lkml.org 
[lkml]   [2012]   [Oct]   [2]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH] mfd: spelling/cleanup of twl4030 madc
Date
From: Peter Meerwald <p.meerwald@bct-electronic.com>

fixe typos in comments and correct trivial debug output

Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
---
drivers/mfd/twl4030-madc.c | 24 ++++++++++++------------
1 file changed, 12 insertions(+), 12 deletions(-)

diff --git a/drivers/mfd/twl4030-madc.c b/drivers/mfd/twl4030-madc.c
index 456ecb5..dfacf6c 100644
--- a/drivers/mfd/twl4030-madc.c
+++ b/drivers/mfd/twl4030-madc.c
@@ -86,13 +86,13 @@ twl4030_divider_ratios[16] = {
{15, 100}, /* CHANNEL 11 */
{1, 4}, /* CHANNEL 12 */
{1, 1}, /* CHANNEL 13 Reserved channels */
- {1, 1}, /* CHANNEL 14 Reseved channels */
+ {1, 1}, /* CHANNEL 14 Reserved channels */
{5, 11}, /* CHANNEL 15 */
};


/*
- * Conversion table from -3 to 55 degree Celcius
+ * Conversion table from -3 to 55 degree Celsius
*/
static int therm_tbl[] = {
30800, 29500, 28300, 27100,
@@ -107,8 +107,8 @@ static int therm_tbl[] = {
/*
* Structure containing the registers
* of different conversion methods supported by MADC.
- * Hardware or RT real time conversion request initiated by external host
- * processor for RT Signal conversions.
+ * Hardware or RT (real time) conversion request initiated by external host
+ * processor for RT signal conversions.
* External host processors can also request for non RT conversions
* SW1 and SW2 software conversions also called asynchronous or GPC request.
*/
@@ -209,7 +209,7 @@ static int twl4030battery_current(int raw_volt)
* Function to read channel values
* @madc - pointer to twl4030_madc_data struct
* @reg_base - Base address of the first channel
- * @Channels - 16 bit bitmap. If the bit is set, channel value is read
+ * @channels - 16 bit bitmap. If the bit is set, channel value is read
* @buf - The channel values are stored here. if read fails error
* value is stored
* Returns the number of successfully read channels.
@@ -360,7 +360,7 @@ static irqreturn_t twl4030_madc_threaded_irq_handler(int irq, void *_madc)
continue;
ret = twl4030_madc_disable_irq(madc, i);
if (ret < 0)
- dev_dbg(madc->dev, "Disable interrupt failed%d\n", i);
+ dev_dbg(madc->dev, "Disable interrupt %d failed\n", i);
madc->requests[i].result_pending = 1;
}
for (i = 0; i < TWL4030_MADC_NUM_METHODS; i++) {
@@ -536,7 +536,7 @@ int twl4030_madc_conversion(struct twl4030_madc_request *req)
ret = twl_i2c_write_u8(TWL4030_MODULE_MADC, ch_lsb, method->sel);
if (ret) {
dev_err(twl4030_madc->dev,
- "unable to write sel register 0x%X\n", method->sel + 1);
+ "unable to write sel register 0x%X\n", method->sel);
goto out;
}
/* Select averaging for all channels if do_avg is set */
@@ -553,8 +553,8 @@ int twl4030_madc_conversion(struct twl4030_madc_request *req)
ch_lsb, method->avg);
if (ret) {
dev_err(twl4030_madc->dev,
- "unable to write sel reg 0x%X\n",
- method->sel + 1);
+ "unable to write avg register 0x%X\n",
+ method->avg);
goto out;
}
}
@@ -660,7 +660,7 @@ static int twl4030_madc_set_current_generator(struct twl4030_madc_data *madc,
/*
* Function that sets MADC software power on bit to enable MADC
* @madc - pointer to twl4030_madc_data struct
- * @on - Enable or disable MADC software powen on bit.
+ * @on - Enable or disable MADC software power on bit.
* returns error if i2c read/write fails else 0
*/
static int twl4030_madc_set_power(struct twl4030_madc_data *madc, int on)
@@ -728,7 +728,7 @@ static int __devinit twl4030_madc_probe(struct platform_device *pdev)
ret = twl_i2c_read_u8(TWL4030_MODULE_MAIN_CHARGE,
&regval, TWL4030_BCI_BCICTL1);
if (ret) {
- dev_err(&pdev->dev, "unable to read reg BCI CTL1 0x%X\n",
+ dev_err(&pdev->dev, "unable to read reg BCICTL1 0x%X\n",
TWL4030_BCI_BCICTL1);
goto err_i2c;
}
@@ -736,7 +736,7 @@ static int __devinit twl4030_madc_probe(struct platform_device *pdev)
ret = twl_i2c_write_u8(TWL4030_MODULE_MAIN_CHARGE,
regval, TWL4030_BCI_BCICTL1);
if (ret) {
- dev_err(&pdev->dev, "unable to write reg BCI Ctl1 0x%X\n",
+ dev_err(&pdev->dev, "unable to write reg BCICTL1 0x%X\n",
TWL4030_BCI_BCICTL1);
goto err_i2c;
}
--
1.7.9.5


\
 
 \ /
  Last update: 2012-10-02 18:41    [W:0.027 / U:0.472 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site