Messages in this thread | | | Date | Thu, 24 Jul 2008 09:05:09 +0930 | From | Kevin Shanahan <> | Subject | libata timeout, MCE and kernel panic |
| |
Hi,
I had a server reboot overnight (still need to find the cause of that, nothing in the logs but I suspect OOM cause by our apache setup), but encountered another problem when I tried to bring it back up this morning.
The system has a RAID5 array with four 400GB SATA disks, which it noticed was dirty so reconstruction began. This raid device is an lvm pv, with several ext3 filesystems. When the init scripts went to mount the largest filesystem (approx 650GB, about 85% full I think), journal recovery was required. It seems the journal recovery combined with the md device reconstruction was enough to cause an ata command timeout. After that I saw several MCEs and the kernel paniced.
I don't have a serial console handy atm, so I just took a photo of the console: http://disenchant.net/tmp/dsc00028.jpg
I've since got the server back up again by preventing that fs from mounting at boot time. Is this a bug of some kind, or have just dumbly misconfigured something? Full dmesg below.
TIA, Kevin. --
Linux version 2.6.25.10 (kmshanah@debian) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 SMP PREEMPT Fri Jul 11 12:49:53 CST 2008 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009e800 (usable) BIOS-e820: 000000000009e800 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 00000000dfcf0000 (usable) BIOS-e820: 00000000dfcf0000 - 00000000dfd96000 (ACPI NVS) BIOS-e820: 00000000dfd96000 - 00000000dfdfd000 (usable) BIOS-e820: 00000000dfdfd000 - 00000000dfe5f000 (reserved) BIOS-e820: 00000000dfe5f000 - 00000000dfe68000 (usable) BIOS-e820: 00000000dfe68000 - 00000000dfedf000 (ACPI NVS) BIOS-e820: 00000000dfedf000 - 00000000dfee5000 (usable) BIOS-e820: 00000000dfee5000 - 00000000dfeff000 (ACPI data) BIOS-e820: 00000000dfeff000 - 00000000dff00000 (usable) BIOS-e820: 00000000dff00000 - 00000000e0000000 (reserved) BIOS-e820: 00000000f0000000 - 00000000f4000000 (reserved) BIOS-e820: 00000000fff80000 - 00000000fff8c000 (reserved) BIOS-e820: 0000000100000000 - 0000000120000000 (usable) Warning only 4GB will be used. Use a HIGHMEM64G enabled kernel. 3200MB HIGHMEM available. 896MB LOWMEM available. Scan SMP from c0000000 for 1024 bytes. Scan SMP from c009fc00 for 1024 bytes. Scan SMP from c00f0000 for 65536 bytes. found SMP MP-table at [c00fd270] 000fd270 Entering add_active_range(0, 0, 1048576) 0 entries of 256 used Zone PFN ranges: DMA 0 -> 4096 Normal 4096 -> 229376 HighMem 229376 -> 1048576 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0 -> 1048576 On node 0 totalpages: 1048576 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4064 pages, LIFO batch:0 Normal zone: 1760 pages used for memmap Normal zone: 223520 pages, LIFO batch:31 HighMem zone: 6400 pages used for memmap HighMem zone: 812800 pages, LIFO batch:31 Movable zone: 0 pages used for memmap DMI 2.5 present. ACPI: RSDP 000F03C0, 0024 (r2 INTEL ) ACPI: XSDT DFEFE120, 00AC (r1 INTEL S3200SHC 0 INTL 1000013) ACPI: SLIC DFEFC000, 0176 (r1 INTEL S3200SHC 2 INTL 1000013) ACPI: FACP DFEFA000, 00F4 (r3 INTEL S3200SHC 0 MSFT 1000013) ACPI: DSDT DFEF4000, 568D (r1 INTEL S3200SHC 0 MSFT 1000013) ACPI: FACS DFE68000, 0040 ACPI: APIC DFEF3000, 0084 (r1 INTEL S3200SHC 0 MSFT 1000013) ACPI: WDDT DFEF2000, 0040 (r1 INTEL S3200SHC 0 MSFT 1000013) ACPI: MCFG DFEF1000, 003C (r1 INTEL S3200SHC 0 MSFT 1000013) ACPI: HPET DFEF0000, 0038 (r1 INTEL S3200SHC 1 MSFT 1000013) ACPI: SPCR DFEEF000, 0050 (r1 INTEL S3200SHC 0 MSFT 1000013) ACPI: DMAR DFEEE000, 0110 (r1 INTEL S3200SHC 1 MSFT 1000013) ACPI: SSDT DFEED000, 0175 (r1 INTEL Cpu0Ist 10 MSFT 1000013) ACPI: SSDT DFEEC000, 0175 (r1 INTEL Cpu1Ist 10 MSFT 1000013) ACPI: