lkml.org 
[lkml]   [2006]   [Oct]   [3]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Subject[PATCH 5/6] Char: mxser_new, code upside down
From
Date
mxser_new, code upside down

Reorder functions upside down not to have too many prototypes of each
function and have some order (similar to other drivers).

Signed-off-by: Jiri Slaby <jirislaby@gmail.com>

---
commit b4f8f18a380e652a92f0dbd41622b5f536a00bed
tree cca50ad3262bc6e67efb643a820e4ca39fd3d961
parent 209164b6d9a593c402764e2735e9c3ff2d878835
author Jiri Slaby <jirislaby@gmail.com> Tue, 03 Oct 2006 23:57:51 +0200
committer Jiri Slaby <xslaby@anemoi.localdomain> Tue, 03 Oct 2006 23:57:51 +0200

drivers/char/mxser_new.c | 3045 ++++++++++++++++++++++------------------------
1 files changed, 1488 insertions(+), 1557 deletions(-)

diff --git a/drivers/char/mxser_new.c b/drivers/char/mxser_new.c
index 465314b..d4cb2d8 100644
--- a/drivers/char/mxser_new.c
+++ b/drivers/char/mxser_new.c
@@ -191,7 +191,6 @@ static const struct mxpciuart_info Gpci_
{MOXA_MUST_MU860_HWID, 128, 128, 128, 96, 96, 32, 921600L}
};

-
static struct pci_device_id mxser_pcibrds[] = {
{ PCI_DEVICE(PCI_VENDOR_ID_MOXA, PCI_DEVICE_ID_MOXA_C168),
.driver_data = MXSER_BOARD_C168_PCI },
@@ -377,57 +376,6 @@ static struct mxser_mon_ext mon_data_ext
static int mxser_set_baud_method[MXSER_PORTS + 1];
static spinlock_t gm_lock;

-/*
- * static functions:
- */
-
-static int mxser_init(void);
-
-/* static void mxser_poll(unsigned long); */
-static int mxser_get_ISA_conf(int, struct mxser_board *);
-static void mxser_do_softint(void *);
-static int mxser_open(struct tty_struct *, struct file *);
-static void mxser_close(struct tty_struct *, struct file *);
-static int mxser_write(struct tty_struct *, const unsigned char *, int);
-static int mxser_write_room(struct tty_struct *);
-static void mxser_flush_buffer(struct tty_struct *);
-static int mxser_chars_in_buffer(struct tty_struct *);
-static void mxser_flush_chars(struct tty_struct *);
-static void mxser_put_char(struct tty_struct *, unsigned char);
-static int mxser_ioctl(struct tty_struct *, struct file *, uint, ulong);
-static int mxser_ioctl_special(unsigned int, void __user *);
-static void mxser_throttle(struct tty_struct *);
-static void mxser_unthrottle(struct tty_struct *);
-static void mxser_set_termios(struct tty_struct *, struct termios *);
-static void mxser_stop(struct tty_struct *);
-static void mxser_start(struct tty_struct *);
-static void mxser_hangup(struct tty_struct *);
-static void mxser_rs_break(struct tty_struct *, int);
-static irqreturn_t mxser_interrupt(int, void *, struct pt_regs *);
-static void mxser_receive_chars(struct mxser_port *, int *);
-static void mxser_transmit_chars(struct mxser_port *);
-static void mxser_check_modem_status(struct mxser_port *, int);
-static int mxser_block_til_ready(struct tty_struct *, struct file *,
- struct mxser_port *);
-static int mxser_startup(struct mxser_port *);
-static void mxser_shutdown(struct mxser_port *);
-static int mxser_change_speed(struct mxser_port *, struct termios *);
-static int mxser_get_serial_info(struct mxser_port *,
- struct serial_struct __user *);
-static int mxser_set_serial_info(struct mxser_port *,
- struct serial_struct __user *);
-static int mxser_get_lsr_info(struct mxser_port *, unsigned int __user *);
-static void mxser_send_break(struct mxser_port *, int);
-static int mxser_tiocmget(struct tty_struct *, struct file *);
-static int mxser_tiocmset(struct tty_struct *, struct file *, unsigned int,
- unsigned int);
-static int mxser_set_baud(struct mxser_port *, long);
-static void mxser_wait_until_sent(struct tty_struct *, int);
-
-static void mxser_startrx(struct tty_struct *);
-static void mxser_stoprx(struct tty_struct *);
-
-
static int CheckIsMoxaMust(int io)
{
u8 oldmcr, hwid;
@@ -453,75 +401,6 @@ static int CheckIsMoxaMust(int io)

