lkml.org 
[lkml]   [2006]   [Nov]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Subject[PATCH] IB/ipath - program intconfig register using new HT irq hook
Date
From
Eric's changes to the htirq infrastructure require corresponding
modifications to the ipath HT driver code so that interrupts are still
delivered properly.

Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Roland Dreier <rdreier@cisco.com>

diff -r 69779e2890e3 -r 545156d49f88 drivers/infiniband/hw/ipath/ipath_driver.c
--- a/drivers/infiniband/hw/ipath/ipath_driver.c Wed Nov 08 14:17:04 2006 -0800
+++ b/drivers/infiniband/hw/ipath/ipath_driver.c Wed Nov 08 14:19:27 2006 -0800
@@ -304,7 +304,7 @@ static int __devinit ipath_init_one(stru
}
addr = pci_resource_start(pdev, 0);
len = pci_resource_len(pdev, 0);
- ipath_cdbg(VERBOSE, "regbase (0) %llx len %d irq %x, vend %x/%x "
+ ipath_cdbg(VERBOSE, "regbase (0) %llx len %d pdev->irq %d, vend %x/%x "
"driver_data %lx\n", addr, len, pdev->irq, ent->vendor,
ent->device, ent->driver_data);

@@ -467,15 +467,15 @@ static int __devinit ipath_init_one(stru
* check 0 irq after we return from chip-specific bus setup, since
* that can affect this due to setup
*/
- if (!pdev->irq)
+ if (!dd->ipath_irq)
ipath_dev_err(dd, "irq is 0, BIOS error? Interrupts won't "
"work\n");
else {
- ret = request_irq(pdev->irq, ipath_intr, IRQF_SHARED,
+ ret = request_irq(dd->ipath_irq, ipath_intr, IRQF_SHARED,
IPATH_DRV_NAME, dd);
if (ret) {
ipath_dev_err(dd, "Couldn't setup irq handler, "
- "irq=%u: %d\n", pdev->irq, ret);
+ "irq=%d: %d\n", dd->ipath_irq, ret);
goto bail_iounmap;
}
}
@@ -637,11 +637,10 @@ static void __devexit ipath_remove_one(s
* free up port 0 (kernel) rcvhdr, egr bufs, and eventually tid bufs
* for all versions of the driver, if they were allocated
*/
- if (pdev->irq) {
- ipath_cdbg(VERBOSE,
- "unit %u free_irq of irq %x\n",
- dd->ipath_unit, pdev->irq);
- free_irq(pdev->irq, dd);
+ if (dd->ipath_irq) {
+ ipath_cdbg(VERBOSE, "unit %u free irq %d\n",
+ dd->ipath_unit, dd->ipath_irq);
+ dd->ipath_f_free_irq(dd);
} else
ipath_dbg("irq is 0, not doing free_irq "
"for unit %u\n", dd->ipath_unit);
diff -r 69779e2890e3 -r 545156d49f88 drivers/infiniband/hw/ipath/ipath_iba6110.c
--- a/drivers/infiniband/hw/ipath/ipath_iba6110.c Wed Nov 08 14:17:04 2006 -0800
+++ b/drivers/infiniband/hw/ipath/ipath_iba6110.c Wed Nov 08 14:19:27 2006 -0800
@@ -38,6 +38,7 @@

#include <linux/pci.h>
#include <linux/delay.h>
+#include <linux/htirq.h>

#include "ipath_kernel.h"
#include "ipath_registers.h"
@@ -913,49 +914,40 @@ static void slave_or_pri_blk(struct ipat
}
}