SSDT DFEEB000, 0175 (r1 INTEL Cpu2Ist 10 MSFT 1000013) ACPI: SSDT DFEEA000, 0175 (r1 INTEL Cpu3Ist 10 MSFT 1000013) ACPI: SSDT DFEE9000, 01BC (r1 INTEL CpuPm 10 MSFT 1000013) ACPI: HEST DFEE8000, 00A8 (r1 INTEL S3200SHC 1 INTL 1) ACPI: BERT DFEE7000, 0030 (r1 INTEL S3200SHC 1 INTL 1) ACPI: ERST DFEE6000, 0230 (r1 INTEL S3200SHC 1 INTL 1) ACPI: EINJ DFEE5000, 0130 (r1 INTEL S3200SHC 1 INTL 1) ACPI: PM-Timer IO Port: 0x408 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) Processor #0 6:15 APIC version 20 ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled) Processor #2 6:15 APIC version 20 ACPI: LAPIC (acpi_id[0x03] lapic_id[0x01] enabled) Processor #1 6:15 APIC version 20 ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled) Processor #3 6:15 APIC version 20 ACPI: LAPIC_NMI (acpi_id[0x01] high level lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x02] high level lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x03] high level lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x04] high level lint[0x1]) ACPI: IOAPIC (id[0x05] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 5, version 32, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Enabling APIC mode: Flat. Using 1 I/O APICs Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at e1000000 (gap: e0000000:10000000) Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1040384 Kernel command line: root=/dev/sda3 ro mapped APIC to ffffb000 (fee00000) mapped IOAPIC to ffffa000 (fec00000) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 4096 (order: 12, 16384 bytes) Detected 2394.075 MHz processor. Console: colour VGA+ 80x25 console [tty0] enabled Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 3627644k/4194304k available (2699k kernel code, 38600k reserved, 1527k data, 352k init, 2749852k highmem) virtual kernel memory layout: fixmap : 0xfff4d000 - 0xfffff000 ( 712 kB) pkmap : 0xff800000 - 0xffc00000 (4096 kB) vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB) lowmem : 0xc0000000 - 0xf8000000 ( 896 MB) .init : 0xc0528000 - 0xc0580000 ( 352 kB) .data : 0xc03a2eac - 0xc0520dbc (1527 kB) .text : 0xc0100000 - 0xc03a2eac (2699 kB) Checking if this processor honours the WP bit even in supervisor mode...Ok. CPA: page pool initialized 1 of 1 pages preallocated Calibrating delay using timer specific routine.. 4792.99 BogoMIPS (lpj=7983988) Mount-cache hash table entries: 512 CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 4096K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 0 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. using mwait in idle threads. Compat vDSO mapped to ffffe000. Checking 'hlt' instruction... OK. Freeing SMP alternatives: 14k freed ACPI: Core revision 20070126 CPU0: Intel(R) Xeon(R) CPU X3220 @ 2.40GHz stepping 0b Booting processor 1/1 ip 2000 Initializing CPU#1 Calibrating delay using timer specific routine.. 4789.21 BogoMIPS (lpj=7979550) CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 4096K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 1 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#1. CPU1: Intel(R) Xeon(R) CPU X3220 @ 2.40GHz stepping 0b Booting processor 2/2 ip 2000 Initializing CPU#2 Calibrating delay using timer specific routine.. 4789.24 BogoMIPS (lpj=7979589) CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 4096K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 2 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#2. CPU2: Intel(R) Xeon(R) CPU X3220 @ 2.40GHz stepping 0b Booting processor 3/3 ip 2000 Initializing CPU#3 Calibrating delay using timer specific routine.. 