/* above is modified by Victor Yu. 08-15-2002 */

-static const struct tty_operations mxser_ops = {
- .open = mxser_open,
- .close = mxser_close,
- .write = mxser_write,
- .put_char = mxser_put_char,
- .flush_chars = mxser_flush_chars,
- .write_room = mxser_write_room,
- .chars_in_buffer = mxser_chars_in_buffer,
- .flush_buffer = mxser_flush_buffer,
- .ioctl = mxser_ioctl,
- .throttle = mxser_throttle,
- .unthrottle = mxser_unthrottle,
- .set_termios = mxser_set_termios,
- .stop = mxser_stop,
- .start = mxser_start,
- .hangup = mxser_hangup,
- .break_ctl = mxser_rs_break,
- .wait_until_sent = mxser_wait_until_sent,
- .tiocmget = mxser_tiocmget,
- .tiocmset = mxser_tiocmset,
-};
-
-/*
- * The MOXA Smartio/Industio serial driver boot-time initialization code!
- */
-
-static int __init mxser_module_init(void)
-{
- int ret;
-
- pr_debug("Loading module mxser ...\n");
- ret = mxser_init();
- pr_debug("Done.\n");
- return ret;
-}
-
-static void __exit mxser_module_exit(void)
-{
- int i, err;
-
- pr_debug("Unloading module mxser ...\n");
-
- err = tty_unregister_driver(mxvar_sdriver);
- if (!err)
- put_tty_driver(mxvar_sdriver);
- else
- printk(KERN_ERR "Couldn't unregister MOXA Smartio/Industio family serial driver\n");
-
- for (i = 0; i < MXSER_BOARDS; i++) {
- struct pci_dev *pdev;
-
- if (mxser_boards[i].board_type == -1)
- continue;
- else {
- pdev = mxser_boards[i].pdev;
- free_irq(mxser_boards[i].irq, &mxser_boards[i]);
- if (pdev != NULL) { /* PCI */
- pci_release_region(pdev, 2);
- pci_release_region(pdev, 3);
- pci_dev_put(pdev);
- } else {
- release_region(mxser_boards[i].ports[0].ioaddr, 8 * mxser_boards[i].nports);
- release_region(mxser_boards[i].vector, 1);
- }
- }
- }
- pr_debug("Done.\n");
-}
-
static void process_txrx_fifo(struct mxser_port *info)
{
int i;
@@ -542,349 +421,581 @@ static void process_txrx_fifo(struct mxs
}
}

-static int __devinit mxser_initbrd(struct mxser_board *brd)
+static void mxser_do_softint(void *private_)
{
- struct mxser_port *info;
- unsigned int i;
- int retval;
+ struct mxser_port *info = private_;
+ struct tty_struct *tty;

- printk(KERN_INFO "max. baud rate = %d bps.\n", brd->ports[0].max_baud);
+ tty = info->tty;

- for (i = 0; i < brd->nports; i++) {
- info = &brd->ports[i];
- info->board = brd;
- info->stop_rx = 0;
- info->ldisc_stop_rx = 0;
+ if (test_and_clear_bit(MXSER_EVENT_TXLOW, &info->event))
+ tty_wakeup(tty);
+ if (test_and_clear_bit(MXSER_EVENT_HANGUP, &info->event))
+ tty_hangup(tty);
+}

- /* Enhance mode enabled here */
- if (brd->chip_flag != MOXA_OTHER_UART)
- ENABLE_MOXA_MUST_ENCHANCE_MODE(info->ioaddr);
+static unsigned char mxser_get_msr(int baseaddr, int mode, int port)
+{
+ unsigned char status = 0;

- info->flags = ASYNC_SHARE_IRQ;
- info->type = brd->uart_type;
+ status = inb(baseaddr + UART_MSR);

- process_txrx_fifo(info);
+ mxser_msr[port] &= 0x0F;
+ mxser_msr[port] |= status;
+ status = mxser_msr[port];
+ if (mode)
+ mxser_msr[port] = 0;

- info->custom_divisor = info->baud_base * 16;
- info->close_delay = 5 * HZ / 10;
- info->closing_wait = 30 * HZ;
- INIT_WORK(&info->tqueue, mxser_do_softint, info);
- info->normal_termios = mxvar_sdriver->init_termios;
- init_waitqueue_head(&info->open_wait);
- init_waitqueue_head(&info->close_wait);
- init_waitqueue_head(&info->delta_msr_wait);
- memset(&info->mon_data, 0, sizeof(struct mxser_mon));
- info->err_shadow = 0;
- spin_lock_init(&info->slock);
+ return status;
+}

- /* before set INT ISR, disable all int */
- outb(inb(info->ioaddr + UART_IER) & 0xf0,
- info->ioaddr + UART_IER);
+static int mxser_block_til_ready(struct tty_struct *tty, struct file *filp,
+ struct mxser_port *port)
+{
+ DECLARE_WAITQUEUE(wait, current);
+ int retval;
+ int do_clocal = 0;
+ unsigned long flags;
+
+ /*
+ * If non-blocking mode is set, or the port is not enabled,
+ * then make the check up front and then exit.
+ */
+ if ((filp->f_flags & O_NONBLOCK) || (tty->flags & (1 << TTY_IO_ERROR))) {
+ port->flags |= ASYNC_NORMAL_ACTIVE;
+ return 0;
}
+
+ if (tty->termios->c_cflag & CLOCAL)
+ do_clocal = 1;
+
/*
- * Allocate the IRQ if necessary
+ * Block waiting for the carrier detect and the line to become
+ * free (i.e., not in use by the callout). While we are in
+ * this loop, port->count is dropped by one, so that
+ * mxser_close() knows when to free things. We restore it upon
+ * exit, either normal or abnormal.
*/
+ retval = 0;
+ add_wait_queue(&port->open_wait, &wait);

