lkml.org 
[lkml]   [2012]   [Jun]   [19]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH V2 2/3] staging/rtl8192u: fix coding style problems
Date
fixed some of the C99 warnings and coding style problems,
not only reported checkpatch but while reading the code

Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
---
drivers/staging/rtl8192u/r8180_93cx6.c | 25 ++++++++++++++-----------
1 file changed, 14 insertions(+), 11 deletions(-)

diff --git a/drivers/staging/rtl8192u/r8180_93cx6.c b/drivers/staging/rtl8192u/r8180_93cx6.c
index 19f5270..a72bbd4 100644
--- a/drivers/staging/rtl8192u/r8180_93cx6.c
+++ b/drivers/staging/rtl8192u/r8180_93cx6.c
@@ -80,7 +80,7 @@ void eprom_send_bits_string(struct net_device *dev, short b[], int len)
{
int i;

- for(i=0; i<len; i++){
+ for (i = 0; i < len; i++) {
eprom_w(dev, b[i]);
eprom_ck_cycle(dev);
}
@@ -90,14 +90,13 @@ void eprom_send_bits_string(struct net_device *dev, short b[], int len)
u32 eprom_read(struct net_device *dev, u32 addr)
{
struct r8192_priv *priv = ieee80211_priv(dev);
- short read_cmd[]={1,1,0};
+ short read_cmd[] = {1, 1, 0};
short addr_str[8];
int i;
int addr_len;
- u32 ret;
+ u32 ret = 0;

- ret=0;
- //enable EPROM programming
+ /* enable EPROM programming */
write_nic_byte_E(dev, EPROM_CMD,
(EPROM_CMD_PROGRAM<<EPROM_CMD_OPERATING_MODE_SHIFT));
force_pci_posting(dev);
@@ -127,13 +126,17 @@ u32 eprom_read(struct net_device *dev, u32 addr)
eprom_send_bits_string(dev, read_cmd, 3);
eprom_send_bits_string(dev, addr_str, addr_len);

- //keep chip pin D to low state while reading.
- //I'm unsure if it is necessary, but anyway shouldn't hurt
+ /**
+ * keep chip pin D to low state while reading.
+ * I'm unsure if it is necessary, but anyway shouldn't hurt
+ */
eprom_w(dev, 0);

- for(i=0;i<16;i++){
- //eeprom needs a clk cycle between writing opcode&adr
- //and reading data. (eeprom outs a dummy 0)
+ for (i = 0; i < 16; i++) {
+ /**
+ * eeprom needs a clk cycle between writing opcode&adr
+ * and reading data. (eeprom outs a dummy 0)
+ */
eprom_ck_cycle(dev);
ret |= (eprom_r(dev)<<(15-i));
}
@@ -141,7 +144,7 @@ u32 eprom_read(struct net_device *dev, u32 addr)
eprom_cs(dev, 0);
eprom_ck_cycle(dev);

- //disable EPROM programming
+ /* disable EPROM programming */
write_nic_byte_E(dev, EPROM_CMD,
(EPROM_CMD_NORMAL<<EPROM_CMD_OPERATING_MODE_SHIFT));
return ret;
--
1.7.9.5


\
 
 \ /
  Last update: 2012-06-19 21:41    [W:0.027 / U:0.464 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site