4789.24 BogoMIPS (lpj=7979592) CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 4096K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 3 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#3. CPU3: Intel(R) Xeon(R) CPU X3220 @ 2.40GHz stepping 0b Total of 4 processors activated (19161.69 BogoMIPS). ENABLING IO-APIC IRQs ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 checking TSC synchronization [CPU#0 -> CPU#1]: passed. checking TSC synchronization [CPU#0 -> CPU#2]: passed. checking TSC synchronization [CPU#0 -> CPU#3]: passed. Brought up 4 CPUs net_namespace: 452 bytes xor: automatically using best checksumming function: pIII_sse pIII_sse : 8846.400 MB/sec xor: using function: pIII_sse (8846.400 MB/sec) NET: Registered protocol family 16 No dock devices found. EISA bus registered ACPI: bus type pci registered PCI: Using MMCONFIG for extended config space PCI: Using configuration type 1 Setting up standard PCI resources ACPI: EC: Look up EC in DSDT ACPI: Interpreter enabled ACPI: (supports S0 S5) ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) pci 0000:00:1f.0: quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO pci 0000:00:1f.0: quirk: region 0500-053f claimed by ICH6 GPIO PCI: Transparent bridge - 0000:00:1e.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P32_._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 10 *11 12) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 *10 11 12) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 *9 10 11 12) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11 12) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 *11 12) ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 *10 11 12) ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 *9 10 11 12) ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 9 10 *11 12) Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init ACPI: bus type pnp registered pnp: PnP ACPI: found 14 devices ACPI: ACPI bus type pnp unregistered SCSI subsystem initialized libata version 3.00 loaded. usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report ACPI: RTC can wake from S4 system 00:01: iomem range 0xf0000000-0xf3ffffff could not be reserved system 00:01: iomem range 0xfeb00000-0xfeb03fff has been reserved system 00:01: iomem range 0xfed14000-0xfed17fff has been reserved system 00:01: iomem range 0xfed18000-0xfed18fff has been reserved system 00:01: iomem range 0xfed19000-0xfed19fff has been reserved system 00:01: iomem range 0xfed1c000-0xfed1ffff has been reserved system 00:01: iomem range 0xfed20000-0xfed3ffff has been reserved system 00:01: iomem range 0xfed45000-0xfed99fff has been reserved system 00:01: iomem range 0xc0000-0xdffff could not be reserved system 00:01: iomem range 0xe0000-0xfffff could not be reserved system 00:01: iomem range 0xffc00000-0xffffffff could not be reserved system 00:06: ioport range 0x500-0x53f has been reserved system 00:06: ioport range 0x400-0x47f has been reserved system 00:06: ioport range 0xca0-0xcaf has been reserved system 00:06: ioport range 0x680-0x6ff has been reserved system 00:06: ioport range 0x800-0x87f has been reserved system 00:06: ioport range 0x600-0x61f has been reserved PCI: Bridge: 0000:01:00.0 IO window: 2000-2fff MEM window: 0xe1a00000-0xe1afffff PREFETCH window: 0x00000000e1d00000-0x00000000e1dfffff PCI: Bridge: 0000:00:1c.0 IO window: 2000-2fff MEM window: 0xe1a00000-0xe1bfffff PREFETCH window: 0x00000000e1d00000-0x00000000e1dfffff PCI: Bridge: 0000:00:1c.4 IO window: disabled. MEM window: 0xe1000000-0xe18fffff PREFETCH window: 0x00000000e0000000-0x00000000e0ffffff PCI: Bridge: 0000:00:1e.0 IO window: 1000-1fff MEM window: 0xe1900000-0xe19fffff PREFETCH window: 0x00000000e1e00000-0x00000000e1efffff ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 17 PCI: Setting latency timer of device 0000:00:1c.0 to 64 ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:01:00.0 