- retval = request_irq(brd->irq, mxser_interrupt,
- (brd->ports[0].flags & ASYNC_SHARE_IRQ) ? IRQF_SHARED :
- IRQF_DISABLED, "mxser", brd);
- if (retval) {
- printk(KERN_ERR "Board %s: Request irq failed, IRQ (%d) may "
- "conflict with another device.\n",
- mxser_brdname[brd->board_type - 1], brd->irq);
- return retval;
+ spin_lock_irqsave(&port->slock, flags);
+ if (!tty_hung_up_p(filp))
+ port->count--;
+ spin_unlock_irqrestore(&port->slock, flags);
+ port->blocked_open++;
+ while (1) {
+ spin_lock_irqsave(&port->slock, flags);
+ outb(inb(port->ioaddr + UART_MCR) |
+ UART_MCR_DTR | UART_MCR_RTS, port->ioaddr + UART_MCR);
+ spin_unlock_irqrestore(&port->slock, flags);
+ set_current_state(TASK_INTERRUPTIBLE);
+ if (tty_hung_up_p(filp) || !(port->flags & ASYNC_INITIALIZED)) {
+ if (port->flags & ASYNC_HUP_NOTIFY)
+ retval = -EAGAIN;
+ else
+ retval = -ERESTARTSYS;
+ break;
+ }
+ if (!(port->flags & ASYNC_CLOSING) &&
+ (do_clocal ||
+ (inb(port->ioaddr + UART_MSR) & UART_MSR_DCD)))
+ break;
+ if (signal_pending(current)) {
+ retval = -ERESTARTSYS;
+ break;
+ }
+ schedule();
}
+ set_current_state(TASK_RUNNING);
+ remove_wait_queue(&port->open_wait, &wait);
+ if (!tty_hung_up_p(filp))
+ port->count++;
+ port->blocked_open--;
+ if (retval)
+ return retval;
+ port->flags |= ASYNC_NORMAL_ACTIVE;
return 0;
}

-static int __init mxser_get_PCI_conf(int board_type, struct mxser_board *brd,
- struct pci_dev *pdev)
+static int mxser_set_baud(struct mxser_port *info, long newspd)
{
- unsigned int i, j;
- unsigned long ioaddress;
- int retval;
+ int quot = 0;
+ unsigned char cval;
+ int ret = 0;
+ unsigned long flags;

- /* io address */
- brd->board_type = board_type;
- brd->nports = mxser_numports[board_type - 1];
- ioaddress = pci_resource_start(pdev, 2);
- retval = pci_request_region(pdev, 2, "mxser(IO)");
- if (retval)
- goto err;
+ if (!info->tty || !info->tty->termios)
+ return ret;

- for (i = 0; i < brd->nports; i++)
- brd->ports[i].ioaddr = ioaddress + 8 * i;
+ if (!(info->ioaddr))
+ return ret;

- /* vector */
- ioaddress = pci_resource_start(pdev, 3);
- retval = pci_request_region(pdev, 3, "mxser(vector)");
- if (retval)
- goto err_relio;
- brd->vector = ioaddress;
+ if (newspd > info->max_baud)
+ return 0;

- /* irq */
- brd->irq = pdev->irq;
+ info->realbaud = newspd;
+ if (newspd == 134) {
+ quot = (2 * info->baud_base / 269);
+ } else if (newspd) {
+ quot = info->baud_base / newspd;
+ if (quot == 0)
+ quot = 1;
+ } else {
+ quot = 0;
+ }

- brd->chip_flag = CheckIsMoxaMust(brd->ports[0].ioaddr);
- brd->uart_type = PORT_16550A;
- brd->vector_mask = 0;
+ info->timeout = ((info->xmit_fifo_size * HZ * 10 * quot) / info->baud_base);
+ info->timeout += HZ / 50; /* Add .02 seconds of slop */

- for (i = 0; i < brd->nports; i++) {
- for (j = 0; j < UART_INFO_NUM; j++) {
- if (Gpci_uart_info[j].type == brd->chip_flag) {
- brd->ports[i].max_baud =
- Gpci_uart_info[j].max_baud;
+ if (quot) {
+ spin_lock_irqsave(&info->slock, flags);
+ info->MCR |= UART_MCR_DTR;
+ outb(info->MCR, info->ioaddr + UART_MCR);
+ spin_unlock_irqrestore(&info->slock, flags);
+ } else {
+ spin_lock_irqsave(&info->slock, flags);
+ info->MCR &= ~UART_MCR_DTR;
+ outb(info->MCR, info->ioaddr + UART_MCR);
+ spin_unlock_irqrestore(&info->slock, flags);
+ return ret;
+ }

