Messages in this thread | | | Date | Wed, 29 Mar 2006 15:06:18 -0500 (EST) | From | "Jeremy Johnson" <> | Subject | pcmciautils Kyocera KPC650 |
| |
Hi,
I'm trying to get a Kyocera KPC650 pcmcia airmodem card working. I have an HP SE2000L amd64 Turino laptop running amd64 Gentoo with kernel-2.6.15-r1 and pcmciautils-013 and for good measure pcmcia-cs-cis-3.2.8-r1. I also have coldplug-20040920 and hotplug-20040923-r1 and hotplug-base-20040401
# cat /etc/modules.autoload.d/kernel-2.6 ndiswrapper fglrx ohci_hcd ehci_hcd #usbserial vendor=0x0c88 product=0x17da maxSize=2048 usbserial vendor=0x0c88 product=0x17da ppp_async
# grep YENTA .config CONFIG_YENTA=y
# grep PCMCIA .config|grep -v "#" CONFIG_PCMCIA_DEBUG=y CONFIG_PCMCIA=y CONFIG_PCMCIA_LOAD_CIS=y CONFIG_PCMCIA_IOCTL=y CONFIG_PCMCIA_FDOMAIN=m CONFIG_PCMCIA_QLOGIC=m CONFIG_PCMCIA_SYM53C500=m CONFIG_NET_PCMCIA=y
# grep USB_SERIAL .config|grep -v "#" CONFIG_USB_SERIAL=m CONFIG_USB_SERIAL_GENERIC=y
I have activated this card in WindowsXP and connected properly to Verizon's EVDO VZAccess network. But I can't get the card to be recognized under linux (The blue led light does not light up)
# pccardctl status Socket 0: 3.3V 32-bit PC Card # pccardctl info PRODID_1="" PRODID_2="" PRODID_3="" PRODID_4="" MANFID=0000,0000 FUNCID=255
When I eject the card I get the following error message: PCMCIA: socket ffff810017ac6048: *** DANGER *** unable to remove socket power
So I followed the suggestions in the mini-howto <http:www.kernel.org/pub/linux/utils/kernel/pcmcia/howto.html> and the suggestions at ~/pcmcia.html#mailinglist
# lspci -v|grep subordinate Bus: primary=00, secondary=01, subordinate=01, sec-latency=64 Bus: primary=00, secondary=05, subordinate=05, sec-latency=64 Bus: primary=05, secondary=06, subordinate=09, sec-latency=176 which looks OK since my yenta_socket is 0000:05:09.0
I also tried the ~/powerbugs.html#2 suggestions and added reserve=0xc020a000,0x5000 to my kernel cmd line.
# lspci -vv 05:09.0 CardBus bridge: Texas Instruments PCIxx21/x515 Cardbus Controller Subsystem: Hewlett-Packard Company Unknown device 3091 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 168, Cache Line Size 10 Interrupt: pin A routed to IRQ 185 Region 0: Memory at c020a000 (32-bit, non-prefetchable) [size=4K] Bus: primary=05, secondary=06, subordinate=09, sec-latency=176 Memory window 0: 30000000-31fff000 (prefetchable) Memory window 1: 32000000-33fff000 I/O window 0: 0000a400-0000a4ff I/O window 1: 0000a800-0000a8ff BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+ 16-bit legacy interface ports at 0001
/proc/iomem reports: c0209000-c02090ff : 0000:05:09.4 c0209400-c02094ff : 0000:05:09.4 c020a000-c020afff : 0000:05:09.0 c020a000-c020afff : yenta_socket
At this point I don't know how to proceed next. Everything I've tried has failed. But I know others have gotten this card to work on other linux laptops.
So is this a bug or something that I've neglected to do? THANKS.
-- Anita C. Johnson c/o Jeremy P.O. Box 877 23405 Front St. Accomac, VA 23301 Work: (757)787-8743 Fax: (757)787-3570Module Size Used by ip_conntrack_irc 8144 0 ip_conntrack_ftp 8848 0 ipt_REJECT 6464 4 ipt_LOG 8000 4 ipt_limit 4288 4 ipt_state 3904 181 ip_conntrack 50236 3 ip_conntrack_irc,ip_conntrack_ftp,ipt_state iptable_filter 4800 1 ip_tables 20224 5 ipt_REJECT,ipt_LOG,ipt_limit,ipt_state,iptable_filter rfcomm 35296 6 l2cap 24064 5 rfcomm snd_pcm_oss 48352 0 snd_mixer_oss 16768 1 snd_pcm_oss snd_seq_dummy 5124 0 snd_seq_oss 31616 0 snd_seq_midi_event 8704 1 snd_seq_oss snd_seq 51456 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi_event snd_seq_device 9360 3 snd_seq_dummy,snd_seq_oss,snd_seq uhci_hcd 31832 0 ohci1394 31116 0 8139cp 19968 0 snd_atiixp_modem 15116 1 snd_atiixp 18772 1 snd_ac97_codec 99416 2 snd_atiixp_modem,snd_atiixp snd_ac97_bus 4480 1 snd_ac97_codec snd_pcm 82440 4 snd_pcm_oss,snd_atiixp_modem,snd_atiixp,snd_ac97_codec snd_timer 22472 2 snd_seq,snd_pcm snd 50504 14 snd_pcm_oss,snd_mixer_oss,snd_seq_oss,snd_seq,snd_seq_device,snd_atiixp_modem,snd_atiixp,snd_ac97_codec,snd_pcm,snd_timer snd_page_alloc 11152 3 snd_atiixp_modem,snd_atiixp,snd_pcm binfmt_misc 11724 1 hci_usb 16404 5 ppp_async 11200 0 ppp_generic 26912 1 ppp_async slhc 8000 1 ppp_generic crc_ccitt 4096 1 ppp_async usbserial 29232 0 ehci_hcd 40712 0 ohci_hcd 30788 0 fglrx 501696 36 ndiswrapper 194976 0 acj description: Notebook product: HP Pavilion (EC436AV#ABA) vendor: Hewlett-Packard version: Rev 1 serial: CNF6030DRG width: 32 bits capabilities: smbios-2.31 dmi-2.31 configuration: boot=oem-specific chassis=notebook uuid=60BB13B2-9787-DA11-8723-00163613CDAF *-core description: Motherboard product: 3093 vendor: Quanta physical id: 0 version: 47.0F serial: None *-firmware description: BIOS vendor: Hewlett-Packard physical id: 0 version: F.21 (12/09/2005) size: 105KB capacity: 448KB capabilities: pci pcmcia pnp apm upgrade shadowing escd cdboot int5printscreen int9keyboard int14serial int17printer int10video acpi usb *-cpu description: CPU product: AMD Turion(tm) 64 Mobile Technology ML-37 vendor: Advanced Micro Devices [AMD] physical id: 4 bus info: cpu@0 version: AMD Turion(tm) 64 Mobile ML slot: U23 size: 2GHz capacity: 2GHz width: 64 bits clock: 200MHz capabilities: fpu fpu_exception wp vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush mmx fxsr sse sse2 syscall nx mmxext fxsr_opt x86-64 3dnowext 3dnow pni lahf_lm cpufreq *-cache description: L2 cache physical id: 5 slot: L2 Cache size: 1MB capacity: 1MB capabilities: synchronous internal write-back *-memory description: System Memory physical id: 9 slot: System board or motherboard size: 512MB *-bank:0 description: DIMM DRAM Synchronous physical id: 0 slot: U5 size: 256MB width: 32 bits *-bank:1 description: DIMM DRAM Synchronous physical id: 1 slot: U6 size: 256MB width: 32 bits *-pci:0 description: Host bridge product: RS480 Host Bridge vendor: ATI Technologies Inc physical id: 100 bus info: pci@00:00.0 version: 10 width: 32 bits clock: 66MHz *-pci:0 description: PCI bridge product: ATI Technologies Inc vendor: ATI Technologies Inc physical id: 1 bus info: pci@00:01.0 version: 00 width: 32 bits clock: 66MHz capabilities: pci normal_decode bus_master cap_list *-display description: VGA compatible controller product: ATI Radeon XPRESS 200M 5955 (PCIE) vendor: ATI Technologies Inc physical id: 5 bus info: pci@01:05.0 logical name: /dev/fb0 version: 00 size: 128MB width: 32 bits clock: 66MHz capabilities: vga bus_master cap_list fb configuration: depth=24 driver=fglrx_pci frequency=75.69Hz mode=1024x768 visual=truecolor xres=1024 yres=768 resources: iomemory:c8000000-cfffffff ioport:9000-90ff iomemory:c0100000-c010ffff irq:185 *-usb:0 description: USB Controller product: IXP SB400 USB Host Controller vendor: ATI Technologies Inc