Messages in this thread | | | From | Andrey Borzenkov <> | Subject | 2.6.17: dmesg flooded with "ohci_hcd 0000:00:02.0: wakeup" | Date | Sun, 18 Jun 2006 19:19:50 +0400 |
| |
-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1
After reboot with 2.6.17 dmesg is overflowed with the above. 2.6.16.20 was OK. Please let me know what additional information may be useful; for now I simply commented out this printk. dmesg, lsusb and lspci follow.
00:00.0 0600: 10b9:1644 (rev 01) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR+ Latency: 0 Region 0: Memory at f0000000 (32-bit, prefetchable) [size=64M] Capabilities: [b0] AGP version 2.0 Status: RQ=28 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4 Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none> Capabilities: [a4] Power Management version 1 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:01.0 0604: 10b9:5247 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 Memory behind bridge: f7f00000-fdffffff Prefetchable memory behind bridge: 3c000000-3c0fffff Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR+ BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
00:02.0 0c03: 10b9:5237 (rev 03) (prog-if 10) Subsystem: 1179:0004 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (20000ns max), Cache Line Size 08 Interrupt: pin A routed to IRQ 11 Region 0: Memory at f7eff000 (32-bit, non-prefetchable) [size=4K] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:04.0 0101: 10b9:5229 (rev c3) (prog-if f0) Subsystem: 1179:0004 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (500ns min, 1000ns max) Interrupt: pin A routed to IRQ 255 Region 4: I/O ports at eff0 [size=16] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:06.0 0401: 10b9:5451 (rev 01) Subsystem: 1179:0001 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR+ <PERR+ Latency: 64 (500ns min, 6000ns max) Interrupt: pin A routed to IRQ 11 Region 0: I/O ports at ed00 [size=256] Region 1: Memory at f7efe000 (32-bit, non-prefetchable) [size=4K] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.0 0601: 10b9:1533 Subsystem: 1179:0004 Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Capabilities: [a0] Power Management version 1 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:08.0 0680: 10b9:7101 Subsystem: 1179:0001 Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:0a.0 0200: 8086:1229 (rev 08) Subsystem: 1179:0003 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (2000ns min, 14000ns max), Cache Line Size 08 Interrupt: pin A routed to IRQ 11 Region 0: Memory at f7efd000 (32-bit, non-prefetchable) [size=4K] Region 1: I/O ports at eb40 [size=64] Region 2: Memory at f7d00000 (32-bit, non-prefetchable) [size=1M] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=2 PME-
00:10.0 0607: 104c:ac50 (rev 01) Subsystem: 12a3:ab01 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 168, Cache Line Size 08 Interrupt: pin A routed to IRQ 11 Region 0: Memory at 3c100000 (32-bit, non-prefetchable) [size=4K] Bus: primary=00, secondary=02, subordinate=05, sec-latency=176 Memory window 0: 30000000-31fff000 (prefetchable) Memory window 1: 32000000-33fff000 I/O window 0: 00001000-000010ff I/O window 1: 00001400-000014ff BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt- PostWrite+ 16-bit legacy interface ports at 0001
00:11.0 0607: 1179:0617 (rev 32) Subsystem: 1179:0001 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 168 Interrupt: pin A routed to IRQ 11 Region 0: Memory at 3c101000 (32-bit, non-prefetchable) [size=4K] Bus: primary=00, secondary=06, subordinate=09, sec-latency=0 Memory window 0: 34000000-35fff000 (prefetchable) Memory window 1: 36000000-37fff000 I/O window 0: 00001800-000018ff I/O window 1: 00001c00-00001cff BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+ 16-bit legacy interface ports at 0001
00:11.1 0607: 1179:0617 (rev 32) Subsystem: 1179:0001 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 168 Interrupt: pin B routed to IRQ 11 Region 0: Memory at 3c102000 (32-bit, non-prefetchable) [size=4K] Bus: primary=00, secondary=0a, subordinate=0d, sec-latency=0 Memory window 0: 38000000-39fff000 (prefetchable) Memory window 1: 3a000000-3bfff000 I/O window 0: 00002000-000020ff I/O window 1: 00002400-000024ff BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+ 16-bit legacy interface ports at 0001