to 64 ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 17 (level, low) -> IRQ 17 PCI: Setting latency timer of device 0000:00:1c.4 to 64 PCI: Setting latency timer of device 0000:00:1e.0 to 64 NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 8, 1048576 bytes) TCP bind hash table entries: 65536 (order: 7, 524288 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered Machine check exception polling timer started. IA-32 Microcode Update Driver: v1.14a <tigran@aivazian.fsnet.co.uk> highmem bounce pool size: 64 pages VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) async_tx: api initialized (sync-only) io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) pci 0000:03:00.0: Boot video device PCI: Setting latency timer of device 0000:00:1c.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.0:pcie00] Allocate Port Service[0000:00:1c.0:pcie02] Allocate Port Service[0000:00:1c.0:pcie03] PCI: Setting latency timer of device 0000:00:1c.4 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.4:pcie00] Allocate Port Service[0000:00:1c.4:pcie02] Allocate Port Service[0000:00:1c.4:pcie03] input: Power Button (FF) as /class/input/input0 ACPI: Power Button (FF) [PWRF] input: Sleep Button (CM) as /class/input/input1 ACPI: Sleep Button (CM) [SLPB] input: Power Button (CM) as /class/input/input2 ACPI: Power Button (CM) [PWRB] ACPI: ACPI0007:00 is registered as cooling_device0 ACPI: ACPI0007:01 is registered as cooling_device1 ACPI: ACPI0007:02 is registered as cooling_device2 ACPI: ACPI0007:03 is registered as cooling_device3 isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found lp: driver loaded but no devices found Real Time Clock Driver v1.12ac ppdev: user-space parallel port driver Linux agpgart interface v0.103 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A 00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:08: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A FDC 0 is a National Semiconductor PC87306 brd: module loaded loop: module loaded Intel(R) PRO/1000 Network Driver - version 7.3.20-k2 Copyright (c) 1999-2006 Intel Corporation. ACPI: PCI Interrupt 0000:04:02.0[A] -> GSI 18 (level, low) -> IRQ 18 e1000: 0000:04:02.0: e1000_probe: (PCI:33MHz:32-bit) 00:15:17:26:b1:c7 e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection e1000e: Intel(R) PRO/1000 Network Driver - 0.2.0 e1000e: Copyright (c) 1999-2007 Intel Corporation. ACPI: PCI Interrupt 0000:00:19.0[A] -> GSI 20 (level, low) -> IRQ 20 PCI: Setting latency timer of device 0000:00:19.0 to 64 eth1: (PCI Express:2.5GB/s:Width x1) 00:15:17:26:b1:c9 eth1: Intel(R) PRO/1000 Network Connection eth1: MAC: 5, PHY: 6, PBA No: 0070ff-0ff sk98lin: driver has been replaced by the skge driver and is scheduled for removal PPP generic driver version 2.4.2 PPP Deflate Compression module registered PPP BSD Compression module registered tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> Uniform Multi-Platform E-IDE driver ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx Adaptec aacraid driver 1.1-5[2455]-ms st: Version 20080221, fixed bufsize 32768, s/g segs 256 Driver 'st' needs updating - please use bus_type methods Driver 'sd' needs updating - please use bus_type methods SCSI Media Changer driver v0.25 Driver 'ch' needs updating - please use bus_type methods ata_piix 0000:00:1f.2: version 2.12 ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 21 (level, low) -> IRQ 21 ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ] PCI: Setting latency timer of device 0000:00:1f.2 to 64 scsi0 : ata_piix scsi1 : ata_piix ata1: SATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0x3430 irq 14 ata2: SATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x3438 irq 15 ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1.00: ATA-8: WDC WD3200AAKS-75VYA0, 12.01B02, max UDMA/133 ata1.