physical id: 13 bus info: pci@00:13.0 version: 80 width: 32 bits clock: 66MHz capabilities: ohci bus_master cap_list configuration: driver=ohci_hcd resources: iomemory:c0000000-c0000fff irq:217 *-usbhost product: OHCI Host Controller vendor: Linux 2.6.15-gentoo-r1 ohci_hcd physical id: 1 bus info: usb@2 logical name: usb2 version: 2.06 capabilities: usb-1.10 configuration: driver=hub maxpower=0mA slots=4 speed=12.0MB/s *-usb description: Mouse product: F8E842-DL Mouse vendor: Belkin physical id: 1 bus info: usb@2:1 version: 2.70 capabilities: usb-1.10 configuration: driver=usbhid maxpower=100mA speed=1.5MB/s *-usb:1 description: USB Controller product: IXP SB400 USB Host Controller vendor: ATI Technologies Inc physical id: 13.1 bus info: pci@00:13.1 version: 80 width: 32 bits clock: 66MHz capabilities: ohci bus_master cap_list configuration: driver=ohci_hcd resources: iomemory:c0001000-c0001fff irq:217 *-usbhost product: OHCI Host Controller vendor: Linux 2.6.15-gentoo-r1 ohci_hcd physical id: 1 bus info: usb@3 logical name: usb3 version: 2.06 capabilities: usb-1.10 configuration: driver=hub maxpower=0mA slots=4 speed=12.0MB/s *-usb description: Bluetooth wireless interface product: HP integrated Bluetooth module vendor: Broadcom physical id: 3 bus info: usb@3:3 version: 0.17 capabilities: bluetooth usb-1.10 configuration: driver=hci_usb maxpower=0mA speed=12.0MB/s *-usb:2 description: USB Controller product: IXP SB400 USB2 Host Controller vendor: ATI Technologies Inc physical id: 13.2 bus info: pci@00:13.2 version: 80 width: 32 bits clock: 66MHz capabilities: ehci bus_master cap_list configuration: driver=ehci_hcd resources: iomemory:c0002000-c0002fff irq:217 *-usbhost product: EHCI Host Controller vendor: Linux 2.6.15-gentoo-r1 ehci_hcd physical id: 1 bus info: usb@1 logical name: usb1 version: 2.06 capabilities: usb-2.00 configuration: driver=hub maxpower=0mA slots=8 speed=480.0MB/s *-serial UNCLAIMED description: SMBus product: IXP SB400 SMBus Controller vendor: ATI Technologies Inc physical id: 14 bus info: pci@00:14.0 version: 81 width: 32 bits clock: 66MHz capabilities: cap_list resources: ioport:8400-840f iomemory:c0003000-c00033ff *-ide description: IDE interface product: Standard Dual Channel PCI IDE Controller ATI vendor: ATI Technologies Inc physical id: 14.1 bus info: pci@00:14.1 version: 80 width: 32 bits clock: 66MHz capabilities: ide bus_master cap_list configuration: driver=ATIIXP_IDE resources: ioport:8410-841f irq:201 *-ide:0 description: IDE Channel 0 physical id: 0 bus info: ide@0 logical name: ide0 clock: 66MHz *-disk description: ATA Disk product: TOSHIBA MK1031GAS vendor: Toshiba physical id: 0 bus info: ide@0.0 logical name: /dev/hda version: AA204C serial: X5DM7021S size: 93GB capacity: 93GB capabilities: ata dma lba iordy smart security pm apm configuration: apm=off mode=udma5 smart=on *-ide:1 description: IDE Channel 1 physical id: 1 bus info: ide@1 logical name: ide1 clock: 66MHz *-cdrom description: DVD writer product: PIONEER DVDRW DVR-K15 vendor: Pioneer physical id: 0 bus info: ide@1.0 logical name: /dev/hdc version: 1.11 capabilities: packet atapi cdrom removable nonmagnetic dma lba iordy pm audio cd-r cd-rw dvd dvd-r *-isa UNCLAIMED description: ISA bridge product: IXP SB400 PCI-ISA Bridge vendor: ATI Technologies Inc physical id: 14.3 bus info: pci@00:14.3 version: 80 width: 32 bits clock: 66MHz capabilities: isa bus_master *-pci:1 description: PCI bridge product: IXP SB400 PCI-PCI Bridge vendor: ATI Technologies Inc physical id: 14.4 bus info: pci@00:14.4 version: 80 width: 32 bits clock: 66MHz capabilities: pci subtractive_decode bus_master *-network:0 description: Ethernet interface product: RTL-8139/8139C/8139C+ vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@05:00.0 logical name: eth0 version: 10 serial: 00:16:36:13:cd:af size: 100MB/s capacity: 100MB/s width: 32 bits clock: 33MHz capabilities: bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegociation configuration: autonegociation=on broadcast=yes driver=8139too driverversion=0.9.27 duplex=full ip=10.0.0.2 link=yes multicast=yes port=MII speed=100MB/s resources: ioport:a000-a0ff iomemory:c0208000-c02080ff irq:193 *-network:1 DISABLED description: Wireless interface product: BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller vendor: Broadcom Corporation physical id: 2 bus info: pci@05:02.0 logical name: wlan0 version: 02 serial: 00:14:a5:69:0e:b4 width: 32 bits clock: 33MHz capabilities: bus_master ethernet physical wireless configuration: broadcast=yes driver=ndiswrapper link=no multicast=yes wireless=IEEE 802.11g resources: iomemory:c0204000-c0205fff irq:209 *-pcmcia description: CardBus bridge product: PCIxx21/x515 Cardbus Controller vendor: Texas Instruments physical id: 9 bus info: pci@05:09.0 version: 00 width: 32 bits clock: 33MHz capabilities: pcmcia bus_master cap_list configuration: driver=yenta_cardbus resources: iomemory:c020a000-c020afff irq:185 *-firewire description: FireWire (IEEE 1394) product: OHCI Compliant IEEE 1394 Host Controller vendor: Texas Instruments physical id: 9.2 bus info: pci@05:09.2 version: 00 width: 32 bits clock: 33MHz capabilities: ohci bus_master cap_list configuration: driver=ohci1394 resources: iomemory:c0208800-c0208fff iomemory:c0200000-c0203fff irq:225 *-storage UNCLAIMED description: Mass storage controller product: PCIxx21 Integrated FlashMedia Controller vendor: Texas Instruments physical id: 9.3 bus info: pci@05:09.3 version: 00 width: 32 bits clock: 33MHz capabilities: storage bus_master cap_list resources: iomemory:c0206000-c0207fff irq:10 *-system UNCLAIMED description: Generic system peripheral product: PCI6411, PCI6421, PCI6611, PCI6621, PCI7411, PCI7421, PCI7611, PCI7621 Secure Digital (SD) Controller vendor: Texas Instruments physical id: 9.4 bus info: pci@05:09.4 version: 00 width: 32 bits clock: 33MHz capabilities: bus_master cap_list resources: iomemory:c0209400-c02094ff iomemory:c0209000-c02090ff iomemory:c0208400-c02084ff irq:10 *-multimedia description: Multimedia audio controller product: IXP SB400 AC'97 Audio Controller vendor: ATI Technologies Inc physical id: 14.5 bus info: pci@00:14.5 version: 80 width: 32 bits clock: 66MHz capabilities: bus_master cap_list configuration: driver=ATI IXP AC97 controller resources: iomemory:c0003400-c00034ff irq:185 *-communication description: Modem product: ATI SB400 - AC'97 Modem Controller vendor: ATI Technologies Inc physical id: 14.6 bus info: pci@00:14.6 version: 80 width: 32 bits clock: 66MHz capabilities: generic bus_master cap_list configuration: driver=ATI IXP MC97 controller resources: iomemory:c0003800-c00038ff irq:185 *-pci:1 description: Host bridge product: K8 [Athlon64/Opteron] HyperTransport Technology Configuration vendor: Advanced Micro Devices [AMD] physical id: 101 bus info: pci@00:18.0 version: 00 width: 32 bits clock: 33MHz *-pci:2 description: Host bridge product: K8 [Athlon64/Opteron] Address Map vendor: Advanced Micro Devices [AMD] physical id: 102 bus info: pci@00:18.1 version: 00 width: 32 bits clock: 33MHz *-pci:3 description: Host bridge product: K8 [Athlon64/Opteron] DRAM Controller vendor: Advanced Micro Devices [AMD] physical id: 103 bus info: pci@00:18.2 version: 00 width: 32 bits clock: 33MHz *-pci:4 description: Host bridge product: K8 [Athlon64/Opteron] Miscellaneous Control vendor: Advanced Micro Devices [AMD] physical id: 104 bus info: pci@00:18.3 version: 00 width: 32 bits clock: 33MHzBootdata ok (command line is root=/dev/hda5 reserve=0xc020a000,0x5000 vga=0x318 video=vesafb:ywrap,mtrr,1024x768-32@72 splash=silent,fadein,theme:livecd-2005.1,tty:12 quiet CONSOLE=/dev/tty1) Linux version 2.6.15-gentoo-r1 (root@acj) (gcc version 3.4.4 (Gentoo 3.4.4-r1, ssp-3.4.4-1.0, pie-8.7.8)) #19 SMP Wed Mar 29 10:50:39 EST 2006 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009f800 (usable) BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) BIOS-e820: 00000000000d2000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 0000000017ef0000 (usable) BIOS-e820: 0000000017ef0000 - 0000000017eff000 (ACPI data) BIOS-e820: 0000000017eff000 - 0000000017f00000 (ACPI NVS) BIOS-e820: 0000000017f00000 - 0000000020000000 (reserved) BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) ACPI: RSDP (v000 HP ) @ 0x00000000000f8040 ACPI: RSDT (v001 HP 3093 0x20041209 LTP 0x00000000) @ 0x0000000017ef8ab7 ACPI: FADT (v001 HP 3093 0x20041209 PTL 0x0000005f) @ 0x0000000017efee09 ACPI: SSDT (v001 PTLTD POWERNOW 0x20041209 LTP 0x00000001) @ 0x0000000017efee7d ACPI: MADT (v001 PTLTD 3093 0x20041209 LTP 0x00000000) @ 0x0000000017efef74 ACPI: MCFG (v001 PTLTD MCFG 0x20041209 LTP 0x00000000) @ 0x0000000017efefc4 ACPI: DSDT (v001 HP 3091 0x20041209 MSFT 0x0100000e) @ 0x0000000000000000 Scanning NUMA topology in Northbridge 24 Number of nodes 1 Node 0 MemBase 0000000000000000 Limit 0000000017ef0000 Using 63 for the hash shift. Using node hash shift of 63 Bootmem setup node 0 0000000000000000-0000000017ef0000 On node 0 totalpages: 94927 DMA zone: 2275 pages, LIFO batch:0 DMA32 zone: 92652 pages, LIFO batch:31 Normal zone: 0 pages, LIFO batch:0 HighMem zone: 0 pages, LIFO batch:0 ACPI: PM-Timer IO Port: 0x8008 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Processor #0 15:4 APIC version 16 ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 1, version 33, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 21 low level) Setting APIC routing to physical flat Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at 30000000 (gap: 20000000:dec00000) Checking aperture... CPU 0: aperture @ 9c6000000 size 32 MB Aperture from northbridge cpu 0 too small (32 MB) No AGP bridge found SMP: Allowing 3 CPUs, 2 hotplug CPUs Built 1 zonelists Kernel command line: root=/dev/hda5 reserve=0xc020a000,0x5000 vga=0x318 video=vesafb:ywrap,mtrr,1024x768-32@72 splash=silent,fadein,theme:livecd-2005.1,tty:12 quiet CONSOLE=/dev/tty1 Initializing CPU#0 PID hash table entries: 2048 (order: 11, 65536 bytes) time.c: Using 3.579545 MHz PM timer. time.c: Detected 1994.242 MHz processor. Console: colour dummy device 80x25 Dentry cache hash table entries: 65536 (order: 7, 524288 bytes) Inode-cache hash table entries: 32768 (order: 6, 262144 bytes) Memory: 377484k/392128k available (4011k kernel code, 14256k reserved, 1706k data, 240k init) Calibrating delay using timer specific routine.. 3996.78 BogoMIPS (lpj=7993576) Security Framework v1.0.0 initialized SELinux: Initializing. SELinux: Starting in permissive mode selinux_register_security: Registering secondary module capability Capability LSM initialized as secondary Failure registering Root Plug module with the kernel selinux_register_security: There is already a secondary security module registered. Failure registering Root Plug module with primary security module. Mount-cache hash table entries: 256 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 1024K (64 bytes/line) CPU 0(1) -> Node 0 -> Core 0 mtrr: v2.0 (20020519) Using local APIC timer interrupts. Detected 12.464 MHz APIC timer. Brought up 1 CPUs time.c: Using PIT/TSC based timekeeping. testing NMI watchdog ... OK. checking if image is initramfs... it is NET: Registered protocol family 16 ACPI: bus type pci registered PCI: Using configuration type 1 PCI: Using MMCONFIG at e0000000 ACPI: Subsystem revision 20050902 ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) PCI: Scanning bus 0000:00 PCI: Found 0000:00:00.0 [1002/5950] 000600 00 PCI: Calling quirk ffffffff80309dcb for 0000:00:00.0 PCI: Calling quirk ffffffff80454d75 for 0000:00:00.0 PCI: Calling quirk ffffffff80454a83 for 0000:00:00.0 PCI: Found 0000:00:01.0 [1002/5a3f] 000604 01 PCI: Calling quirk ffffffff80309dcb for 0000:00:01.0 PCI: Calling quirk ffffffff80454d75 for 0000:00:01.0 PCI: Calling quirk ffffffff80454a83 for 0000:00:01.0 PCI: Found 0000:00:13.0 [1002/4374] 000c03 00 PCI: Calling quirk ffffffff80309dcb for 0000:00:13.0 PCI: Calling quirk ffffffff80454d75 for 0000:00:13.0 PCI: Calling quirk ffffffff80454a83 for 0000:00:13.0 PCI: Found 0000:00:13.1 [1002/4375] 000c03 00 PCI: Calling quirk ffffffff80309dcb for 0000:00:13.1 PCI: Calling quirk ffffffff80454d75 for 0000:00:13.1 PCI: Calling quirk ffffffff80454a83 for 0000:00:13.1 PCI: Found 0000:00:13.2 [1002/4373] 000c03 00 PCI: Calling quirk ffffffff80309dcb for 0000:00:13.2 PCI: Calling quirk ffffffff80454d75 for 0000:00:13.2 PCI: Calling quirk ffffffff80454a83 for 0000:00:13.2 PCI: Found 0000:00:14.0 [1002/4372] 000c05 00 PCI: Calling quirk ffffffff80309dcb for 0000:00:14.0 PCI: Calling quirk ffffffff80454d75 for 0000:00:14.0 PCI: Calling quirk ffffffff80454a83 for 0000:00:14.0 PCI: Found 0000:00:14.1 [1002/4376] 000101 00 PCI: Calling quirk ffffffff80309dcb for 0000:00:14.1 PCI: Ignoring BAR0-3 of IDE controller 0000:00:14.1 PCI: Calling quirk ffffffff80454d75 for 0000:00:14.1 PCI: Calling quirk ffffffff80454a83 for 0000:00:14.1 PCI: Found 0000:00:14.3 [1002/4377] 000601 00 PCI: Calling quirk ffffffff80309dcb for 0000:00:14.3 PCI: Calling quirk ffffffff80454d75 for 0000:00:14.3 PCI: Calling quirk ffffffff80454a83 for 0000:00:14.3 PCI: Found 0000:00:14.4 [1002/4371] 000604 01 PCI: Calling quirk ffffffff80309dcb for 0000:00:14.4 PCI: Calling quirk ffffffff80454d75 for 0000:00:14.4 PCI: Calling quirk ffffffff80454a83 for 0000:00:14.4 PCI: Found 0000:00:14.5 [1002/4370] 000401 00 PCI: Calling quirk ffffffff80309dcb for 0000:00:14.5 PCI: Calling quirk ffffffff80454d75 for 0000:00:14.5 PCI: Calling quirk ffffffff80454a83 for 0000:00:14.5 PCI: Found 0000:00:14.6 [1002/4378] 000703 00 PCI: Calling quirk ffffffff80309dcb for 0000:00:14.6 