-static int set_int_handler(struct ipath_devdata *dd, struct pci_dev *pdev,
- int pos)
-{
- u32 int_handler_addr_lower;
- u32 int_handler_addr_upper;
- u64 ihandler;
- u32 intvec;
-
- /* use indirection register to get the intr handler */
- pci_write_config_byte(pdev, pos + HT_INTR_REG_INDEX, 0x10);
- pci_read_config_dword(pdev, pos + 4, &int_handler_addr_lower);
- pci_write_config_byte(pdev, pos + HT_INTR_REG_INDEX, 0x11);
- pci_read_config_dword(pdev, pos + 4, &int_handler_addr_upper);
-
- ihandler = (u64) int_handler_addr_lower |
- ((u64) int_handler_addr_upper << 32);
-
- /*
- * kernels with CONFIG_PCI_MSI set the vector in the irq field of
- * struct pci_device, so we use that to program the internal
- * interrupt register (not config space) with that value. The BIOS
- * must still have done the basic MSI setup.
- */
- intvec = pdev->irq;
- /*
- * clear any vector bits there; normally not set but we'll overload
- * this for some debug purposes (setting the HTC debug register
- * value from software, rather than GPIOs), so it might be set on a
- * driver reload.
- */
- ihandler &= ~0xff0000;
- /* x86 vector goes in intrinfo[23:16] */
- ihandler |= intvec << 16;
- ipath_cdbg(VERBOSE, "ihandler lower %x, upper %x, intvec %x, "
- "interruptconfig %llx\n", int_handler_addr_lower,
- int_handler_addr_upper, intvec,
- (unsigned long long) ihandler);
-
- /* can't program yet, so save for interrupt setup */
- dd->ipath_intconfig = ihandler;
- /* keep going, so we find link control stuff also */
-
- return ihandler != 0;
+static int ipath_ht_intconfig(struct ipath_devdata *dd)
+{
+ int ret;
+
+ if (dd->ipath_intconfig) {
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_interruptconfig,
+ dd->ipath_intconfig); /* interrupt address */
+ ret = 0;
+ } else {
+ ipath_dev_err(dd, "No interrupts enabled, couldn't setup "
+ "interrupt address\n");
+ ret = -EINVAL;
+ }
+
+ return ret;
+}
+
+static void ipath_ht_irq_update(struct pci_dev *dev, int irq,
+ struct ht_irq_msg *msg)
+{
+ struct ipath_devdata *dd = pci_get_drvdata(dev);
+ u64 prev_intconfig = dd->ipath_intconfig;
+
+ dd->ipath_intconfig = msg->address_lo;
+ dd->ipath_intconfig |= ((u64) msg->address_hi) << 32;
+
+ /*
+ * If the previous value of dd->ipath_intconfig is zero, we're
+ * getting configured for the first time, and must not program the
+ * intconfig register here (it will be programmed later, when the
+ * hardware is ready). Otherwise, we should.
+ */
+ if (prev_intconfig)
+ ipath_ht_intconfig(dd);
}

/**
@@ -971,12 +963,19 @@ static int ipath_setup_ht_config(struct
static int ipath_setup_ht_config(struct ipath_devdata *dd,
struct pci_dev *pdev)
{
- int pos, ret = 0;
- int ihandler = 0;
-
- /*
- * Read the capability info to find the interrupt info, and also
- * handle clearing CRC errors in linkctrl register if necessary. We
+ int pos, ret;
+
+ ret = __ht_create_irq(pdev, 0, ipath_ht_irq_update);
+ if (ret < 0) {
+ ipath_dev_err(dd, "Couldn't create interrupt handler: "
+ "err %d\n", ret);
+ goto bail;
+ }
+ dd->ipath_irq = ret;
+ ret = 0;
+
+ /*
+ * Handle clearing CRC errors in linkctrl register if necessary. We
* do this early, before we ever enable errors or hardware errors,
* mostly to avoid causing the chip to enter freeze mode.
*/
@@ -1000,16 +999,8 @@ static int ipath_setup_ht_config(struct
}
if (!(cap_type & 0xE0))
slave_or_pri_blk(dd, pdev, pos, cap_type);
- else if (cap_type == HT_INTR_DISC_CONFIG)
- ihandler = set_int_handler(dd, pdev, pos);
} while ((pos = pci_find_next_capability(pdev, pos,
PCI_CAP_ID_HT)));
-
- if (!ihandler) {
- ipath_dev_err(dd, "Couldn't find interrupt handler in "
- "config space\n");
- ret = -ENODEV;
- }

bail:
return ret;
@@ -1360,25 +1351,6 @@ static void ipath_ht_quiet_serdes(struct
ipath_write_kreg(dd, dd->ipath_kregs->kr_serdesconfig0, val);
}

-static int ipath_ht_intconfig(struct ipath_devdata *dd)
-{
- int ret;
-
- if (!dd->ipath_intconfig) {
- ipath_dev_err(dd, "No interrupts enabled, couldn't setup "
- "interrupt address\n");
- ret = 1;
- goto bail;
- }
-
- ipath_write_kreg(dd, dd->ipath_kregs->kr_interruptconfig,
- dd->ipath_intconfig); /* interrupt address */
- ret = 0;
-
-bail:
- return ret;
-}
-
/**
* ipath_pe_put_tid - write a TID in chip
* @dd: the infinipath device
@@ -1575,6 +1547,14 @@ static int ipath_ht_get_base_info(struct
return 0;
}

+static void ipath_ht_free_irq(struct ipath_devdata *dd)
+{
+ free_irq(dd->ipath_irq, dd);
+ ht_destroy_irq(dd->ipath_irq);
+ dd->ipath_irq = 0;
+ dd->ipath_intconfig = 0;
+}
+
/**
* ipath_init_iba6110_funcs - set up the chip-specific function pointers
* @dd: the infinipath device
@@ -1598,6 +1578,7 @@ void ipath_init_iba6110_funcs(struct ipa
dd->ipath_f_cleanup = ipath_setup_ht_cleanup;
dd->ipath_f_setextled = ipath_setup_ht_setextled;
dd->ipath_f_get_base_info = ipath_ht_get_base_info;
+ dd->ipath_f_free_irq = ipath_ht_free_irq;