- /* exception....CP-102 */
- if (board_type == MXSER_BOARD_CP102)
- brd->ports[i].max_baud = 921600;
+ cval = inb(info->ioaddr + UART_LCR);
+
+ outb(cval | UART_LCR_DLAB, info->ioaddr + UART_LCR); /* set DLAB */
+
+ outb(quot & 0xff, info->ioaddr + UART_DLL); /* LS of divisor */
+ outb(quot >> 8, info->ioaddr + UART_DLM); /* MS of divisor */
+ outb(cval, info->ioaddr + UART_LCR); /* reset DLAB */
+
+
+ return ret;
+}
+
+/*
+ * This routine is called to set the UART divisor registers to match
+ * the specified baud rate for a serial port.
+ */
+static int mxser_change_speed(struct mxser_port *info,
+ struct termios *old_termios)
+{
+ unsigned cflag, cval, fcr;
+ int ret = 0;
+ unsigned char status;
+ long baud;
+ unsigned long flags;
+
+ if (!info->tty || !info->tty->termios)
+ return ret;
+ cflag = info->tty->termios->c_cflag;
+ if (!(info->ioaddr))
+ return ret;
+
+#ifndef B921600
+#define B921600 (B460800 +1)
+#endif
+ if (mxser_set_baud_method[info->tty->index] == 0) {
+ baud = tty_get_baud_rate(info->tty);
+ mxser_set_baud(info, baud);
+ }
+
+ /* byte size and parity */
+ switch (cflag & CSIZE) {
+ case CS5:
+ cval = 0x00;
+ break;
+ case CS6:
+ cval = 0x01;
+ break;
+ case CS7:
+ cval = 0x02;
+ break;
+ case CS8:
+ cval = 0x03;
+ break;
+ default:
+ cval = 0x00;
+ break; /* too keep GCC shut... */
+ }
+ if (cflag & CSTOPB)
+ cval |= 0x04;
+ if (cflag & PARENB)
+ cval |= UART_LCR_PARITY;
+ if (!(cflag & PARODD))
+ cval |= UART_LCR_EPAR;
+ if (cflag & CMSPAR)
+ cval |= UART_LCR_SPAR;
+
+ if ((info->type == PORT_8250) || (info->type == PORT_16450)) {
+ if (info->board->chip_flag) {
+ fcr = UART_FCR_ENABLE_FIFO;
+ fcr |= MOXA_MUST_FCR_GDA_MODE_ENABLE;
+ SET_MOXA_MUST_FIFO_VALUE(info);
+ } else
+ fcr = 0;
+ } else {
+ fcr = UART_FCR_ENABLE_FIFO;
+ /* following add by Victor Yu. 08-30-2002 */
+ if (info->board->chip_flag) {
+ fcr |= MOXA_MUST_FCR_GDA_MODE_ENABLE;
+ SET_MOXA_MUST_FIFO_VALUE(info);
+ } else {
+ /* above add by Victor Yu. 08-30-2002 */
+ switch (info->rx_trigger) {
+ case 1:
+ fcr |= UART_FCR_TRIGGER_1;
+ break;
+ case 4:
+ fcr |= UART_FCR_TRIGGER_4;
+ break;
+ case 8:
+ fcr |= UART_FCR_TRIGGER_8;
+ break;
+ default:
+ fcr |= UART_FCR_TRIGGER_14;
break;
}
}
}

- if (brd->chip_flag == MOXA_MUST_MU860_HWID) {
- for (i = 0; i < brd->nports; i++) {
- if (i < 4)
- brd->ports[i].opmode_ioaddr = ioaddress + 4;
- else
- brd->ports[i].opmode_ioaddr = ioaddress + 0x0c;
+ /* CTS flow control flag and modem status interrupts */
+ info->IER &= ~UART_IER_MSI;
+ info->MCR &= ~UART_MCR_AFE;
+ if (cflag & CRTSCTS) {
+ info->flags |= ASYNC_CTS_FLOW;
+ info->IER |= UART_IER_MSI;
+ if ((info->type == PORT_16550A) || (info->board->chip_flag)) {
+ info->MCR |= UART_MCR_AFE;
+/* status = mxser_get_msr(info->ioaddr, 0, info->port); */
+/*
+ save_flags(flags);
+ cli();
+ status = inb(baseaddr + UART_MSR);
+ restore_flags(flags);
+*/
+ /* mxser_check_modem_status(info, status); */
+ } else {
+/* status = mxser_get_msr(info->ioaddr, 0, info->port); */
+ /* MX_LOCK(&info->slock); */
+ status = inb(info->ioaddr + UART_MSR);
+ /* MX_UNLOCK(&info->slock); */
+ if (info->tty->hw_stopped) {
+ if (status & UART_MSR_CTS) {
+ info->tty->hw_stopped = 0;
+ if (info->type != PORT_16550A &&
+ !info->board->chip_flag) {
+ outb(info->IER & ~UART_IER_THRI,
+ info->ioaddr +
+ UART_IER);
+ info->IER |= UART_IER_THRI;
+ outb(info->IER, info->ioaddr +
+ UART_IER);
+ }
+ set_bit(MXSER_EVENT_TXLOW, &info->event);
+ schedule_work(&info->tqueue); }
+ } else {
+ if (!(status & UART_MSR_CTS)) {
+ info->tty->hw_stopped = 1;
+ if ((info->type != PORT_16550A) &&
+ (!info->board->chip_flag)) {
+ info->IER &= ~UART_IER_THRI;
+ outb(info->IER, info->ioaddr +
+ UART_IER);
+ }
+ }
+ }
}
- outb(0, ioaddress + 4); /* default set to RS232 mode */
- outb(0, ioaddress + 0x0c); /* default set to RS232 mode */
+ } else {
+ info->flags &= ~ASYNC_CTS_FLOW;
}
-
- for (i = 0; i < brd->nports; i++) {
- brd->vector_mask |= (1 << i);
- brd->ports[i].baud_base = 921600;
+ outb(info->MCR, info->ioaddr + UART_MCR);
+ if (cflag & CLOCAL) {
+ info->flags &= ~ASYNC_CHECK_CD;
+ } else {
+ info->flags |= ASYNC_CHECK_CD;
+ info->IER |= UART_IER_MSI;
}
- return 0;
-err_relio:
- pci_release_region(pdev, 2);
-err:
- return retval;
-}
-
-static int __init mxser_init(void)
-{
- struct pci_dev *pdev = NULL;
- struct mxser_board *brd;
- unsigned int i, m;
- int retval, b, n;
-
- mxvar_sdriver = alloc_tty_driver(MXSER_PORTS + 1);
- if (!mxvar_sdriver)
- return -ENOMEM;
- spin_lock_init(&gm_lock);
+ outb(info->IER, info->ioaddr + UART_IER);