PCI: Calling quirk ffffffff80454d75 for 0000:00:14.6 PCI: Calling quirk ffffffff80454a83 for 0000:00:14.6 PCI: Found 0000:00:18.0 [1022/1100] 000600 00 PCI: Calling quirk ffffffff80309dcb for 0000:00:18.0 PCI: Calling quirk ffffffff80454d75 for 0000:00:18.0 PCI: Calling quirk ffffffff80454a83 for 0000:00:18.0 PCI: Found 0000:00:18.1 [1022/1101] 000600 00 PCI: Calling quirk ffffffff80309dcb for 0000:00:18.1 PCI: Calling quirk ffffffff80454d75 for 0000:00:18.1 PCI: Calling quirk ffffffff80454a83 for 0000:00:18.1 PCI: Found 0000:00:18.2 [1022/1102] 000600 00 PCI: Calling quirk ffffffff80309dcb for 0000:00:18.2 PCI: Calling quirk ffffffff80454d75 for 0000:00:18.2 PCI: Calling quirk ffffffff80454a83 for 0000:00:18.2 PCI: Found 0000:00:18.3 [1022/1103] 000600 00 PCI: Calling quirk ffffffff80309dcb for 0000:00:18.3 PCI: Calling quirk ffffffff80454d75 for 0000:00:18.3 PCI: Calling quirk ffffffff80454a83 for 0000:00:18.3 PCI: Fixups for bus 0000:00 PCI: Scanning behind PCI bridge 0000:00:01.0, config 010100, pass 0 PCI: Scanning bus 0000:01 PCI: Found 0000:01:05.0 [1002/5955] 000300 00 PCI: Calling quirk ffffffff80309dcb for 0000:01:05.0 PCI: Calling quirk ffffffff80454d75 for 0000:01:05.0 Boot video device is 0000:01:05.0 PCI: Calling quirk ffffffff80454a83 for 0000:01:05.0 PCI: Fixups for bus 0000:01 PCI: Bus scan for 0000:01 returning with max=01 PCI: Scanning behind PCI bridge 0000:00:14.4, config 050500, pass 0 PCI: Scanning bus 0000:05 PCI: Found 0000:05:00.0 [10ec/8139] 000200 00 PCI: Calling quirk ffffffff80309dcb for 0000:05:00.0 PCI: Calling quirk ffffffff80454d75 for 0000:05:00.0 PCI: Calling quirk ffffffff80454a83 for 0000:05:00.0 PCI: Found 0000:05:02.0 [14e4/4318] 000280 00 PCI: Calling quirk ffffffff80309dcb for 0000:05:02.0 PCI: Calling quirk ffffffff80454d75 for 0000:05:02.0 PCI: Calling quirk ffffffff80454a83 for 0000:05:02.0 PCI: Found 0000:05:09.0 [104c/8031] 000607 02 PCI: Calling quirk ffffffff80309dcb for 0000:05:09.0 PCI: Calling quirk ffffffff80454d75 for 0000:05:09.0 PCI: Calling quirk ffffffff80454a83 for 0000:05:09.0 PCI: Found 0000:05:09.2 [104c/8032] 000c00 00 PCI: Calling quirk ffffffff80309dcb for 0000:05:09.2 PCI: Calling quirk ffffffff80454dfc for 0000:05:09.2 PCI: Calling quirk ffffffff80454d75 for 0000:05:09.2 PCI: Calling quirk ffffffff80454a83 for 0000:05:09.2 PCI: Found 0000:05:09.3 [104c/8033] 000180 00 PCI: Calling quirk ffffffff80309dcb for 0000:05:09.3 PCI: Calling quirk ffffffff80454d75 for 0000:05:09.3 PCI: Calling quirk ffffffff80454a83 for 0000:05:09.3 PCI: Found 0000:05:09.4 [104c/8034] 000805 00 PCI: Calling quirk ffffffff80309dcb for 0000:05:09.4 PCI: Calling quirk ffffffff80454d75 for 0000:05:09.4 PCI: Calling quirk ffffffff80454a83 for 0000:05:09.4 PCI: Fixups for bus 0000:05 PCI: Transparent bridge - 0000:00:14.4 PCI: Scanning behind PCI bridge 0000:05:09.0, config 000000, pass 0 PCI: Scanning behind PCI bridge 0000:05:09.0, config 000000, pass 1 PCI: Bus scan for 0000:05 returning with max=09 PCI: Scanning behind PCI bridge 0000:00:01.0, config 010100, pass 1 PCI: Scanning behind PCI bridge 0000:00:14.4, config 050500, pass 1 PCI: Bus scan for 0000:00 returning with max=09 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKB] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKC] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKD] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKE] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKF] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKG] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKH] (IRQs 10 11) *0, disabled. ACPI-0339: *** Error: Looking up [UPRS] in namespace, AE_NOT_FOUND search_node ffff81000165b400 start_node ffff81000165b400 return_node 0000000000000000 ACPI-0508: *** Error: Method execution failed [\_SB_.PCI0.LPC0.LNKU._PRS] (Node ffff81000165b400), AE_NOT_FOUND ACPI: Embedded Controller [EC0] (gpe 24) ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT] Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init pnp: ACPI device : hid PNP0C02 pnp: ACPI device : hid PNP0200 pnp: ACPI device : hid PNP0C04 pnp: ACPI device : hid PNP0B00 pnp: ACPI device : hid PNP0800 pnp: ACPI device : hid PNP0303 pnp: ACPI device : hid SYN011C pnp: ACPI device : hid PNP0C02 pnp: ACPI device : hid PNP0C01 pnp: ACPI device : hid PNP0C14 pnp: PnP ACPI: found 10 devices SCSI subsystem initialized usbcore: registered new driver usbfs usbcore: registered new driver hub PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report Bluetooth: Core ver 2.8 NET: Registered protocol family 31 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized PCI-DMA: Disabling IOMMU. pnp: the driver 'system' has been registered pnp: match found with the PnP device '00:00' and the driver 'system' pnp: match found with the PnP device '00:07' and the driver 'system' pnp: 00:07: ioport range 0x1080-0x1080 has been reserved pnp: 00:07: ioport range 0x220-0x22f has been reserved pnp: 00:07: ioport range 0x40b-0x40b has been reserved pnp: 00:07: ioport range 0x4d0-0x4d1 has been reserved pnp: match found with the PnP device '00:08' and the driver 'system' got res [c0120000:c013ffff] bus [c0120000:c013ffff] flags 7202 for BAR 6 of 0000:01:05.0 PCI: Bridge: 0000:00:01.0 IO window: 9000-9fff MEM window: c0100000-c01fffff PREFETCH window: c8000000-cfffffff got res [c020a000:c020afff] bus [c020a000:c020afff] flags 200 for BAR 0 of 0000:05:09.0 PCI: moved device 0000:05:09.0 resource 0 (200) to c020a000 PCI: Bus 6, cardbus bridge: 0000:05:09.0 IO window: 0000a400-0000a4ff IO window: 0000a800-0000a8ff PREFETCH window: 30000000-31ffffff MEM window: 32000000-33ffffff PCI: Bridge: 0000:00:14.4 IO window: a000-afff MEM window: c0200000-c02fffff PREFETCH window: 30000000-31ffffff GSI 16 sharing vector 0xB9 and IRQ 16 ACPI: PCI Interrupt 0000:05:09.0[A] -> GSI 17 (level, low) -> IRQ 185 PCI: Setting latency timer of device 0000:05:09.0 to 64 IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $ Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 512 (order 0, 4096 bytes) Installing knfsd (copyright (C) 1996 okir@monad.swb.de). NTFS driver 2.1.25 [Flags: R/W]. JFS: nTxBlock = 2949, nTxLock = 23592 SGI XFS with large block/inode numbers, no debug enabled SELinux: Registering netfilter hooks seclvl: seclvl_init: seclvl: Failure registering with the kernel. selinux_register_security: There is already a secondary security module registered. seclvl: seclvl_init: seclvl: Failure registering with primary security module. seclvl: Error during initialization: rc = [-22] Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered PCI: Calling quirk ffffffff80309cff for 0000:00:00.0 PCI: Calling quirk ffffffff8043292b for 0000:00:00.0 PCI: Calling quirk ffffffff80309cff for 0000:00:01.0 PCI: Calling quirk ffffffff8043292b