/*
* initialize chip-specific variables
diff -r 69779e2890e3 -r 545156d49f88 drivers/infiniband/hw/ipath/ipath_iba6120.c
--- a/drivers/infiniband/hw/ipath/ipath_iba6120.c Wed Nov 08 14:17:04 2006 -0800
+++ b/drivers/infiniband/hw/ipath/ipath_iba6120.c Wed Nov 08 14:19:27 2006 -0800
@@ -851,6 +851,7 @@ static int ipath_setup_pe_config(struct
int pos, ret;

dd->ipath_msi_lo = 0; /* used as a flag during reset processing */
+ dd->ipath_irq = pdev->irq;
ret = pci_enable_msi(dd->pcidev);
if (ret)
ipath_dev_err(dd, "pci_enable_msi failed: %d, "
@@ -1323,6 +1324,12 @@ done:
return 0;
}

+static void ipath_pe_free_irq(struct ipath_devdata *dd)
+{
+ free_irq(dd->ipath_irq, dd);
+ dd->ipath_irq = 0;
+}
+
/**
* ipath_init_iba6120_funcs - set up the chip-specific function pointers
* @dd: the infinipath device
@@ -1349,6 +1356,7 @@ void ipath_init_iba6120_funcs(struct ipa
dd->ipath_f_cleanup = ipath_setup_pe_cleanup;
dd->ipath_f_setextled = ipath_setup_pe_setextled;
dd->ipath_f_get_base_info = ipath_pe_get_base_info;
+ dd->ipath_f_free_irq = ipath_pe_free_irq;

/* initialize chip-specific variables */
dd->ipath_f_tidtemplate = ipath_pe_tidtemplate;
diff -r 69779e2890e3 -r 545156d49f88 drivers/infiniband/hw/ipath/ipath_intr.c
--- a/drivers/infiniband/hw/ipath/ipath_intr.c Wed Nov 08 14:17:04 2006 -0800
+++ b/drivers/infiniband/hw/ipath/ipath_intr.c Wed Nov 08 14:19:27 2006 -0800
@@ -710,14 +710,14 @@ static void ipath_bad_intr(struct ipath_
* linuxbios development work, and it may happen in
* the future again.
*/
- if (dd->pcidev && dd->pcidev->irq) {
+ if (dd->pcidev && dd->ipath_irq) {
ipath_dev_err(dd, "Now %u unexpected "
"interrupts, unregistering "
"interrupt handler\n",
*unexpectp);
- ipath_dbg("free_irq of irq %x\n",
- dd->pcidev->irq);
- free_irq(dd->pcidev->irq, dd);
+ ipath_dbg("free_irq of irq %d\n",
+ dd->ipath_irq);
+ dd->ipath_f_free_irq(dd);
}
}
if (ipath_read_kreg32(dd, dd->ipath_kregs->kr_intmask)) {
@@ -753,7 +753,7 @@ static void ipath_bad_regread(struct ipa
if (allbits == 2) {
ipath_dev_err(dd, "Still bad interrupt status, "
"unregistering interrupt\n");
- free_irq(dd->pcidev->irq, dd);
+ dd->ipath_f_free_irq(dd);
} else if (allbits > 2) {
if ((allbits % 10000) == 0)
printk(".");
diff -r 69779e2890e3 -r 545156d49f88 drivers/infiniband/hw/ipath/ipath_kernel.h
--- a/drivers/infiniband/hw/ipath/ipath_kernel.h Wed Nov 08 14:17:04 2006 -0800
+++ b/drivers/infiniband/hw/ipath/ipath_kernel.h Wed Nov 08 14:19:27 2006 -0800
@@ -213,6 +213,8 @@ struct ipath_devdata {
void (*ipath_f_setextled)(struct ipath_devdata *, u64, u64);
/* fill out chip-specific fields */
int (*ipath_f_get_base_info)(struct ipath_portdata *, void *);
+ /* free irq */
+ void (*ipath_f_free_irq)(struct ipath_devdata *);
struct ipath_ibdev *verbs_dev;
struct timer_list verbs_timer;
/* total dwords sent (summed from counter) */
@@ -328,6 +330,8 @@ struct ipath_devdata {
/* so we can rewrite it after a chip reset */
u32 ipath_pcibar1;

+ /* interrupt number */
+ int ipath_irq;
/* HT/PCI Vendor ID (here for NodeInfo) */
u16 ipath_vendorid;
/* HT/PCI Device ID (here for NodeInfo) */
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
\
 
 \ /
  Last update: 2006-11-08 23:25    [W:0.044 / U:0.512 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site