- for (i = 0; i < MXSER_BOARDS; i++)
- mxser_boards[i].board_type = -1;
+ /*
+ * Set up parity check flag
+ */
+ info->read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR;
+ if (I_INPCK(info->tty))
+ info->read_status_mask |= UART_LSR_FE | UART_LSR_PE;
+ if (I_BRKINT(info->tty) || I_PARMRK(info->tty))
+ info->read_status_mask |= UART_LSR_BI;

- printk(KERN_INFO "MOXA Smartio/Industio family driver version %s\n",
- MXSER_VERSION);
+ info->ignore_status_mask = 0;

- /* Initialize the tty_driver structure */
- mxvar_sdriver->magic = TTY_DRIVER_MAGIC;
- mxvar_sdriver->name = "ttyM";
- mxvar_sdriver->major = ttymajor;
- mxvar_sdriver->minor_start = 0;
- mxvar_sdriver->num = MXSER_PORTS + 1;
- mxvar_sdriver->type = TTY_DRIVER_TYPE_SERIAL;
- mxvar_sdriver->subtype = SERIAL_TYPE_NORMAL;
- mxvar_sdriver->init_termios = tty_std_termios;
- mxvar_sdriver->init_termios.c_cflag = B9600|CS8|CREAD|HUPCL|CLOCAL;
- mxvar_sdriver->flags = TTY_DRIVER_REAL_RAW;
- tty_set_operations(mxvar_sdriver, &mxser_ops);
- mxvar_sdriver->ttys = mxvar_tty;
- mxvar_sdriver->termios = mxvar_termios;
- mxvar_sdriver->termios_locked = mxvar_termios_locked;
+ if (I_IGNBRK(info->tty)) {
+ info->ignore_status_mask |= UART_LSR_BI;
+ info->read_status_mask |= UART_LSR_BI;
+ /*
+ * If we're ignore parity and break indicators, ignore
+ * overruns too. (For real raw support).
+ */
+ if (I_IGNPAR(info->tty)) {
+ info->ignore_status_mask |=
+ UART_LSR_OE |
+ UART_LSR_PE |
+ UART_LSR_FE;
+ info->read_status_mask |=
+ UART_LSR_OE |
+ UART_LSR_PE |
+ UART_LSR_FE;
+ }
+ }
+ /* following add by Victor Yu. 09-02-2002 */
+ if (info->board->chip_flag) {
+ spin_lock_irqsave(&info->slock, flags);
+ SET_MOXA_MUST_XON1_VALUE(info->ioaddr, START_CHAR(info->tty));
+ SET_MOXA_MUST_XOFF1_VALUE(info->ioaddr, STOP_CHAR(info->tty));
+ if (I_IXON(info->tty)) {
+ ENABLE_MOXA_MUST_RX_SOFTWARE_FLOW_CONTROL(info->ioaddr);
+ } else {
+ DISABLE_MOXA_MUST_RX_SOFTWARE_FLOW_CONTROL(info->ioaddr);
+ }
+ if (I_IXOFF(info->tty)) {
+ ENABLE_MOXA_MUST_TX_SOFTWARE_FLOW_CONTROL(info->ioaddr);
+ } else {
+ DISABLE_MOXA_MUST_TX_SOFTWARE_FLOW_CONTROL(info->ioaddr);
+ }
+ /*
+ if ( I_IXANY(info->tty) ) {
+ info->MCR |= MOXA_MUST_MCR_XON_ANY;
+ ENABLE_MOXA_MUST_XON_ANY_FLOW_CONTROL(info->ioaddr);
+ } else {
+ info->MCR &= ~MOXA_MUST_MCR_XON_ANY;
+ DISABLE_MOXA_MUST_XON_ANY_FLOW_CONTROL(info->ioaddr);
+ }
+ */
+ spin_unlock_irqrestore(&info->slock, flags);
+ }
+ /* above add by Victor Yu. 09-02-2002 */

- mxvar_diagflag = 0;

- m = 0;
- /* Start finding ISA boards here */
- for (b = 0; b < MXSER_BOARDS && m < MXSER_BOARDS; b++) {
- int cap;
+ outb(fcr, info->ioaddr + UART_FCR); /* set fcr */
+ outb(cval, info->ioaddr + UART_LCR);

- if (!(cap = mxserBoardCAP[b]))
- continue;
+ return ret;
+}

- brd = &mxser_boards[m];
- retval = mxser_get_ISA_conf(cap, brd);
+static void mxser_check_modem_status(struct mxser_port *port, int status)
+{
+ /* update input line counters */
+ if (status & UART_MSR_TERI)
+ port->icount.rng++;
+ if (status & UART_MSR_DDSR)
+ port->icount.dsr++;
+ if (status & UART_MSR_DDCD)
+ port->icount.dcd++;
+ if (status & UART_MSR_DCTS)
+ port->icount.cts++;
+ port->mon_data.modem_status = status;
+ wake_up_interruptible(&port->delta_msr_wait);