00:12.0 0880: 1179:0805 (rev 03) Subsystem: 1179:0001 Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin A routed to IRQ 11 Region 0: Memory at f7cffe00 (32-bit, non-prefetchable) [size=512] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.0 0300: 1023:8820 (rev 82) Subsystem: 1179:0001 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 8 Interrupt: pin A routed to IRQ 11 Region 0: Memory at fc000000 (32-bit, non-prefetchable) [size=32M] Region 1: Memory at fbc00000 (32-bit, non-prefetchable) [size=4M] Region 2: Memory at f8000000 (32-bit, non-prefetchable) [size=32M] Region 3: Memory at f7ff8000 (32-bit, non-prefetchable) [size=32K] [virtual] Expansion ROM at 3c000000 [disabled] [size=64K] Capabilities: [80] AGP version 2.0 Status: RQ=33 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4 Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none> Capabilities: [90] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
{pts/0}% lsusb -vv
Bus 001 Device 001: ID 0000:0000 Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 1.10 bDeviceClass 9 Hub bDeviceSubClass 0 Unused bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x0000 idProduct 0x0000 bcdDevice 2.06 iManufacturer 3 Linux 2.6.17-1avb ohci_hcd iProduct 2 OHCI Host Controller iSerial 1 0000:00:02.0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 25 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xe0 Self Powered Remote Wakeup MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 9 Hub bInterfaceSubClass 0 Unused bInterfaceProtocol 0 iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0002 1x 2 bytes bInterval 255 Hub Descriptor: bLength 9 bDescriptorType 41 nNbrPorts 3 wHubCharacteristic 0x0002 No power switching (usb 1.0) Ganged overcurrent protection bPwrOn2PwrGood 1 * 2 milli seconds bHubContrCurrent 0 milli Ampere DeviceRemovable 0x00 PortPwrCtrlMask 0xff Hub Port Status: Port 1: 0000.0100 power Port 2: 0000.0100 power Port 3: 0000.0100 power Device Status: 0x0003 Self Powered Remote Wakeup Enabled
dmesg: Linux version 2.6.17-1avb (bor@cooker) (gcc version 4.1.1 20060518 (prerelease)) #2 Sun Jun 18 15:54:15 MSD 2006 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e0000 - 00000000000eee00 (reserved) BIOS-e820: 00000000000eee00 - 00000000000ef000 (ACPI NVS) BIOS-e820: 00000000000ef000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000001ef60000 (usable) BIOS-e820: 000000001ef60000 - 000000001ef70000 (ACPI data) BIOS-e820: 000000001ef70000 - 0000000020000000 (reserved) BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) 495MB LOWMEM available. On node 0 totalpages: 126816 DMA zone: 4096 pages, LIFO batch:0 Normal zone: 122720 pages, LIFO batch:31 DMI 2.3 present. ACPI: RSDP (v000 TOSHIB ) @ 0x000f0090 ACPI: RSDT (v001 TOSHIB 750 0x00970814 TASM 0x04010000) @ 0x1ef60000 ACPI: FADT (v002 TOSHIB 750 0x00970814 TASM 0x04010000) @ 0x1ef60054 ACPI: DSDT (v001 TOSHIB 4000 0x20020417 MSFT 0x0100000a) @ 0x00000000 ACPI: PM-Timer IO Port: 0xee08 Allocating PCI resources starting at 30000000 (gap: 20000000:dff80000) Built 1 zonelists Kernel command line: root=/dev/hda2 pinit hdc=ide-cd resume=/dev/hda1 splash=silent elevator=cfq vga=791 3 Local APIC disabled by BIOS -- you can enable it with "lapic" mapped APIC to ffffd000 (013e4000) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 2048 (order: 11, 8192 bytes) Detected 747.740 MHz processor. Using pmtmr for high-res timesource Console: colour dummy device 80x25 Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 499180k/507264k available (1663k kernel code, 7456k reserved, 795k data, 176k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 1496.77 BogoMIPS (lpj=748388) Mount-cache hash table entries: 512 CPU: After generic identify, caps: 0387f9ff 00000000 00000000 00000000 00000000 00000000 00000000 CPU: After vendor identify, caps: 0387f9ff 00000000 00000000 00000000 00000000 00000000 00000000 CPU: L1 I cache: 16K, L1 D cache: 16K CPU: L2 cache: 256K CPU serial number disabled. CPU: After all inits, caps: 0383f9ff 00000000 00000000 00000040 00000000 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU: Intel Pentium III (Coppermine) stepping 0a Checking 'hlt' instruction... OK. SMP