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 0/32) ata1.00: configured for UDMA/133 ata2: SATA link down (SStatus 0 SControl 300) scsi 0:0:0:0: Direct-Access ATA WDC WD3200AAKS-7 12.0 PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 sda4 sd 0:0:0:0: [sda] Attached SCSI disk sd 0:0:0:0: Attached scsi generic sg0 type 0 ACPI: PCI Interrupt 0000:00:1f.5[A] -> GSI 21 (level, low) -> IRQ 21 ata_piix 0000:00:1f.5: MAP [ P0 -- P1 -- ] PCI: Setting latency timer of device 0000:00:1f.5 to 64 scsi2 : ata_piix scsi3 : ata_piix ata3: SATA max UDMA/133 cmd 0x3448 ctl 0x3464 bmdma 0x3410 irq 21 ata4: SATA max UDMA/133 cmd 0x3440 ctl 0x3460 bmdma 0x3418 irq 21 ata3: SATA link down (SStatus 0 SControl 300) ata4: SATA link down (SStatus 0 SControl 300) sata_promise 0000:04:01.0: version 2.12 ACPI: PCI Interrupt 0000:04:01.0[A] -> GSI 17 (level, low) -> IRQ 17 scsi4 : sata_promise scsi5 : sata_promise scsi6 : sata_promise scsi7 : sata_promise ata5: SATA max UDMA/133 mmio m4096@0xe1960000 port 0xe1960200 irq 17 ata6: SATA max UDMA/133 mmio m4096@0xe1960000 port 0xe1960280 irq 17 ata7: SATA max UDMA/133 mmio m4096@0xe1960000 port 0xe1960300 irq 17 ata8: SATA max UDMA/133 mmio m4096@0xe1960000 port 0xe1960380 irq 17 ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata5.00: ATA-7: WDC WD4000YR-01PLB0, 01.06A01, max UDMA/133 ata5.00: 781422768 sectors, multi 0: LBA48 NCQ (depth 0/32) ata5.00: configured for UDMA/133 ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata6.00: ATA-7: WDC WD4000YR-01PLB0, 01.06A01, max UDMA/133 ata6.00: 781422768 sectors, multi 0: LBA48 NCQ (depth 0/32) ata6.00: configured for UDMA/133 ata7: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata7.00: ATA-7: WDC WD4000YR-01PLB0, 01.06A01, max UDMA/133 ata7.00: 781422768 sectors, multi 0: LBA48 NCQ (depth 0/32) ata7.00: configured for UDMA/133 ata8: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata8.00: ATA-7: WDC WD4000YR-01PLB0, 01.06A01, max UDMA/133 ata8.00: 781422768 sectors, multi 0: LBA48 NCQ (depth 0/32) ata8.00: configured for UDMA/133 scsi 4:0:0:0: Direct-Access ATA WDC WD4000YR-01P 01.0 PQ: 0 ANSI: 5 sd 4:0:0:0: [sdb] 781422768 512-byte hardware sectors (400088 MB) sd 4:0:0:0: [sdb] Write Protect is off sd 4:0:0:0: [sdb] Mode Sense: 00 3a 00 00 sd 4:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 4:0:0:0: [sdb] 781422768 512-byte hardware sectors (400088 MB) sd 4:0:0:0: [sdb] Write Protect is off sd 4:0:0:0: [sdb] Mode Sense: 00 3a 00 00 sd 4:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdb: sdb1 sd 4:0:0:0: [sdb] Attached SCSI disk sd 4:0:0:0: Attached scsi generic sg1 type 0 scsi 5:0:0:0: Direct-Access ATA WDC WD4000YR-01P 01.0 PQ: 0 ANSI: 5 sd 5:0:0:0: [sdc] 781422768 512-byte hardware sectors (400088 MB) sd 5:0:0:0: [sdc] Write Protect is off sd 5:0:0:0: [sdc] Mode Sense: 00 3a 00 00 sd 5:0:0:0: [sdc] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA sd 5:0:0:0: [sdc] 781422768 512-byte hardware sectors (400088 MB) sd 5:0:0:0: [sdc] Write Protect is off sd 5:0:0:0: [sdc] Mode Sense: 00 3a 00 00 sd 5:0:0:0: [sdc] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA sdc: sdc1 sd 5:0:0:0: [sdc] Attached SCSI disk sd 5:0:0:0: Attached scsi generic sg2 type 0 scsi 6:0:0:0: Direct-Access ATA WDC WD4000YR-01P 01.0 PQ: 0 ANSI: 5 sd 6:0:0:0: [sdd] 781422768 512-byte hardware sectors (400088 MB) sd 6:0:0:0: [sdd] Write Protect is off sd 6:0:0:0: [sdd] Mode Sense: 00 3a 00 00 sd 6:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 6:0:0:0: [sdd] 781422768 512-byte hardware sectors (400088 MB) sd 6:0:0:0: [sdd] Write Protect is off sd 6:0:0:0: [sdd] Mode Sense: 00 3a 00 00 sd 6:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdd: sdd1 sd 6:0:0:0: [sdd] Attached SCSI disk sd 6:0:0:0: Attached scsi generic sg3 type 0 scsi 7:0:0:0: Direct-Access ATA WDC WD4000YR-01P 01.0 PQ: 0 ANSI: 5 sd 7:0:0:0: [sde] 781422768 512-byte hardware sectors (400088 MB) sd 7:0:0:0: [sde] Write Protect is off sd 7:0:0:0: [sde] Mode Sense: 00 3a 00 00 sd 7:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 7:0:0:0: [sde] 781422768 512-byte hardware sectors (400088 MB) sd 7:0:0:0: [sde] Write Protect is off sd 7:0:0:0: [sde] Mode Sense: 00 3a 00 00 sd 7:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sde: sde1 sd 7:0:0:0: [sde] Attached SCSI disk sd 7:0:0:0: Attached scsi generic sg4 type 0 Fusion MPT base driver 3.04.06 Copyright (c) 1999-2007 LSI Corporation Fusion MPT SPI Host driver 3.04.06 ACPI: PCI Interrupt 0000:02:08.0[A] -> GSI 16 (level, low) -> IRQ 16 mptbase: ioc0: Initiating bringup ioc0: LSI53C1020A A1: Capabilities={Initiator,Target} scsi8 : ioc0: LSI53C1020A A1, FwRev=01032700h, Ports=1, MaxQ=255, IRQ=16 scsi 8:0:0:0: Sequential-Access HP Ultrium 3-SCSI D22D PQ: 0 ANSI: 3 target8:0:0: Beginning Domain Validation target8:0:0: Ending Domain Validation target8:0:0: FAST-160 WIDE SCSI 320.0 MB/s DT IU RTI PCOMP (6.25 ns, offset 64) st 8:0:0:0: Attached scsi tape st0 st 8:0:0:0: st0: try direct i/o: yes (alignment 4 B) st 8:0:0:0: Attached scsi generic sg5 type 1 Fusion MPT misc device (ioctl) driver 3.04.06 mptctl: Registered with Fusion MPT base driver mptctl: /dev/mptctl @ (major,minor=10,220) ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 17 (level, low) -> IRQ 17 PCI: Setting latency timer of device 0000:00:1a.7 to 64 ehci_hcd 0000:00:1a.7: EHCI Host Controller ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:1a.7: debug port 1 PCI: cache line size of 32 is not supported by device 0000:00:1a.7 ehci_hcd 0000:00:1a.7: irq 17, io mem 0xe1c21400 ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 6 ports detected ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23 PCI: Setting latency timer of device 0000:00:1d.7 to 64 ehci_hcd 0000:00:1d.7: EHCI Host Controller ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2 ehci_hcd 0000:00:1d.7: debug port 1 PCI: cache line size of 32 is not supported by device 0000:00:1d.7 ehci_hcd 0000:00:1d.7: irq 23, io mem 0xe1c21000 ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 6 ports detected USB Universal Host Controller Interface driver v3.0 ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 18 (level, low) -> IRQ 18 PCI: Setting latency timer of device 0000:00:1a.0 to 64 uhci_hcd 0000:00:1a.0: UHCI Host Controller uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:1a.0: irq 18, io base 0x000030c0 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1a.1[B] -> GSI 21 (level, low) -> IRQ 21 PCI: Setting latency timer of device 0000:00:1a.1 to 64 uhci_hcd 0000:00:1a.1: UHCI Host Controller uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:1a.1: irq 21, io base 0x000030a0 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1a.2[C] -> GSI 17 (level, low) -> IRQ 17 PCI: Setting latency timer of device 0000:00:1a.2 to 64 uhci_hcd 0000:00:1a.2: UHCI Host Controller uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5 uhci_hcd 0000:00:1a.2: irq 17, io base 0x00003080 usb usb5: configuration #1 chosen from 1 choice hub 5-0:1.0: USB hub found hub 5-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 23 PCI: Setting latency timer of device 0000:00:1d.0 to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6 uhci_hcd 0000:00:1d.0: irq 23, io base 0x00003060 usb usb6: configuration #1 chosen from 1 choice hub 6-0:1.0: USB hub found hub 6-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19 PCI: Setting latency timer of device 