- if (retval != 0)
- printk(KERN_INFO "Found MOXA %s board (CAP=0x%x)\n",
- mxser_brdname[brd->board_type - 1], ioaddr[b]);
+ if ((port->flags & ASYNC_CHECK_CD) && (status & UART_MSR_DDCD)) {
+ if (status & UART_MSR_DCD)
+ wake_up_interruptible(&port->open_wait);
+ schedule_work(&port->tqueue);
+ }

- if (retval <= 0) {
- if (retval == MXSER_ERR_IRQ)
- printk(KERN_ERR "Invalid interrupt number, "
- "board not configured\n");
- else if (retval == MXSER_ERR_IRQ_CONFLIT)
- printk(KERN_ERR "Invalid interrupt number, "
- "board not configured\n");
- else if (retval == MXSER_ERR_VECTOR)
- printk(KERN_ERR "Invalid interrupt vector, "
- "board not configured\n");
- else if (retval == MXSER_ERR_IOADDR)
- printk(KERN_ERR "Invalid I/O address, "
- "board not configured\n");
+ if (port->flags & ASYNC_CTS_FLOW) {
+ if (port->tty->hw_stopped) {
+ if (status & UART_MSR_CTS) {
+ port->tty->hw_stopped = 0;

- continue;
+ if ((port->type != PORT_16550A) &&
+ (!port->board->chip_flag)) {
+ outb(port->IER & ~UART_IER_THRI,
+ port->ioaddr + UART_IER);
+ port->IER |= UART_IER_THRI;
+ outb(port->IER, port->ioaddr +
+ UART_IER);
+ }
+ set_bit(MXSER_EVENT_TXLOW, &port->event);
+ schedule_work(&port->tqueue);
+ }
+ } else {
+ if (!(status & UART_MSR_CTS)) {
+ port->tty->hw_stopped = 1;
+ if (port->type != PORT_16550A &&
+ !port->board->chip_flag) {
+ port->IER &= ~UART_IER_THRI;
+ outb(port->IER, port->ioaddr +
+ UART_IER);
+ }
+ }
}
+ }
+}

- brd->pdev = NULL;
+static int mxser_startup(struct mxser_port *info)
+{
+ unsigned long page;
+ unsigned long flags;

- /* mxser_initbrd will hook ISR. */
- if (mxser_initbrd(brd) < 0)
- continue;
+ page = __get_free_page(GFP_KERNEL);
+ if (!page)
+ return -ENOMEM;

- m++;
- }
+ spin_lock_irqsave(&info->slock, flags);

- /* Start finding ISA boards from module arg */
- for (b = 0; b < MXSER_BOARDS && m < MXSER_BOARDS; b++) {
- unsigned long cap;
+ if (info->flags & ASYNC_INITIALIZED) {
+ free_page(page);
+ spin_unlock_irqrestore(&info->slock, flags);
+ return 0;
+ }

- if (!(cap = ioaddr[b]))
- continue;
+ if (!info->ioaddr || !info->type) {
+ if (info->tty)
+ set_bit(TTY_IO_ERROR, &info->tty->flags);
+ free_page(page);
+ spin_unlock_irqrestore(&info->slock, flags);
+ return 0;
+ }
+ if (info->xmit_buf)
+ free_page(page);
+ else
+ info->xmit_buf = (unsigned char *) page;

- brd = &mxser_boards[m];
- retval = mxser_get_ISA_conf(cap, &mxser_boards[m]);
+ /*
+ * Clear the FIFO buffers and disable them
+ * (they will be reenabled in mxser_change_speed())
+ */
+ if (info->board->chip_flag)
+ outb((UART_FCR_CLEAR_RCVR |
+ UART_FCR_CLEAR_XMIT |
+ MOXA_MUST_FCR_GDA_MODE_ENABLE), info->ioaddr + UART_FCR);
+ else
+ outb((UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT),
+ info->ioaddr + UART_FCR);

- if (retval != 0)
- printk(KERN_INFO "Found MOXA %s board (CAP=0x%x)\n",
- mxser_brdname[brd->board_type - 1], ioaddr[b]);
+ /*
+ * At this point there's no way the LSR could still be 0xFF;
+ * if it is, then bail out, because there's likely no UART
+ * here.
+ */
+ if (inb(info->ioaddr + UART_LSR) == 0xff) {
+ spin_unlock_irqrestore(&info->slock, flags);
+ if (capable(CAP_SYS_ADMIN)) {
+ if (info->tty)
+ set_bit(TTY_IO_ERROR, &info->tty->flags);
+ return 0;
+ } else
+ return -ENODEV;
+ }

- if (retval <= 0) {
- if (retval == MXSER_ERR_IRQ)
- printk(KERN_ERR "Invalid interrupt number, "
- "board not configured\n");
- else if (retval == MXSER_ERR_IRQ_CONFLIT)
- printk(KERN_ERR "Invalid interrupt number, "
- "board not configured\n");
- else if (retval == MXSER_ERR_VECTOR)
- printk(KERN_ERR "Invalid interrupt vector, "
- "board not configured\n");
- else if (retval == MXSER_ERR_IOADDR)
- printk(KERN_ERR "Invalid I/O address, "
- "board not configured\n");
+ /*
+ * Clear the interrupt registers.
+ */
+ (void) inb(info->ioaddr + UART_LSR);
+ (void) inb(info->ioaddr + UART_RX);
+ (void) inb(info->ioaddr + UART_IIR);
+ (void) inb(info->ioaddr + UART_MSR);

