lkml.org 
[lkml]   [2016]   [Nov]   [28]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v2 3/4] dt-bindings: phy: Add support for QMP phy
On 11/22, Vivek Gautam wrote:
> diff --git a/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt b/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt
> new file mode 100644
> index 0000000..ffb173b
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt
> @@ -0,0 +1,74 @@
> +Qualcomm QMP PHY
> +----------------
> +
> +QMP phy controller supports physical layer functionality for a number of
> +controllers on Qualcomm chipsets, such as, PCIe, UFS, and USB.
> +
> +Required properties:
> + - compatible: compatible list, contains:
> + "qcom,msm8996-qmp-pcie-phy" for 14nm PCIe phy on msm8996,
> + "qcom,msm8996-qmp-usb3-phy" for 14nm USB3 phy on msm8996.
> + - reg: list of offset and length pair of the PHY register sets.
> + at index 0: offset and length of register set for PHY common
> + serdes block.
> + from index 1 - N: offset and length of register set for each lane,
> + for N number of phy lanes (ports).
> + - lane-offsets: array of offsets to tx, rx and pcs blocks for phy lanes.
> + - #phy-cells: must be 1
> + - Cell after phy phandle should be the port (lane) number.
> + - clocks: a list of phandles and clock-specifier pairs,
> + one for each entry in clock-names.
> + - clock-names: must be "cfg_ahb" for phy config clock,
> + "aux" for phy aux clock,
> + "ref_clk" for 19.2 MHz ref clk,
> + "ref_clk_src" for reference clock source,

We typically leave "clk" out of clk names because it's redundant.

> + "pipe<port-number>" for pipe clock specific to
> + each port/lane (Optional).

The pipe clocks are orphaned right now. We should add an output
clock from the phy to go into the controller and back into the
phy if I recall correctly. The phy should be a clock provider
itself so it can output the pipe clock source into GCC and back
into the phy and controller.

> + - resets: a list of phandles and reset controller specifier pairs,
> + one for each entry in reset-names.
> + - reset-names: must be "phy" for reset of phy block,
> + "common" for phy common block reset,
> + "cfg" for phy's ahb cfg block reset (Optional).
> + "port<port-number>" for reset specific to
> + each port/lane (Optional).
> + - vdda-phy-supply: Phandle to a regulator supply to PHY core block.
> + - vdda-pll-supply: Phandle to 1.8V regulator supply to PHY refclk pll block.
> +
> +Optional properties:
> + - vddp-ref-clk-supply: Phandle to a regulator supply to any specific refclk
> + pll block.
> +
> +Example:
> + pcie_phy: pciephy@34000 {

pcie-phy or just phy as the node name?

--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project

\
 
 \ /
  Last update: 2016-11-28 23:56    [W:0.157 / U:0.948 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site