for 0000:00:01.0 PCI: Calling quirk ffffffff80309cff for 0000:00:13.0 PCI: Calling quirk ffffffff8043292b for 0000:00:13.0 PCI: Calling quirk ffffffff80309cff for 0000:00:13.1 PCI: Calling quirk ffffffff8043292b for 0000:00:13.1 PCI: Calling quirk ffffffff80309cff for 0000:00:13.2 PCI: Calling quirk ffffffff8043292b for 0000:00:13.2 PCI: Calling quirk ffffffff80309cff for 0000:00:14.0 PCI: Calling quirk ffffffff8043292b for 0000:00:14.0 PCI: Calling quirk ffffffff80309cff for 0000:00:14.1 PCI: Calling quirk ffffffff8043292b for 0000:00:14.1 PCI: Calling quirk ffffffff80309cff for 0000:00:14.3 PCI: Calling quirk ffffffff8043292b for 0000:00:14.3 PCI: Calling quirk ffffffff80309cff for 0000:00:14.4 PCI: Calling quirk ffffffff8043292b for 0000:00:14.4 PCI: Calling quirk ffffffff80309cff for 0000:00:14.5 PCI: Calling quirk ffffffff8043292b for 0000:00:14.5 PCI: Calling quirk ffffffff80309cff for 0000:00:14.6 PCI: Calling quirk ffffffff8043292b for 0000:00:14.6 PCI: Calling quirk ffffffff80309cff for 0000:00:18.0 PCI: Calling quirk ffffffff8043292b for 0000:00:18.0 PCI: Calling quirk ffffffff80309cff for 0000:00:18.1 PCI: Calling quirk ffffffff8043292b for 0000:00:18.1 PCI: Calling quirk ffffffff80309cff for 0000:00:18.2 PCI: Calling quirk ffffffff8043292b for 0000:00:18.2 PCI: Calling quirk ffffffff80309cff for 0000:00:18.3 PCI: Calling quirk ffffffff8043292b for 0000:00:18.3 PCI: Calling quirk ffffffff80309cff for 0000:01:05.0 PCI: Calling quirk ffffffff8043292b for 0000:01:05.0 PCI: Calling quirk ffffffff80309cff for 0000:05:00.0 PCI: Calling quirk ffffffff8043292b for 0000:05:00.0 PCI: Calling quirk ffffffff80309cff for 0000:05:02.0 PCI: Calling quirk ffffffff8043292b for 0000:05:02.0 PCI: Calling quirk ffffffff80309cff for 0000:05:09.0 PCI: Calling quirk ffffffff8043292b for 0000:05:09.0 PCI: Calling quirk ffffffff80309cff for 0000:05:09.2 PCI: Calling quirk ffffffff8043292b for 0000:05:09.2 PCI: Calling quirk ffffffff80309cff for 0000:05:09.3 PCI: Calling quirk ffffffff8043292b for 0000:05:09.3 PCI: Calling quirk ffffffff80309cff for 0000:05:09.4 PCI: Calling quirk ffffffff8043292b for 0000:05:09.4 vesafb: framebuffer at 0xc8000000, mapped to 0xffffc20010300000, using 4608k, total 131072k vesafb: mode is 1024x768x24, linelength=3072, pages=55 vesafb: scrolling: redraw vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0 vesafb: Mode is not VGA compatible Console: switching to colour frame buffer device 128x48 fbsplash: console 0 using theme 'livecd-2005.1' fb0: VESA VGA frame buffer device vga16fb: initializing vga16fb: mapped to 0xffff8100000a0000 fb1: VGA16 VGA frame buffer device ACPI: AC Adapter [ACAD] (on-line) ACPI: Battery Slot [BAT1] (battery present) ACPI: Power Button (FF) [PWRF] ACPI: Power Button (CM) [PWRB] ACPI: Sleep Button (CM) [SLPB] ACPI: Lid Switch [LID] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no) ACPI: CPU0 (power states: C1[C1] C2[C2]) ACPI: Processor [CPU0] (supports 8 throttling states) ACPI: Thermal Zone [THRM] (70 C) Real Time Clock Driver v1.12 Software Watchdog Timer: 0.07 initialized. soft_noboot=0 soft_margin=60 sec (nowayout= 0) Linux agpgart interface v0.101 (c) Dave Jones pnp: the driver 'i8042 kbd' has been registered pnp: match found with the PnP device '00:05' and the driver 'i8042 kbd' pnp: the driver 'i8042 aux' has been registered pnp: match found with the PnP device '00:06' and the driver 'i8042 aux' PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12 serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled pnp: the driver 'serial' has been registered ACPI: PCI Interrupt 0000:00:14.6[B] -> GSI 17 (level, low) -> IRQ 185 ACPI: PCI interrupt for device 0000:00:14.6 disabled mice: PS/2 mouse device common for all mice input: PC Speaker as /class/input/input0 input: AT Translated Set 2 keyboard as /class/input/input1 Synaptics Touchpad, model: 1, fw: 5.10, id: 0x258eb1, caps: 0xa04713/0x0 input: SynPS/2 Synaptics TouchPad as /class/input/input2 floppy0: no floppy controllers found RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize loop: loaded (max 8 devices) Intel(R) PRO/1000 Network Driver - version 6.1.16-k2 Copyright (c) 1999-2005 Intel Corporation. e100: Intel(R) PRO/100 Network Driver, 3.4.14-k4-NAPI e100: Copyright(c) 1999-2005 Intel Corporation forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.48. 8139too Fast Ethernet driver 0.9.27 GSI 17 sharing vector 0xC1 and IRQ 17 ACPI: PCI Interrupt 0000:05:00.0[A] -> GSI 18 (level, low) -> IRQ 193 eth0: RealTek RTL8139 at 0xffffc20000022000, 00:16:36:13:cd:af, IRQ 193 eth0: Identified 8139 chip type 'RTL-8100B/8139D' tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> netconsole: not configured, aborting Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ATIIXP: IDE controller at PCI slot 0000:00:14.1 GSI 18 sharing vector 0xC9 and IRQ 18 ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 201 ATIIXP: chipset revision 128 ATIIXP: not 100% native mode: will probe irqs later ide0: BM-DMA at 0x8410-0x8417, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0x8418-0x841f, BIOS settings: hdc:DMA, hdd:pio Probing IDE interface ide0... hda: TOSHIBA MK1031GAS, ATA DISK drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... hdc: PIONEER DVDRW DVR-K15, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 pnp: the driver 'ide' has been registered hda: max request size: 128KiB hda: 195371568 sectors (100030 MB), CHS=65535/16/63, UDMA(100) hda: cache flushes supported hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 hda8 hda9 hda10 hda11 hda12 hda13 hda14 > hdc: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2000kB Cache, DMA Uniform CD-ROM driver Revision: 3.20 libata version 1.20 loaded. Fusion MPT base driver 3.03.04 Copyright (c) 1999-2005 LSI Logic Corporation Fusion MPT SPI Host driver 3.03.04 ACPI: PCI Interrupt 0000:05:09.0[A] -> GSI 17 (level, low) -> IRQ 185 Yenta: CardBus bridge found at 0000:05:09.0 [103c:3091] Yenta: Enabling burst memory read transactions Yenta: Using CSCINT to route CSC interrupts to PCI Yenta: Routing CardBus interrupts to PCI Yenta TI: socket 0000:05:09.0, mfunc 0x01a01b22, devctl 0x64 Yenta: ISA IRQ mask 0x0ef8, PCI irq 185 Socket status: 30000820 pcmcia: parent PCI bridge I/O window: 0xa000 - 0xafff pcmcia: parent PCI bridge Memory window: 0xc0200000 - 0xc02fffff pcmcia: parent PCI bridge Memory window: 0x30000000 - 0x31ffffff usbcore: registered new driver usblp drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver Initializing USB Mass Storage driver... usbcore: registered new driver usb-storage USB Mass Storage support registered. usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver i2c /dev entries driver device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com Intel 810 + AC97 Audio, version 