lkml.org 
[lkml]   [2014]   [May]   [16]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH] pinctrl: baytrail: Add pull type, strength and open drain to debugfs output
Date
In case of resolving power management or similar issues it might be useful
to have these properties included in the debugfs output.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
---
drivers/pinctrl/pinctrl-baytrail.c | 55 +++++++++++++++++++++++++++++++++++---
1 file changed, 51 insertions(+), 4 deletions(-)

diff --git a/drivers/pinctrl/pinctrl-baytrail.c b/drivers/pinctrl/pinctrl-baytrail.c
index 7c65c9dab215..975572e2f260 100644
--- a/drivers/pinctrl/pinctrl-baytrail.c
+++ b/drivers/pinctrl/pinctrl-baytrail.c
@@ -43,9 +43,20 @@
#define BYT_INT_STAT_REG 0x800

/* BYT_CONF0_REG register bits */
+#define BYT_IODEN BIT(31)
#define BYT_TRIG_NEG BIT(26)
#define BYT_TRIG_POS BIT(25)
#define BYT_TRIG_LVL BIT(24)
+#define BYT_PULL_STR_SHIFT 9
+#define BYT_PULL_STR_MASK (3 << BYT_PULL_STR_SHIFT)
+#define BYT_PULL_STR_2K (0 << BYT_PULL_STR_SHIFT)
+#define BYT_PULL_STR_10K (1 << BYT_PULL_STR_SHIFT)
+#define BYT_PULL_STR_20K (2 << BYT_PULL_STR_SHIFT)
+#define BYT_PULL_STR_40K (3 << BYT_PULL_STR_SHIFT)
+#define BYT_PULL_ASSIGN_SHIFT 7
+#define BYT_PULL_ASSIGN_MASK (3 << BYT_PULL_ASSIGN_SHIFT)
+#define BYT_PULL_ASSIGN_UP (1 << BYT_PULL_ASSIGN_SHIFT)
+#define BYT_PULL_ASSIGN_DOWN (2 << BYT_PULL_ASSIGN_SHIFT)
#define BYT_PIN_MUX 0x07

/* BYT_VAL_REG register bits */
@@ -321,6 +332,8 @@ static void byt_gpio_dbg_show(struct seq_file *s, struct gpio_chip *chip)
spin_lock_irqsave(&vg->lock, flags);

for (i = 0; i < vg->chip.ngpio; i++) {
+ const char *pull_str = NULL;
+ const char *pull = NULL;
const char *label;
offs = vg->range->pins[i] * 16;
conf0 = readl(vg->reg_base + offs + BYT_CONF0_REG);
@@ -330,8 +343,32 @@ static void byt_gpio_dbg_show(struct seq_file *s, struct gpio_chip *chip)
if (!label)
label = "Unrequested";

+ switch (conf0 & BYT_PULL_ASSIGN_MASK) {
+ case BYT_PULL_ASSIGN_UP:
+ pull = "up";
+ break;
+ case BYT_PULL_ASSIGN_DOWN:
+ pull = "down";
+ break;
+ }
+
+ switch (conf0 & BYT_PULL_STR_MASK) {
+ case BYT_PULL_STR_2K:
+ pull_str = "2k";
+ break;
+ case BYT_PULL_STR_10K:
+ pull_str = "10k";
+ break;
+ case BYT_PULL_STR_20K:
+ pull_str = "20k";
+ break;
+ case BYT_PULL_STR_40K:
+ pull_str = "40k";
+ break;
+ }
+
seq_printf(s,
- " gpio-%-3d (%-20.20s) %s %s %s pad-%-3d offset:0x%03x mux:%d %s%s%s\n",
+ " gpio-%-3d (%-20.20s) %s %s %s pad-%-3d offset:0x%03x mux:%d %s%s%s",
i,
label,
val & BYT_INPUT_EN ? " " : "in",
@@ -339,9 +376,19 @@ static void byt_gpio_dbg_show(struct seq_file *s, struct gpio_chip *chip)
val & BYT_LEVEL ? "hi" : "lo",
vg->range->pins[i], offs,
conf0 & 0x7,
- conf0 & BYT_TRIG_NEG ? " fall" : "",
- conf0 & BYT_TRIG_POS ? " rise" : "",
- conf0 & BYT_TRIG_LVL ? " level" : "");
+ conf0 & BYT_TRIG_NEG ? " fall" : " ",
+ conf0 & BYT_TRIG_POS ? " rise" : " ",
+ conf0 & BYT_TRIG_LVL ? " level" : " ");
+
+ if (pull && pull_str)
+ seq_printf(s, " %-4s %-3s", pull, pull_str);
+ else
+ seq_puts(s, " ");
+
+ if (conf0 & BYT_IODEN)
+ seq_puts(s, " open-drain");
+
+ seq_puts(s, "\n");
}
spin_unlock_irqrestore(&vg->lock, flags);
}
--
2.0.0.rc2


\
 
 \ /
  Last update: 2014-05-16 12:01    [W:0.107 / U:0.036 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site