lkml.org 
[lkml]   [2011]   [Feb]   [7]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH] ide: legacy VLB drivers housekeeping
Date
* remove stale documentation
* remove dead ALWAYS_SET_DTC2278_PIO_MODE code from dtc2278
* remove legacy debugging code from ht6560b

There should be no functional changes caused by this patch.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
---
drivers/ide/ali14xx.c | 28 +----------------
drivers/ide/dtc2278.c | 50 +++++++-------------------------
drivers/ide/ht6560b.c | 78
+-------------------------------------------------
drivers/ide/qd65xx.c | 43 ---------------------------
drivers/ide/umc8672.c | 20 ------------
5 files changed, 17 insertions(+), 202 deletions(-)

Index: b/drivers/ide/ali14xx.c
===================================================================
--- a/drivers/ide/ali14xx.c
+++ b/drivers/ide/ali14xx.c
@@ -7,32 +7,7 @@
*
* Works for ALI M1439/1443/1445/1487/1489 chipsets.
*
- * Adapted from code developed by derekn@vw.ece.cmu.edu. -ml
- * Derek's notes follow:
- *
- * I think the code should be pretty understandable,
- * but I'll be happy to (try to) answer questions.
- *
- * The critical part is in the setupDrive function. The initRegisters
- * function doesn't seem to be necessary, but the DOS driver does it, so
- * I threw it in.
- *
- * I've only tested this on my system, which only has one disk. I posted
- * it to comp.sys.linux.hardware, so maybe some other people will try it
- * out.
- *
- * Derek Noonburg (derekn@ece.cmu.edu)
- * 95-sep-26
- *
- * Update 96-jul-13:
- *
- * I've since upgraded to two disks and a CD-ROM, with no trouble, and
- * I've also heard from several others who have used it successfully.
- * This driver appears to work with both the 1443/1445 and the 1487/1489
- * chipsets. I've added support for PIO mode 4 for the 1487. This
- * seems to work just fine on the 1443 also, although I'm not sure it's
- * advertised as supporting mode 4. (I've been running a WDC AC21200 in
- * mode 4 for a while now with no trouble.) -Derek
+ * Adapted from code developed by Derek Noonburg <derekn@vw.ece.cmu.edu>. -
ml
*/

#include <linux/module.h>
@@ -177,6 +152,7 @@ static int __init findPort(void)

/*
* Initialize controller registers with default values.
+ * (doesn't seem to be necessary but the DOS driver does it).
*/
static int __init initRegisters(void)
{
Index: b/drivers/ide/dtc2278.c
===================================================================
--- a/drivers/ide/dtc2278.c
+++ b/drivers/ide/dtc2278.c
@@ -2,6 +2,17 @@
* Copyright (C) 1996 Linus Torvalds & author (see below)
*/

+/*
+ * Initial DTC-2278 support from Dyan Wile <andy@cercle.cts.com>.
+ */
+
+/*
+ * DTC2278S has only a single IDE interface
+ * DTC2278D has two IDE interfaces and is otherwise identical to the S
version
+ * DTC2278E also has serial ports and a printer port
+ * DTC2278EB: has onboard BIOS
+ */
+
#include <linux/module.h>
#include <linux/types.h>
#include <linux/kernel.h>
@@ -17,37 +28,6 @@

#define DRV_NAME "dtc2278"

-/*
- * Changing this #undef to #define may solve start up problems in some
systems.
- */
-#undef ALWAYS_SET_DTC2278_PIO_MODE
-
-/*
- * From: andy@cercle.cts.com (Dyan Wile)
- *
- * Below is a patch for DTC-2278 - alike software-programmable controllers
- * The code enables the secondary IDE controller and the PIO4 (3?) timings on
- * the primary (EIDE). You may probably have to enable the 32-bit support to
- * get the full speed. You better get the disk interrupts disabled ( hdparm -
u0
- * /dev/hd.. ) for the drives connected to the EIDE interface. (I get my
- * filesystem corrupted with -u1, but under heavy disk load only :-)
- *
- * This card is now forced to use the "serialize" feature,
- * and irq-unmasking is disallowed. If io_32bit is enabled,
- * it must be done for BOTH drives on each interface.
- *
- * This code was written for the DTC2278E, but might work with any of these:
- *
- * DTC2278S has only a single IDE interface.
- * DTC2278D has two IDE interfaces and is otherwise identical to the S
version.
- * DTC2278E also has serial ports and a printer port
- * DTC2278EB: has onboard BIOS, and "works like a charm" -- Kent Bradford
<kent@theory.caltech.edu>
- *
- * There may be a fourth controller type. The S and D versions use the
- * Winbond chip, and I think the E version does also.
- *
- */
-
static void sub22 (char b, char c)
{
int i;
@@ -117,14 +97,6 @@ static int __init dtc2278_probe(void)
inb(0x3f6);
outb_p(0x20,0xb4);
inb(0x3f6);
-#ifdef ALWAYS_SET_DTC2278_PIO_MODE
- /*
- * This enables PIO mode4 (3?) on the first interface
- * and may solve start-up problems for some people.
- */
- sub22(1,0xc3);
- sub22(0,0xa0);
-#endif
local_irq_restore(flags);

return ide_legacy_device_add(&dtc2278_port_info, 0);
Index: b/drivers/ide/ht6560b.c
===================================================================
--- a/drivers/ide/ht6560b.c
+++ b/drivers/ide/ht6560b.c
@@ -4,8 +4,6 @@