- continue;
- }
+ /*
+ * Now, initialize the UART
+ */
+ outb(UART_LCR_WLEN8, info->ioaddr + UART_LCR); /* reset DLAB */
+ info->MCR = UART_MCR_DTR | UART_MCR_RTS;
+ outb(info->MCR, info->ioaddr + UART_MCR);

- brd->pdev = NULL;
- /* mxser_initbrd will hook ISR. */
- if (mxser_initbrd(brd) < 0)
- continue;
+ /*
+ * Finally, enable interrupts
+ */
+ info->IER = UART_IER_MSI | UART_IER_RLSI | UART_IER_RDI;
+ /* info->IER = UART_IER_RLSI | UART_IER_RDI; */

- m++;
- }
+ /* following add by Victor Yu. 08-30-2002 */
+ if (info->board->chip_flag)
+ info->IER |= MOXA_MUST_IER_EGDAI;
+ /* above add by Victor Yu. 08-30-2002 */
+ outb(info->IER, info->ioaddr + UART_IER); /* enable interrupts */

- /* start finding PCI board here */
- n = ARRAY_SIZE(mxser_pcibrds) - 1;
- b = 0;
- while (b < n) {
- pdev = pci_get_device(mxser_pcibrds[b].vendor,
- mxser_pcibrds[b].device, pdev);
- if (pdev == NULL) {
- b++;
- continue;
- }
- printk(KERN_INFO "Found MOXA %s board(BusNo=%d,DevNo=%d)\n",
- mxser_brdname[(int) (mxser_pcibrds[b].driver_data) - 1],
- pdev->bus->number, PCI_SLOT(pdev->devfn));
- if (m >= MXSER_BOARDS)
- printk(KERN_ERR
- "Too many Smartio/Industio family boards find "
- "(maximum %d), board not configured\n",
- MXSER_BOARDS);
- else {
- if (pci_enable_device(pdev)) {
- printk(KERN_ERR "Moxa SmartI/O PCI enable "
- "fail !\n");
- continue;
- }
- brd = &mxser_boards[m];
- brd->pdev = pdev;
- retval = mxser_get_PCI_conf(
- (int)mxser_pcibrds[b].driver_data,
- brd, pdev);
- if (retval < 0) {
- if (retval == MXSER_ERR_IRQ)
- printk(KERN_ERR
- "Invalid interrupt number, "
- "board not configured\n");
- else if (retval == MXSER_ERR_IRQ_CONFLIT)
- printk(KERN_ERR
- "Invalid interrupt number, "
- "board not configured\n");
- else if (retval == MXSER_ERR_VECTOR)
- printk(KERN_ERR
- "Invalid interrupt vector, "
- "board not configured\n");
- else if (retval == MXSER_ERR_IOADDR)
- printk(KERN_ERR
- "Invalid I/O address, "
- "board not configured\n");
- continue;
- }
- /* mxser_initbrd will hook ISR. */
- if (mxser_initbrd(brd) < 0)
- continue;
- m++;
- /* Keep an extra reference if we succeeded. It will
- be returned at unload time */
- pci_dev_get(pdev);
- }
- }
+ /*
+ * And clear the interrupt registers again for luck.
+ */
+ (void) inb(info->ioaddr + UART_LSR);
+ (void) inb(info->ioaddr + UART_RX);
+ (void) inb(info->ioaddr + UART_IIR);
+ (void) inb(info->ioaddr + UART_MSR);

- retval = tty_register_driver(mxvar_sdriver);
- if (retval) {
- printk(KERN_ERR "Couldn't install MOXA Smartio/Industio family"
- " driver !\n");
- put_tty_driver(mxvar_sdriver);
+ if (info->tty)
+ clear_bit(TTY_IO_ERROR, &info->tty->flags);
+ info->xmit_cnt = info->xmit_head = info->xmit_tail = 0;

- for (i = 0; i < MXSER_BOARDS; i++) {
- if (mxser_boards[i].board_type == -1)
- continue;
- else {
- free_irq(mxser_boards[i].irq, &mxser_boards[i]);
- /* todo: release io, vector */
- }
- }
- return retval;
- }
+ /*
+ * and set the speed of the serial port
+ */
+ spin_unlock_irqrestore(&info->slock, flags);
+ mxser_change_speed(info, NULL);

+ info->flags |= ASYNC_INITIALIZED;
return 0;
}

-static void mxser_do_softint(void *private_)
+/*
+ * This routine will shutdown a serial port; interrupts maybe disabled, and
+ * DTR is dropped if the hangup on close termio flag is on.
+ */
+static void mxser_shutdown(struct mxser_port *info)
{
- struct mxser_port *info = private_;
- struct tty_struct *tty;
+ unsigned long flags;

- tty = info->tty;
+ if (!(info->flags & ASYNC_INITIALIZED))
+ return;