alternatives: switching to UP code Freeing SMP alternatives: 0k freed ACPI: setting ELCR to 0200 (from 0a00) checking if image is initramfs... it is Freeing initrd memory: 230k freed NET: Registered protocol family 16 ACPI: bus type pci registered PCI: PCI BIOS revision 2.10 entry at 0xfe5ae, last bus=5 Setting up standard PCI resources ACPI: Subsystem revision 20060127 ACPI: Interpreter enabled ACPI: Using PIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) ACPI: Assume root bridge [\_SB_.PCI0] bus is 0 PCI quirk: region ee00-ee3f claimed by ali7101 ACPI PCI quirk: region ef00-ef1f claimed by ali7101 SMB Boot video device is 0000:01:00.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 *11) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 *11) ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 *11) ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 *11) ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT] ACPI: Power Resource [PFAN] (off) Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 12 devices PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report TC classifier action (bugs to netdev@vger.kernel.org cc hadi@cyberus.ca) PCI: Bridge: 0000:00:01.0 IO window: disabled. MEM window: f7f00000-fdffffff PREFETCH window: 3c000000-3c0fffff PCI: Bus 2, cardbus bridge: 0000:00:10.0 IO window: 00001000-000010ff IO window: 00001400-000014ff PREFETCH window: 30000000-31ffffff MEM window: 32000000-33ffffff PCI: Bus 6, cardbus bridge: 0000:00:11.0 IO window: 00001800-000018ff IO window: 00001c00-00001cff PREFETCH window: 34000000-35ffffff MEM window: 36000000-37ffffff PCI: Bus 10, cardbus bridge: 0000:00:11.1 IO window: 00002000-000020ff IO window: 00002400-000024ff PREFETCH window: 38000000-39ffffff MEM window: 3a000000-3bffffff PCI: Setting latency timer of device 0000:00:01.0 to 64 PCI: Enabling device 0000:00:10.0 (0000 -> 0003) ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11 PCI: setting IRQ 11 as level-triggered ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11 PCI: Enabling device 0000:00:11.0 (0000 -> 0003) ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11 ACPI: PCI Interrupt 0000:00:11.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 PCI: Enabling device 0000:00:11.1 (0000 -> 0003) ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11 ACPI: PCI Interrupt 0000:00:11.1[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11 NET: Registered protocol family 2 IP route cache hash table entries: 4096 (order: 2, 16384 bytes) TCP established hash table entries: 16384 (order: 6, 262144 bytes) TCP bind hash table entries: 8192 (order: 5, 163840 bytes) TCP: Hash tables configured (established 16384 bind 8192) TCP reno registered audit: initializing netlink socket (disabled) audit(1150642545.524:1): initialized VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) Activating ISA DMA hang workarounds. vesafb: framebuffer at 0xfc000000, mapped to 0xdf880000, using 3072k, total 16384k vesafb: mode is 1024x768x16, linelength=2048, pages=9 vesafb: protected mode interface info at c000:775e vesafb: scrolling: redraw vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 Console: switching to colour frame buffer device 128x48 fb0: VESA VGA frame buffer device Real Time Clock Driver v1.12ac RAMDISK driver initialized: 16 RAM disks of 32000K size 1024 blocksize PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 mice: PS/2 mouse device common for all mice NET: Registered protocol family 1 Using IPI Shortcut mode ACPI wakeup devices: COM USB1 ASND VIY0 VIY1 LAN MPC0 MPC1 NOV0 LID ACPI: (supports S0 S3 S4 S5) BIOS EDD facility v0.16 2004-Jun-25, 1 devices found Freeing unused kernel memory: 176k freed Write protecting the kernel read-only data: 516k Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx input: AT Translated Set 2 keyboard as /class/input/input0 ALI15X3: IDE controller at PCI slot 0000:00:04.0 ACPI: PCI Interrupt 0000:00:04.0[A]: no GSI ALI15X3: chipset revision 195 ALI15X3: not 100% native mode: will probe irqs later ide0: BM-DMA at 0xeff0-0xeff7, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0xeff8-0xefff, BIOS settings: hdc:DMA, hdd:pio Probing IDE interface ide0... hda: IC25N020ATDA04-0, ATA DISK drive input: ImPS/2 Generic Wheel Mouse as /class/input/input1 ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... hdc: TOSHIBA DVD-ROM SD-C2502, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 hda: max request size: 128KiB hda: 39070080 sectors (20003 MB) w/1806KiB Cache, CHS=38760/16/63, UDMA(33) hda: cache flushes not supported hda: hda1 hda2 ReiserFS: hda2: found reiserfs format "3.6" with standard journal ReiserFS: hda2: using ordered data mode ReiserFS: hda2: journal params: device hda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: hda2: checking transaction log (hda2) ReiserFS: hda2: Using r5 hash to sort names usbcore: registered new driver usbfs usbcore: registered new driver hub ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 11 ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LNKG] -> GSI 11 (level, low) -> IRQ 11 ohci_hcd 0000:00:02.0: OHCI Host Controller ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1 ohci_hcd 0000:00:02.0: irq 11, io mem 0xf7eff000 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 3 ports detected ohci_hcd 0000:00:02.0: wakeup ohci_hcd 0000:00:02.0: wakeup ohci_hcd 0000:00:02.0: wakeup ohci_hcd 0000:00:02.0: wakeup ohci_hcd 0000:00:02.0: wakeup ohci_hcd 0000:00:02.0: wakeup Linux agpgart interface v0.101 (c) Dave Jones agpgart: Detected ALi M1644 chipset agpgart: AGP aperture is 64M @ 0xf0000000 ohci_hcd 0000:00:02.0: wakeup ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11 Yenta: CardBus bridge found at 0000:00:10.0 [12a3:ab01] Yenta: Using CSCINT to route CSC interrupts to PCI Yenta: Routing CardBus interrupts to PCI Yenta TI: socket 0000:00:10.0, mfunc 0x01000002, devctl 0x60 Yenta: ISA IRQ mask 0x0000, PCI irq 11 Socket status: 30000059 ACPI: PCI Interrupt 0000:00:11.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 Yenta: CardBus bridge found at 0000:00:11.0 [1179:0001] ohci_hcd 0000:00:02.0: wakeup Yenta: ISA IRQ mask 0x04b8, PCI irq 11 Socket status: 30000007 ohci_hcd 0000:00:02.0: wakeup pccard: PCMCIA card inserted into slot 0 ohci_hcd 0000:00:02.0: wakeup cs: memory probe 0x0c0000-0x0fffff: excluding 0xc0000-0xcbfff 0xe0000-0xfffff cs: memory probe 0x60000000-0x60ffffff: clean. cs: memory probe 0xa0000000-0xa0ffffff: clean. pcmcia: registering new device pcmcia0.0 ACPI: PCI Interrupt 0000:00:11.1[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11 Yenta: CardBus bridge found at 0000:00:11.1 [1179:0001] wlags49_h1_cs v7.18 for PCMCIA, 03/31/2004 14:31:00 by Agere Systems, http://www.agere.com *** Modified for kernel 2.6 by Andrey Borzenkov <arvidjaar@mail.ru> $Revision: 22 $ *** Station Mode (STA) Support: YES *** Access Point Mode (AP) Support: YES ohci_hcd 0000:00:02.0: wakeup eth0: PRI 31 variant 2 version 9.48 eth0: NIC 5 variant 2 version 1.02 eth0: Wireless, io_addr 0x100, irq 11, mac_address 00:02:2D:26:95:6C Yenta: ISA IRQ mask 0x04b8, PCI irq 11 Socket status: 30000007 ohci_hcd 0000:00:02.0: wakeup ohci_hcd 0000:00:02.0: wakeup ACPI: AC Adapter [ADP1] (on-line) ACPI: Battery Slot [BAT1] (battery present) ACPI: Battery Slot [BAT2] (battery absent) ACPI: Power Button (FF) [PWRF] ACPI: Lid Switch [LID] ACPI: Fan [FAN] (off) ACPI: CPU0 (power states: C1[C1] C2[C2]) ohci_hcd 0000:00:02.0: wakeup ACPI: Thermal Zone [THRM] (53 C) toshiba_acpi: Toshiba Laptop ACPI Extras version 0.18 toshiba_acpi: HCI method: \_SB_.VALD.GHCI ACPI: Video Device [VGA] (multi-head: yes rom: yes post: no) ohci_hcd 0000:00:02.0: wakeup ohci_hcd 0000:00:02.0: wakeup ohci_hcd 0000:00:02.0: wakeup Adding 500432k swap on /dev/hda1. Priority:-1 extents:1 across:500432k ohci_hcd 0000:00:02.0: wakeup ohci_hcd 0000:00:02.0: wakeup ohci_hcd 0000:00:02.0: wakeup loop: loaded (max 8 devices) ohci_hcd 0000:00:02.0: wakeup ohci_hcd 0000:00:02.0: wakeup ohci_hcd 0000:00:02.0: wakeup ohci_hcd 0000:00:02.0: wakeup ohci_hcd 0000:00:02.0: wakeup ohci_hcd 0000:00:02.0: wakeup ohci_hcd 0000:00:02.0: wakeup hdc: ATAPI 24X DVD-ROM drive, 128kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 ohci_hcd 0000:00:02.0: wakeup ohci_hcd 0000:00:02.0: wakeup -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.4.2.2 (GNU/Linux)
iD8DBQFElW8WR6LMutpd94wRApdPAJ45BIDoOzPab3YncJ1MXO0RWyHZeQCfSyli LqZY+QERkJQBKtw/Qr/w5Xg= =nQS6 -----END PGP SIGNATURE----- - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
| |