/*
* HT-6560B EIDE-controller support
- * To activate controller support use kernel parameter "ide0=ht6560b".
- * Use hdparm utility to enable PIO mode support.
*
* Author: Mikko Ala-Fossi <maf@iki.fi>
* Jan Evert van Grootheest <j.e.van.grootheest@caiway.nl>
@@ -28,8 +26,6 @@

#include <asm/io.h>

-/* #define DEBUG */ /* remove comments for DEBUG messages */
-
/*
* The special i/o-port that HT-6560B uses to configuration:
* bit0 (0x01): "1" selects secondary interface
@@ -53,47 +49,9 @@ static inline u8 HT_CONFIG(ide_drive_t *
* FIFO + PREFETCH (both a/b-model)
*/
#define HT_CONFIG_DEFAULT 0x1c /* no prefetch */
-/* #define HT_CONFIG_DEFAULT 0x3c */ /* with prefetch */
#define HT_SECONDARY_IF 0x01
#define HT_PREFETCH_MODE 0x20

-/*
- * ht6560b Timing values:
- *
- * I reviewed some assembler source listings of htide drivers and found
- * out how they setup those cycle time interfacing values, as they at Holtek
- * call them. IDESETUP.COM that is supplied with the drivers figures out
- * optimal values and fetches those values to drivers. I found out that
- * they use Select register to fetch timings to the ide board right after
- * interface switching. After that it was quite easy to add code to
- * ht6560b.c.
- *
- * IDESETUP.COM gave me values 0x24, 0x45, 0xaa, 0xff that worked fine
- * for hda and hdc. But hdb needed higher values to work, so I guess
- * that sometimes it is necessary to give higher value than IDESETUP
- * gives. [see cmd640.c for an extreme example of this. -ml]
- *
- * Perhaps I should explain something about these timing values:
- * The higher nibble of value is the Recovery Time (rt) and the lower nibble
- * of the value is the Active Time (at). Minimum value 2 is the fastest and
- * the maximum value 15 is the slowest. Default values should be 15 for both.
- * So 0x24 means 2 for rt and 4 for at. Each of the drives should have
- * both values, and IDESETUP gives automatically rt=15 st=15 for CDROMs or
- * similar. If value is too small there will be all sorts of failures.
- *
- * Timing byte consists of
- * High nibble: Recovery Cycle Time (rt)
- * The valid values range from 2 to 15. The default is 15.
- *
- * Low nibble: Active Cycle Time (at)
- * The valid values range from 2 to 15. The default is 15.
- *
- * You can obtain optimized timing values by running Holtek IDESETUP.COM
- * for DOS. DOS drivers get their timing values from command line, where
- * the first value is the Recovery Time and the second value is the
- * Active Time for each drive. Smaller value gives higher speed.
- * In case of failures you should probably fall back to a higher value.
- */
static inline u8 HT_TIMING(ide_drive_t *drive)
{
return (unsigned long)ide_get_drivedata(drive) & 0x00ff;
@@ -107,10 +65,6 @@ static inline u8 HT_TIMING(ide_drive_t *
* The HT-6560B can only enable one IDE port at a time, and requires a
* silly sequence (below) whenever we switch between primary and secondary.
*/
-
-/*
- * This routine is invoked from ide.c to prepare for access to a given drive.
- */
static void ht6560b_dev_select(ide_drive_t *drive)
{
ide_hwif_t *hwif = drive->hwif;
@@ -145,10 +99,6 @@ static void ht6560b_dev_select(ide_drive
*/
outb(timing, hwif->io_ports.device_addr);
(void)inb(hwif->io_ports.status_addr);
-#ifdef DEBUG
- printk("ht6560b: %s: select=%#x timing=%#x\n",
- drive->name, select, timing);
-#endif
}
local_irq_restore(flags);

@@ -187,11 +137,7 @@ static int __init try_to_init_ht6560b(vo
(void)inb(0x1f7); /* Status register */

printk("ht6560b " HT6560B_VERSION
- ": chipset detected and initialized"
-#ifdef DEBUG
- " with debug enabled"
-#endif
- "\n"
+ ": chipset detected and initialized\n"
);
return 1;
}
@@ -227,20 +173,10 @@ static u8 ht_pio2timings(ide_drive_t *dr
if (recovery_cycles < 2) recovery_cycles = 2;
if (active_cycles > 15) active_cycles = 15;
if (recovery_cycles > 15) recovery_cycles = 0; /* 0==16 */
-
-#ifdef DEBUG
- printk("ht6560b: drive %s setting pio=%d recovery=%d (%dns)
active=%d (%dns)\n", drive->name, pio, recovery_cycles, recovery_time,
active_cycles, active_time);
-#endif
-
+
return (u8)((recovery_cycles << 4) | active_cycles);
- } else {
-
-#ifdef DEBUG
- printk("ht6560b: drive %s setting pio=0\n", drive->name);
-#endif
-
+ } else
return HT_TIMING_DEFAULT; /* default setting */
- }
}

