2-phy".
+ - reg: offset and length of the PHY register set.
+ - #phy-cells: must be 0.
+
+ - clocks: a list of phandles and clock-specifier pairs,
+ one for each entry in clock-names.
+ - clock-names: must be "cfg_ahb" for phy config clock,
+ "ref_clk" for 19.2 MHz ref clk,
+ "ref_clk_src" reference clock source.
+ "iface" for phy interface clock (Optional).
+
+ - vdd-phy-supply: Phandle to a regulator supply to PHY core block.
+ - vdda-pll-supply: Phandle to 1.8V regulator supply to PHY refclk pll block.
+ - vdda-phy-dpdm: Phandle to 3.1V regulator supply to Dp/Dm port signals.
+
+ - resets: a list of phandles and reset controller specifier pairs,
+ one for each entry in reset-names.
+ - reset-names: must be "phy" for reset of phy block.
+
+Optional properties:
+ - nvmem-cells: a list of phandles to nvmem cells that contain fused
+ tuning parameters for qusb2 phy, one for each entry
+ in nvmem-cell-names.
+ - nvmem-cell-names: must be "tune2_hstx_trim_efuse" for cell containing
+ HS Tx trim value.
+
+ - qcom,tcsr-syscon: Phandle to TCSR syscon register region.
+
+Example:
+ hsphy: qusb2phy@7411000 {
+ compatible = "qcom,msm8996-qusb2-phy";
+ reg = <0x07411000 0x180>;
+ #phy-cells = <0>;
+
+ clocks = <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
+ <&gcc GCC_RX1_USB2_CLKREF_CLK>,
+ <&rpmcc MSM8996_RPM_SMD_LN_BB_CLK>;
+ clock-names = "cfg_ahb_clk", "ref_clk", "ref_clk_src";
+
+ vdd-phy-supply = <&pm8994_s2>;
+ vdda-pll-supply = <&pm8994_l12>;
+ vdda-phy-dpdm-supply = <&pm8994_l24>;
+
+ resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
+ reset-names = "phy";
+
+ nvmem-cells = <&qusb2p_hstx_trim>;
+ nvmem-cell-names = "tune2_hstx_trim_efuse";
+ };
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
\
 
 \ /
  Last update: 2016-11-22 13:04    [W:0.186 / U:1.660 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site