lkml.org 
[lkml]   [2013]   [Jun]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 6/9] hpsa: rework pci pm related code for simplification
Date
Use pci core pm interface to simplify code.

Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: "Stephen M. Cameron" <scameron@beardog.cce.hp.com>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Cc: iss_storagedev@hp.com
Cc: linux-scsi@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
---
drivers/scsi/hpsa.c | 16 +++-------------
1 files changed, 3 insertions(+), 13 deletions(-)

diff --git a/drivers/scsi/hpsa.c b/drivers/scsi/hpsa.c
index 7f4f790..f5ba6d4 100644
--- a/drivers/scsi/hpsa.c
+++ b/drivers/scsi/hpsa.c
@@ -3753,9 +3753,6 @@ static int hpsa_message(struct pci_dev *pdev, unsigned char opcode,
static int hpsa_controller_hard_reset(struct pci_dev *pdev,
void * __iomem vaddr, u32 use_doorbell)
{
- u16 pmcsr;
- int pos;
-
if (use_doorbell) {
/* For everything after the P600, the PCI power state method
* of resetting the controller doesn't work, so we have this
@@ -3773,8 +3770,7 @@ static int hpsa_controller_hard_reset(struct pci_dev *pdev,
* this causes a secondary PCI reset which will reset the
* controller." */

- pos = pci_find_capability(pdev, PCI_CAP_ID_PM);
- if (pos == 0) {
+ if (!pdev->pm_cap) {
dev_err(&pdev->dev,
"hpsa_reset_controller: "
"PCI PM not supported\n");
@@ -3782,18 +3778,12 @@ static int hpsa_controller_hard_reset(struct pci_dev *pdev,
}
dev_info(&pdev->dev, "using PCI PM to reset controller\n");
/* enter the D3hot power management state */
- pci_read_config_word(pdev, pos + PCI_PM_CTRL, &pmcsr);
- pmcsr &= ~PCI_PM_CTRL_STATE_MASK;
- pmcsr |= PCI_D3hot;
- pci_write_config_word(pdev, pos + PCI_PM_CTRL, pmcsr);
+ pci_set_power_state(pdev, PCI_D3hot);

msleep(500);

/* enter the D0 power management state */
- pmcsr &= ~PCI_PM_CTRL_STATE_MASK;
- pmcsr |= PCI_D0;
- pci_write_config_word(pdev, pos + PCI_PM_CTRL, pmcsr);
-
+ pci_set_power_state(pdev, PCI_D0);
/*
* The P600 requires a small delay when changing states.
* Otherwise we may think the board did not reset and we bail.
--
1.7.1



\
 
 \ /
  Last update: 2013-06-18 11:01    [W:0.033 / U:0.996 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site