0000:00:1d.1 to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7 uhci_hcd 0000:00:1d.1: irq 19, io base 0x00003040 usb usb7: configuration #1 chosen from 1 choice hub 7-0:1.0: USB hub found hub 7-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18 PCI: Setting latency timer of device 0000:00:1d.2 to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8 uhci_hcd 0000:00:1d.2: irq 18, io base 0x00003020 usb usb8: configuration #1 chosen from 1 choice hub 8-0:1.0: USB hub found hub 8-0:1.0: 2 ports detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12 serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice input: AT Translated Set 2 keyboard as /class/input/input3 rtc_cmos: probe of 00:03 failed with error -16 input: ImExPS/2 Generic Explorer Mouse as /class/input/input4 md: raid1 personality registered for level 1 raid6: int32x1 825 MB/s raid6: int32x2 765 MB/s raid6: int32x4 656 MB/s raid6: int32x8 571 MB/s raid6: mmxx1 2593 MB/s raid6: mmxx2 2721 MB/s raid6: sse1x1 1743 MB/s raid6: sse1x2 2129 MB/s raid6: sse2x1 3223 MB/s raid6: sse2x2 3510 MB/s raid6: using algorithm sse2x2 (3510 MB/s) md: raid6 personality registered for level 6 md: raid5 personality registered for level 5 md: raid4 personality registered for level 4 device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@redhat.com EISA: Probing bus 0 at eisa.0 usbcore: registered new interface driver hiddev usbcore: registered new interface driver usbhid drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver GACT probability on Mirror/redirect action on u32 classifier Actions configured IPv4 over IPv4 tunneling driver ip_tables: (C) 2000-2006 Netfilter Core Team TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 NET: Registered protocol family 15 Bridge firewalling registered Ebtables v2.0 registered 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> Starting balanced_irq Using IPI Shortcut mode drivers/rtc/hctosys.c: unable to open rtc device (rtc0) md: Autodetecting RAID arrays. md: Scanned 4 and added 4 devices. md: autorun ... md: considering sde1 ... md: adding sde1 ... md: adding sdd1 ... md: adding sdc1 ... md: adding sdb1 ... md: created md5 md: bind<sdb1> md: bind<sdc1> md: bind<sdd1> md: bind<sde1> md: running: <sde1><sdd1><sdc1><sdb1> md: md5: raid array is not clean -- starting background reconstruction raid5: device sde1 operational as raid disk 3 raid5: device sdd1 operational as raid disk 2 raid5: device sdc1 operational as raid disk 1 raid5: device sdb1 operational as raid disk 0 raid5: allocated 4204kB for md5 raid5: raid level 5 set md5 active with 4 out of 4 devices, algorithm 2 RAID5 conf printout: --- rd:4 wd:4 disk 0, o:1, dev:sdb1 disk 1, o:1, dev:sdc1 disk 2, o:1, dev:sdd1 disk 3, o:1, dev:sde1 md: ... autorun DONE. md: resync of RAID array md5 md: minimum _guaranteed_ speed: 1000 KB/sec/disk. md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for resync. md: using 128k window, over a total of 390708736 blocks. md: resuming resync of md5 from checkpoint. EXT3-fs: INFO: recovery required on readonly filesystem. EXT3-fs: write access will be enabled during recovery. kjournald starting. Commit interval 5 seconds EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 352k freed Adding 1951888k swap on /dev/sda4. Priority:-1 extents:1 across:1951888k EXT3 FS on sda3, internal journal kjournald starting. Commit interval 5 seconds EXT3 FS on sda1, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on dm-0, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on dm-1, internal journal EXT3-fs: mounted filesystem with ordered data mode. e1000: eth0: e1000_watchdog: NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX warning: `ntpd' uses 32-bit capabilities (legacy support in use)
| |