static DEFINE_SPINLOCK(ht6560b_lock);
@@ -272,10 +208,6 @@ static void ht_set_prefetch(ide_drive_t
ide_set_drivedata(drive, (void *)config);

spin_unlock_irqrestore(&ht6560b_lock, flags);
-
-#ifdef DEBUG
- printk("ht6560b: drive %s prefetch mode %sabled\n", drive->name, (state ?
"en" : "dis"));
-#endif
}

static void ht6560b_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
@@ -299,10 +231,6 @@ static void ht6560b_set_pio_mode(ide_hwi
config |= timing;
ide_set_drivedata(drive, (void *)config);
spin_unlock_irqrestore(&ht6560b_lock, flags);
-
-#ifdef DEBUG
- printk("ht6560b: drive %s tuned to pio mode %#x timing=%#x\n", drive-
>name, pio, timing);
-#endif
}

static void __init ht6560b_init_dev(ide_drive_t *drive)
Index: b/drivers/ide/qd65xx.c
===================================================================
--- a/drivers/ide/qd65xx.c
+++ b/drivers/ide/qd65xx.c
@@ -3,15 +3,7 @@
*/

/*
- * Version 0.03 Cleaned auto-tune, added probe
- * Version 0.04 Added second channel tuning
- * Version 0.05 Enhanced tuning ; added qd6500 support
- * Version 0.06 Added dos driver's list
- * Version 0.07 Second channel bug fix
- *
* QDI QD6500/QD6580 EIDE controller fast support
- *
- * To activate controller support, use "ide0=qd65xx"
*/

/*
@@ -47,41 +39,6 @@
* http://www.ryston.cz/petr/vlb
*/

-/*
- * base: Timer1
- *
- *
- * base+0x01: Config (R/O)
- *
- * bit 0: ide baseport: 1 = 0x1f0 ; 0 = 0x170 (only useful for qd6500)
- * bit 1: qd65xx baseport: 1 = 0xb0 ; 0 = 0x30
- * bit 2: ID3: bus speed: 1 = <=33MHz ; 0 = >33MHz
- * bit 3: qd6500: 1 = disabled, 0 = enabled
- * qd6580: 1
- * upper nibble:
- * qd6500: 1100
- * qd6580: either 1010 or 0101
- *
- *
- * base+0x02: Timer2 (qd6580 only)
- *
- *
- * base+0x03: Control (qd6580 only)
- *
- * bits 0-3 must always be set 1
- * bit 4 must be set 1, but is set 0 by dos driver while measuring vlb clock
- * bit 0 : 1 = Only primary port enabled : channel 0 for hda, channel 1 for
hdb
- * 0 = Primary and Secondary ports enabled : channel 0 for hda & hdb
- * channel 1 for hdc & hdd
- * bit 1 : 1 = only disks on primary port
- * 0 = disks & ATAPI devices on primary port
- * bit 2-4 : always 0
- * bit 5 : status, but of what ?
- * bit 6 : always set 1 by dos driver
- * bit 7 : set 1 for non-ATAPI devices on primary port
- * (maybe read-ahead and post-write buffer ?)
- */
-
static int timings[4]={-1,-1,-1,-1}; /* stores current timing for each timer
*/

/*
Index: b/drivers/ide/umc8672.c
===================================================================
--- a/drivers/ide/umc8672.c
+++ b/drivers/ide/umc8672.c
@@ -5,8 +5,7 @@
/*
* Principal Author/Maintainer: PODIEN@hml2.atlas.de (Wolfram Podien)
*
- * This file provides support for the advanced features
- * of the UMC 8672 IDE interface.
+ * UMC 8672 IDE interface
*
* Version 0.01 Initial version, hacked out of ide.c,
* and #include'd rather than compiled separately.
@@ -18,23 +17,6 @@
* add detection of possible race condition -ml
*/

-/*
- * VLB Controller Support from
- * Wolfram Podien
- * Rohoefe 3
- * D28832 Achim
- * Germany
- *
- * To enable UMC8672 support there must a lilo line like
- * append="ide0=umc8672"...
- * To set the speed according to the abilities of the hardware there must be
a
- * line like
- * #define UMC_DRIVE0 11
- * in the beginning of the driver, which sets the speed of drive 0 to 11
(there
- * are some lines present). 0 - 11 are allowed speed values. These values are
- * the results from the DOS speed test program supplied from UMC. 11 is the
- * highest speed (about PIO mode 3)
- */
#define REALLY_SLOW_IO /* some systems can safely undef this */

#include <linux/module.h>

\
 
 \ /
  Last update: 2011-02-07 12:01    [W:0.443 / U:0.008 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site