1.01, 15:18:30 Feb 1 2006 oprofile: using NMI interrupt. NET: Registered protocol family 2 IP route cache hash table entries: 4096 (order: 3, 32768 bytes) TCP established hash table entries: 16384 (order: 6, 262144 bytes) TCP bind hash table entries: 16384 (order: 6, 262144 bytes) TCP: Hash tables configured (established 16384 bind 16384) TCP reno registered TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 10 IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 powernow-k8: Found 1 AMD Athlon 64 / Opteron processors (version 1.50.4) powernow-k8: 0 : fid 0xc (2000 MHz), vid 0x4 (1450 mV) powernow-k8: 1 : fid 0xa (1800 MHz), vid 0x6 (1400 mV) powernow-k8: 2 : fid 0x8 (1600 MHz), vid 0x8 (1350 mV) powernow-k8: 3 : fid 0x0 (800 MHz), vid 0x16 (1000 mV) cpu_init done, current fid 0xc, vid 0x4 ACPI wakeup devices: KBC0 MSE0 P2P AUDO ACPI: (supports S0 S3 S4 S5) ReiserFS: hda5: found reiserfs format "3.6" with standard journal ReiserFS: hda5: using ordered data mode ReiserFS: hda5: journal params: device hda5, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: hda5: checking transaction log (hda5) ReiserFS: hda5: Using r5 hash to sort names VFS: Mounted root (reiserfs filesystem) readonly. Freeing unused kernel memory: 240k freed pccard: CardBus card inserted into slot 0 Adding 979956k swap on /dev/hda3. Priority:-1 extents:1 across:979956k fbsplash: switched splash state to 'on' on console 0 ndiswrapper version 1.8 loaded (preempt=no,smp=yes) ndiswrapper (load_pe_images:571): fixing KI_USER_SHARED_DATA address in the driver ndiswrapper: driver bcmwl5 (Broadcom,02/11/2005, 3.100.64.0) loaded GSI 19 sharing vector 0xD1 and IRQ 19 ACPI: PCI Interrupt 0000:05:02.0[A] -> GSI 20 (level, low) -> IRQ 209 ndiswrapper: using irq 209 wlan0: vendor: '' wlan0: ndiswrapper ethernet device 00:14:a5:69:0e:b4 using driver bcmwl5, 14E4:4318.5.conf wlan0: encryption modes supported: WEP; TKIP with WPA, WPA2, WPA2PSK; AES/CCMP with WPA, WPA2, WPA2PSK [fglrx] Maximum main memory to use for locked dma buffers: 307 MBytes. ACPI: PCI Interrupt 0000:01:05.0[A] -> GSI 17 (level, low) -> IRQ 185 [fglrx] module loaded - fglrx 8.22.5 [Feb 7 2006] on minor 0 ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) ohci_hcd: block sizes: ed 80 td 96 GSI 20 sharing vector 0xD9 and IRQ 20 ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> IRQ 217 ohci_hcd 0000:00:13.0: OHCI Host Controller drivers/usb/core/inode.c: creating file 'devices' drivers/usb/core/inode.c: creating file '001' ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1 ohci_hcd 0000:00:13.0: irq 217, io mem 0xc0000000 ohci_hcd 0000:00:13.0: resetting from state 'reset', control = 0x0 ohci_hcd 0000:00:13.0: OHCI controller state ohci_hcd 0000:00:13.0: OHCI 1.0, NO legacy support registers ohci_hcd 0000:00:13.0: control 0x083 HCFS=operational CBSR=3 ohci_hcd 0000:00:13.0: cmdstatus 0x00000 SOC=0 ohci_hcd 0000:00:13.0: intrstatus 0x00000044 RHSC SF ohci_hcd 0000:00:13.0: intrenable 0x8000001a MIE UE RD WDH ohci_hcd 0000:00:13.0: hcca frame #0005 ohci_hcd 0000:00:13.0: roothub.a 02000204 POTPGT=2 NPS NDP=4(4) ohci_hcd 0000:00:13.0: roothub.b 00000000 PPCM=0000 DR=0000 ohci_hcd 0000:00:13.0: roothub.status 00008000 DRWE ohci_hcd 0000:00:13.0: roothub.portstatus [0] 0x00010301 CSC LSDA PPS CCS ohci_hcd 0000:00:13.0: roothub.portstatus [1] 0x00000100 PPS ohci_hcd 0000:00:13.0: roothub.portstatus [2] 0x00000100 PPS ohci_hcd 0000:00:13.0: roothub.portstatus [3] 0x00000100 PPS ohci_hcd 0000:00:13.0: created debug files usb usb1: default language 0x0409 usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: OHCI Host Controller usb usb1: Manufacturer: Linux 2.6.15-gentoo-r1 ohci_hcd usb usb1: SerialNumber: 0000:00:13.0 usb usb1: hotplug usb usb1: adding 1-0:1.0 (config #1, interface 0) usb 1-0:1.0: hotplug hub 1-0:1.0: usb_probe_interface hub 1-0:1.0: usb_probe_interface - got id hub 1-0:1.0: USB hub found hub 1-0:1.0: 4 ports detected hub 1-0:1.0: standalone hub hub 1-0:1.0: no power switching (usb 1.0) hub 1-0:1.0: global over-current protection hub 1-0:1.0: power on to power good time: 4ms hub 1-0:1.0: local power source is good hub 1-0:1.0: no over-current condition exists hub 1-0:1.0: state 5 ports 4 chg 0000 evt 0000 drivers/usb/core/inode.c: creating file '001' ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [0] = 0x00010301 CSC LSDA PPS CCS hub 1-0:1.0: port 1, status 0301, change 0001, 1.5 Mb/s ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 19 (level, low) -> IRQ 217 ohci_hcd 0000:00:13.1: OHCI Host Controller drivers/usb/core/inode.c: creating file '002' ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:13.1: irq 217, io mem 0xc0001000 ohci_hcd 0000:00:13.1: resetting from state 'reset', control = 0x0 ohci_hcd 0000:00:13.1: OHCI controller state ohci_hcd 0000:00:13.1: OHCI 1.0, NO legacy support registers ohci_hcd 0000:00:13.1: control 0x083 HCFS=operational CBSR=3 ohci_hcd 0000:00:13.1: cmdstatus 0x00000 SOC=0 ohci_hcd 0000:00:13.1: intrstatus 0x00000044 RHSC SF ohci_hcd 0000:00:13.1: intrenable 0x8000001a MIE UE RD WDH ohci_hcd 0000:00:13.1: hcca frame #0005 ohci_hcd 0000:00:13.1: roothub.a 02000204 POTPGT=2 NPS NDP=4(4) ohci_hcd 0000:00:13.1: roothub.b 00000000 PPCM=0000 DR=0000 ohci_hcd 0000:00:13.1: roothub.status 00008000 DRWE ohci_hcd 0000:00:13.1: roothub.portstatus [0] 0x00000100 PPS ohci_hcd 0000:00:13.1: roothub.portstatus [1] 0x00000100 PPS ohci_hcd 0000:00:13.1: roothub.portstatus [2] 0x00010101 CSC PPS CCS ohci_hcd 0000:00:13.1: roothub.portstatus [3] 0x00000100 PPS ohci_hcd 0000:00:13.1: created debug files usb usb2: default language 0x0409 usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: OHCI Host Controller usb usb2: Manufacturer: Linux 2.6.15-gentoo-r1 ohci_hcd usb usb2: SerialNumber: 0000:00:13.1 usb usb2: hotplug usb usb2: adding 2-0:1.0 (config #1, interface 0) usb 2-0:1.0: hotplug hub 2-0:1.0: usb_probe_interface hub 2-0:1.0: usb_probe_interface - got id hub 2-0:1.0: USB hub found hub 2-0:1.0: 4 ports detected hub 2-0:1.0: standalone hub hub 2-0:1.0: no power switching (usb 1.0) hub 2-0:1.0: global over-current protection hub 2-0:1.0: power on to power good time: 4ms hub 2-0:1.0: local power source is good hub 2-0:1.0: no over-current condition exists hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301 drivers/usb/core/inode.c: creating file '001' ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [0] = 0x00100303 PRSC LSDA PPS PES CCS ehci_hcd: block sizes: qh 160 qtd 96 itd 192 sitd 96 ACPI: PCI Interrupt 0000:00:13.2[A] -> GSI 19 (level, low) -> IRQ 217 ehci_hcd 0000:00:13.2: EHCI Host Controller ehci_hcd 0000:00:13.2: reset hcs_params 0x2408 dbg=0 cc=2 pcc=4 ordered !ppc ports=8 ehci_hcd 0000:00:13.2: reset hcc_params a012 thresh 1 uframes 256/512/1024 ehci_hcd 0000:00:13.2: capability 0001 at a0 ehci_hcd 0000:00:13.2: MWI active drivers/usb/core/inode.c: creating file '003' ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 3 ehci_hcd 0000:00:13.2: irq 217, io mem 0xc0002000 ehci_hcd 0000:00:13.2: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT ehci_hcd 0000:00:13.2: init command 010009 (park)=0 ithresh=1 period=256 RUN ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb3: default language 0x0409 usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb3: Product: EHCI Host Controller usb usb3: Manufacturer: Linux 2.6.15-gentoo-r1 ehci_hcd usb usb3: SerialNumber: 0000:00:13.2 usb usb3: hotplug usb usb3: adding 3-0:1.0 (config #1, interface 0) usb 3-0:1.0: hotplug hub 3-0:1.0: usb_probe_interface hub 3-0:1.0: usb_probe_interface - got id hub 3-0:1.0: USB hub found hub 3-0:1.0: 8 ports detected hub 3-0:1.0: standalone hub hub 3-0:1.0: no power switching (usb 1.0) hub 3-0:1.0: individual port over-current protection hub 3-0:1.0: Single TT hub 3-0:1.0: TT requires at most 8 FS bit times (666 ns) hub 3-0:1.0: power on to power good time: 20ms hub 3-0:1.0: local power source is good usb 1-1: new low speed USB device using ohci_hcd and address 2 ohci_hcd 0000:00:13.0: urb ffff810012cd60c0 path 1 ep0in 5ec20000 cc 5 --> status -110 ohci_hcd 0000:00:13.0: urb ffff810012cd60c0 path 1 ep0in 5ec20000 cc 5 --> status -110 ohci_hcd 0000:00:13.0: urb ffff810012cd60c0 path 1 ep0in 5ec20000 cc 5 --> status -110 ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [0] = 0x00030100 PESC CSC PPS hub 2-0:1.0: state 5 ports 4 chg 0000 evt 0000 ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [2] = 0x00010100 CSC PPS hub 2-0:1.0: port 3, status 0100, change 0001, 12 Mb/s drivers/usb/core/inode.c: creating file '001' hub 2-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x100 hub 1-0:1.0: state 5 ports 4 chg 0000 evt 0002 usbcore: registered new driver usbserial ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [0] = 0x00030100 PESC CSC PPS hub 1-0:1.0: port 1, status 0100, change 0003, 12 Mb/s drivers/usb/serial/usb-serial.c: USB Serial support registered for generic hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100 hub 3-0:1.0: state 5 ports 8 chg 0000 evt 0042 usbcore: registered new driver usbserial_generic drivers/usb/serial/usb-serial.c: USB Serial Driver core ehci_hcd 0000:00:13.2: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT hub 3-0:1.0: port 1, status 0501, change 0001, 480 Mb/s CSLIP: code copyright 1989 Regents of the University of California PPP generic driver version 2.4.2 hub 3-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501 ehci_hcd 0000:00:13.2: port 1 low speed --> companion ehci_hcd 0000:00:13.2: GetStatus port 6 status 001803 POWER sig=j CSC CONNECT hub 3-0:1.0: port 6, status 0501, change 0001, 480 Mb/s hub 3-0:1.0: debounce: port 6: total 100ms stable 100ms status 0x501 ehci_hcd 0000:00:13.2: port 6 full speed --> companion ehci_hcd 0000:00:13.2: GetStatus port 6 status 003801 POWER OWNER sig=j CONNECT hub 1-0:1.0: state 5 ports 4 chg 0000 evt 0002 ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [0] = 0x00010301 CSC LSDA PPS CCS hub 1-0:1.0: port 1, status 0301, change 0001, 1.5 Mb/s hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301 ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [0] = 0x00100303 PRSC LSDA PPS PES CCS usb 1-1: new low speed USB device using ohci_hcd and address 3 ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [0] = 0x00100303 PRSC LSDA PPS PES CCS usb 1-1: skipped 1 descriptor after interface usb 1-1: new device strings: Mfr=0, Product=0, SerialNumber=0 usb 1-1: hotplug usb 1-1: adding 1-1:1.0 (config #1, interface 0) usb 1-1:1.0: hotplug usbhid 1-1:1.0: usb_probe_interface usbhid 1-1:1.0: usb_probe_interface - got id input: HID 1241:1177 as /class/input/input3 input: USB HID v1.10 Mouse [HID 1241:1177] on usb-0000:00:13.0-1 drivers/usb/core/inode.c: creating file '003' hub 3-0:1.0: state 5 ports 8 chg 0000 evt 0000 hub 2-0:1.0: state 5 ports 4 chg 0000 evt 0008 ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [2] = 0x00010101 CSC PPS CCS hub 2-0:1.0: port 3, status 0101, change 0001, 12 Mb/s hub 2-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x101 ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [2] = 0x00100103 PRSC PPS PES CCS usb 2-3: new full speed USB device using ohci_hcd and address 2 ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [2] = 0x00100103 PRSC PPS PES CCS usb 2-3: skipped 1 descriptor after interface usb 2-3: default language 0x0409 usb 2-3: new device strings: Mfr=1, Product=2, SerialNumber=0 usb 2-3: Product: HP integrated Bluetooth module usb 2-3: Manufacturer: Broadcom usb 2-3: hotplug usb 2-3: adding 2-3:1.0 (config #1, interface 0) usb 2-3:1.0: hotplug usbserial_generic 2-3:1.0: usb_probe_interface usbserial_generic 2-3:1.0: usb_probe_interface - got id usb 2-3: adding 2-3:1.1 (config #1, interface 1) usb 2-3:1.1: hotplug usbserial_generic 2-3:1.1: usb_probe_interface usbserial_generic 2-3:1.1: usb_probe_interface - got id usb 2-3: adding 2-3:1.2 (config #1, interface 2) usb 2-3:1.2: hotplug usbserial_generic 2-3:1.2: usb_probe_interface usbserial_generic 2-3:1.2: usb_probe_interface - got id usb 2-3: adding 2-3:1.3 (config #1, interface 3) usb 2-3:1.3: hotplug usbserial_generic 2-3:1.3: usb_probe_interface usbserial_generic 2-3:1.3: usb_probe_interface - got id drivers/usb/core/inode.c: creating file '002' hub 1-0:1.0: state 5 ports 4 chg 0000 evt 0002 Bluetooth: HCI USB driver ver 2.9 hci_usb 2-3:1.0: usb_probe_interface hci_usb 2-3:1.0: usb_probe_interface - got id hci_usb 2-3:1.2: usb_probe_interface hci_usb 2-3:1.2: usb_probe_interface - got id hci_usb 2-3:1.3: usb_probe_interface hci_usb 2-3:1.3: usb_probe_interface - got id usbcore: registered new driver hci_usb ReiserFS: hda6: found reiserfs format "3.6" with standard journal ReiserFS: hda6: using ordered data mode ReiserFS: hda6: journal params: device hda6, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: hda6: checking transaction log (hda6) ReiserFS: hda6: Using r5 hash to sort names ReiserFS: hda7: found reiserfs format "3.6" with standard journal ReiserFS: hda7: using ordered data mode ReiserFS: hda7: journal params: device hda7, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: hda7: checking transaction log (hda7) ReiserFS: hda7: Using r5 hash to sort names ReiserFS: hda8: found reiserfs format "3.6" with standard journal ReiserFS: hda8: using ordered data mode ReiserFS: hda8: journal params: device hda8, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: hda8: checking transaction log (hda8) ReiserFS: hda8: Using r5 hash to sort names ReiserFS: hda9: found reiserfs format "3.6" with standard journal ReiserFS: hda9: using ordered data mode