lkml.org 
[lkml]   [2014]   [Aug]   [29]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 0/5] ARM: Berlin: Ethernet support
On 08/29/2014 03:50 PM, Antoine Tenart wrote:
> This series introduce the Marvell Berlin Ethernet driver, allowing to
> handle the fast Ethernet port. This driver is based on the mv643xx_eth
> driver and reuse some of its functions. While I wanted to make these
> functions common to the two drivers at first, I finally do think this
> is not a great idea:
> - Registers are very different.
> - The mv643xx_eth supports up to 1000Mbps interfaces and performance
> issues may occur, whereas the mvberlin_eth is only for fast Ethernet.
> - The mvberlin_eth driver uses a hash table to filter incoming packets.
> - A few other differences.
>
> I tried to stay close to the mv643xx_eth implementation, so that the
> discussion is still open, but I still ended up with lots of tiny
> differences that can be hard to manage for both cases. In the end I do
> think having two separate drivers is a good choice.

Antoine,

first of all, thanks a lot for providing this driver! I checked the
usual Marvell datasheets to see where the ethernet IP in Berlin comes
from and I hate to say it but it very much looks like PXA168, see [1]
A.22. Also, there is already a driver for pxa168_eth available.

I'll test and review you current driver on BG2 asap, but I guess it
should be merged with pxa168_eth _if_ the registers are really
compatible.

Sebastian

[1]
http://www.marvell.com/application-processors/armada-100/assets/armada_16x_software_manual.pdf

> That being said, I tested the Ethernet communication with ICMP pings,
> netcat, tried to use some network related softwares (such as ssh). Here
> is an iperf output:
>
> ------------------------------------------------------------
> Client connecting to 192.168.0.11, TCP port 5001
> TCP window size: 85.0 KByte (default)
> ------------------------------------------------------------
> [ 3] local 192.168.0.20 port 44183 connected with 192.168.0.11 port 5001
> [ ID] Interval Transfer Bandwidth
> [ 3] 0.0-10.0 sec 113 MBytes 94.8 Mbits/sec
>
> Tests were done on a BG2Q DMP, and this series currently does not add
> other device tree nodes than the ones for this board.
>
> Thanks!
>
> Antoine
>
>
> Antoine Tenart (5):
> net: mvberlin_eth: add an Ethernet driver for Marvell Berlin
> Documentation: bindings: net: add the Marvell Berlin Ethernet
> controller
> Documentation: devicetree: net: mention Marvell Berlin
> ARM: dts: berlin: add ethernet and mdio nodes
> ARM: dts: berlin: enable the Ethernet port on the BG2Q DMP
>
> .../devicetree/bindings/net/marvell-berlin.txt | 23 +
> .../devicetree/bindings/net/marvell-orion-mdio.txt | 6 +-
> arch/arm/boot/dts/berlin2q-marvell-dmp.dts | 13 +
> arch/arm/boot/dts/berlin2q.dtsi | 19 +
> drivers/net/ethernet/marvell/Kconfig | 9 +
> drivers/net/ethernet/marvell/Makefile | 1 +
> drivers/net/ethernet/marvell/mvberlin_eth.c | 2081 ++++++++++++++++++++
> 7 files changed, 2149 insertions(+), 3 deletions(-)
> create mode 100644 Documentation/devicetree/bindings/net/marvell-berlin.txt
> create mode 100644 drivers/net/ethernet/marvell/mvberlin_eth.c
>



\
 
 \ /
  Last update: 2014-08-29 19:01    [W:2.486 / U:0.012 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site