ReiserFS: hda9: journal params: device hda9, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: hda9: checking transaction log (hda9) ReiserFS: hda9: Using r5 hash to sort names ReiserFS: hda10: found reiserfs format "3.6" with standard journal ReiserFS: hda10: using ordered data mode ReiserFS: hda10: journal params: device hda10, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: hda10: checking transaction log (hda10) ReiserFS: hda10: Using r5 hash to sort names ReiserFS: hda11: found reiserfs format "3.6" with standard journal ReiserFS: hda11: using ordered data mode ReiserFS: hda11: journal params: device hda11, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: hda11: checking transaction log (hda11) ReiserFS: hda11: Using r5 hash to sort names NTFS volume version 3.1. NTFS-fs error (device hda1): load_system_files(): Volume is dirty. Mounting read-only. Run chkdsk and mount in Windows. NTFS volume version 3.1. NTFS-fs error (device hda12): load_system_files(): Volume is dirty. Mounting read-only. Run chkdsk and mount in Windows. ReiserFS: hda14: found reiserfs format "3.6" with standard journal ReiserFS: hda14: using ordered data mode ReiserFS: hda14: journal params: device hda14, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: hda14: checking transaction log (hda14) ReiserFS: hda14: Using r5 hash to sort names ACPI: PCI Interrupt 0000:00:14.5[B] -> GSI 17 (level, low) -> IRQ 185 ACPI: PCI Interrupt 0000:00:14.6[B] -> GSI 17 (level, low) -> IRQ 185 PCI: Enabling bus mastering for device 0000:00:14.6 MC'97 0 converters and GPIO not ready (0x1) 8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004) ohci1394: $Rev: 1313 $ Ben Collins <bcollins@debian.org> GSI 22 sharing vector 0xE1 and IRQ 22 ACPI: PCI Interrupt 0000:05:09.2[C] -> GSI 22 (level, low) -> IRQ 225 PCI: Calling quirk ffffffff80454dfd for 0000:05:09.2 ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[225] MMIO=[c0208800-c0208fff] Max Packet=[2048] USB Universal Host Controller Interface driver v2.3 hcid[11335]: segfault at 0000000000000008 rip 00002aaaaabcd2f0 rsp 00007fffffcf2b10 error 4 Bluetooth: L2CAP ver 2.8 Bluetooth: L2CAP socket layer initialized Bluetooth: RFCOMM socket layer initialized Bluetooth: RFCOMM TTY layer initialized Bluetooth: RFCOMM ver 1.6 wlan0: no IPv6 routers present ip_tables: (C) 2000-2002 Netfilter core team ip_conntrack version 2.4 (1531 buckets, 12248 max) - 312 bytes per conntrack fbsplash: console 1 using theme 'livecd-2005.1' fbsplash: switched splash state to 'on' on console 1 fbsplash: console 2 using theme 'livecd-2005.1' fbsplash: switched splash state to 'on' on console 2 fbsplash: console 3 using theme 'livecd-2005.1' fbsplash: switched splash state to 'on' on console 3 fbsplash: console 4 using theme 'livecd-2005.1' fbsplash: switched splash state to 'on' on console 4 fbsplash: console 5 using theme 'livecd-2005.1' fbsplash: switched splash state to 'on' on console 5 fbsplash: console 6 using theme 'livecd-2005.1' fbsplash: switched splash state to 'on' on console 6 fbsplash: console 7 using theme 'livecd-2005.1' fbsplash: switched splash state to 'on' on console 7 fbsplash: console 8 using theme 'livecd-2005.1' fbsplash: switched splash state to 'on' on console 8 fbsplash: console 9 using theme 'livecd-2005.1' fbsplash: switched splash state to 'on' on console 9 fbsplash: console 10 using theme 'livecd-2005.1' fbsplash: switched splash state to 'on' on console 10 [fglrx] free PCIe = 54804480 [fglrx] max PCIe = 54804480 [fglrx] free LFB = 119468032 [fglrx] max LFB = 119468032 [fglrx] free Inv = 0 [fglrx] max Inv = 0 [fglrx] total Inv = 0 [fglrx] total TIM = 0 [fglrx] total FB = 0 [fglrx] total PCIe = 16384 [fglrx:firegl_lock] *ERROR* Process 14238 is using illegal context 0x00000005 [fglrx] free PCIe = 54804480 [fglrx] max PCIe = 54804480 [fglrx] free LFB = 119468032 [fglrx] max LFB = 119468032 [fglrx] free Inv = 0 [fglrx] max Inv = 0 [fglrx] total Inv = 0 [fglrx] total TIM = 0 [fglrx] total FB = 0 [fglrx] total PCIe = 16384 APIC error on CPU0: 00(40) APIC error on CPU0: 40(40) APIC error on CPU0: 40(40) ohci_hcd 0000:00:13.0: urb ffff810012c70c80 path 1 ep1in 5c160000 cc 5 --> status -110 ohci_hcd 0000:00:13.0: urb ffff810012c70c80 path 1 ep1in 5c160000 cc 5 --> status -110 ohci_hcd 0000:00:13.0: urb ffff810012c70c80 path 1 ep1in 5c160000 cc 5 --> status -110 ohci_hcd 0000:00:13.0: urb ffff810012c70c80 path 1 ep1in 5c160000 cc 5 --> status -110 ohci_hcd 0000:00:13.0: urb ffff810012c70c80 path 1 ep1in 5c160000 cc 5 --> status -110 hub 1-0:1.0: state 5 ports 4 chg 0000 evt 0002 ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [0] = 0x00030100 PESC CSC PPS hub 1-0:1.0: port 1, status 0100, change 0003, 12 Mb/s usb 1-1: USB disconnect, address 3 usb 1-1: usb_disable_device nuking all URBs ohci_hcd 0000:00:13.0: shutdown urb ffff810012c70c80 pipe 40408380 ep1in-intr usb 1-1: unregistering interface 1-1:1.0 usb 1-1:1.0: hotplug usb 1-1: unregistering device usb 1-1: hotplug hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100 APIC error on CPU0: 40(40) hub 3-0:1.0: state 5 ports 8 chg 0000 evt 0008 ehci_hcd 0000:00:13.2: GetStatus port 3 status 001403 POWER sig=k CSC CONNECT hub 3-0:1.0: port 3, status 0501, change 0001, 480 Mb/s hub 3-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x501 ehci_hcd 0000:00:13.2: port 3 low speed --> companion ehci_hcd 0000:00:13.2: GetStatus port 3 status 003002 POWER OWNER sig=se0 CSC hub 1-0:1.0: state 5 ports 4 chg 0000 evt 0004 ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [1] = 0x00010301 CSC LSDA PPS CCS hub 1-0:1.0: port 2, status 0301, change 0001, 1.5 Mb/s hub 1-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x301 ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [1] = 0x00100303 PRSC LSDA PPS PES CCS usb 1-2: new low speed USB device using ohci_hcd and address 4 ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [1] = 0x00100303 PRSC LSDA PPS PES CCS usb 1-2: skipped 1 descriptor after interface usb 1-2: new device strings: Mfr=0, Product=0, SerialNumber=0 usb 1-2: hotplug usb 1-2: adding 1-2:1.0 (config #1, interface 0) usb 1-2:1.0: hotplug usbhid 1-2:1.0: usb_probe_interface usbhid 1-2:1.0: usb_probe_interface - got id input: HID 1241:1177 as /class/input/input4 input: USB HID v1.10 Mouse [HID 1241:1177] on usb-0000:00:13.0-2 drivers/usb/core/inode.c: creating file '004' hub 1-0:1.0: state 5 ports 4 chg 0000 evt 0004 pccard: card ejected from slot 0 PCMCIA: socket ffff810017029048: *** DANGER *** unable to remove socket power APIC error on CPU0: 40(40) pccard: CardBus card inserted into slot 0 APIC error on CPU0: 40(40) APIC error on CPU0: 40(40) APIC error on CPU0: 40(40) APIC error on CPU0: 40(40) APIC error on CPU0: 40(40) APIC error on CPU0: 40(40) APIC error on CPU0: 40(40) | |