- if (test_and_clear_bit(MXSER_EVENT_TXLOW, &info->event))
- tty_wakeup(tty);
- if (test_and_clear_bit(MXSER_EVENT_HANGUP, &info->event))
- tty_hangup(tty);
-}
+ spin_lock_irqsave(&info->slock, flags);

-static unsigned char mxser_get_msr(int baseaddr, int mode, int port)
-{
- unsigned char status = 0;
+ /*
+ * clear delta_msr_wait queue to avoid mem leaks: we may free the irq
+ * here so the queue might never be waken up
+ */
+ wake_up_interruptible(&info->delta_msr_wait);

- status = inb(baseaddr + UART_MSR);
+ /*
+ * Free the IRQ, if necessary
+ */
+ if (info->xmit_buf) {
+ free_page((unsigned long) info->xmit_buf);
+ info->xmit_buf = NULL;
+ }

- mxser_msr[port] &= 0x0F;
- mxser_msr[port] |= status;
- status = mxser_msr[port];
- if (mode)
- mxser_msr[port] = 0;
+ info->IER = 0;
+ outb(0x00, info->ioaddr + UART_IER);

- return status;
+ if (!info->tty || (info->tty->termios->c_cflag & HUPCL))
+ info->MCR &= ~(UART_MCR_DTR | UART_MCR_RTS);
+ outb(info->MCR, info->ioaddr + UART_MCR);
+
+ /* clear Rx/Tx FIFO's */
+ /* following add by Victor Yu. 08-30-2002 */
+ if (info->board->chip_flag)
+ outb(UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT |
+ MOXA_MUST_FCR_GDA_MODE_ENABLE,
+ info->ioaddr + UART_FCR);
+ else
+ /* above add by Victor Yu. 08-30-2002 */
+ outb(UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT,
+ info->ioaddr + UART_FCR);
+
+ /* read data port to reset things */
+ (void) inb(info->ioaddr + UART_RX);
+
+ if (info->tty)
+ set_bit(TTY_IO_ERROR, &info->tty->flags);
+
+ info->flags &= ~ASYNC_INITIALIZED;
+
+ /* following add by Victor Yu. 09-23-2002 */
+ if (info->board->chip_flag)
+ SET_MOXA_MUST_NO_SOFTWARE_FLOW_CONTROL(info->ioaddr);
+ /* above add by Victor Yu. 09-23-2002 */
+
+ spin_unlock_irqrestore(&info->slock, flags);
}

/*
@@ -1200,250 +1311,295 @@ static void mxser_flush_buffer(struct tt
(tty->ldisc.write_wakeup) (tty);
}

-static int mxser_ioctl(struct tty_struct *tty, struct file *file, unsigned int cmd, unsigned long arg)
+/*
+ * ------------------------------------------------------------
+ * friends of mxser_ioctl()
+ * ------------------------------------------------------------
+ */
+static int mxser_get_serial_info(struct mxser_port *info,
+ struct serial_struct __user *retinfo)
{
- struct mxser_port *info = tty->driver_data;
- int retval;
- struct async_icount cprev, cnow; /* kernel counter temps */
- struct serial_icounter_struct __user *p_cuser;
- unsigned long templ;
- unsigned long flags;
- void __user *argp = (void __user *)arg;
+ struct serial_struct tmp;

- if (tty->index == MXSER_PORTS)
- return mxser_ioctl_special(cmd, argp);
+ if (!retinfo)
+ return -EFAULT;
+ memset(&tmp, 0, sizeof(tmp));
+ tmp.type = info->type;
+ tmp.line = info->tty->index;
+ tmp.port = info->ioaddr;
+ tmp.irq = info->board->irq;
+ tmp.flags = info->flags;
+ tmp.baud_base = info->baud_base;
+ tmp.close_delay = info->close_delay;
+ tmp.closing_wait = info->closing_wait;
+ tmp.custom_divisor = info->custom_divisor;
+ tmp.hub6 = 0;
+ if (copy_to_user(retinfo, &tmp, sizeof(*retinfo)))
+ return -EFAULT;
+ return 0;
+}

- /* following add by Victor Yu. 01-05-2004 */
- if (cmd == MOXA_SET_OP_MODE || cmd == MOXA_GET_OP_MODE) {
- int p;
- unsigned long opmode;
- static unsigned char ModeMask[] = { 0xfc, 0xf3, 0xcf, 0x3f };
- int shiftbit;
- unsigned char val, mask;
+static int mxser_set_serial_info(struct mxser_port *info,
+ struct serial_struct __user *new_info)
+{
+ struct serial_struct new_serial;
+ unsigned int flags;
+ int retval = 0;

- p = tty->index % 4;
- if (cmd == MOXA_SET_OP_MODE) {
- if (get_user(opmode, (int __user *) argp))
- return -EFAULT;
- if (opmode != RS232_MODE &&
- opmode != RS485_2WIRE_MODE &&
- opmode != RS422_MODE &&
- opmode != RS485_4WIRE_MODE)
- return -EFAULT;
- mask = ModeMask[p];
- shiftbit = p * 2;
- val = inb(info->opmode_ioaddr);
- val &= mask;
- val |= (opmode << shiftbit);
- outb(val, info->opmode_ioaddr);
- } else {
- shiftbit = p * 2;
- opmode = inb(info->opmode_ioaddr) >> shiftbit;
- opmode &= OP_MODE_MASK;
- if (copy_to_user(argp, &opmode, sizeof(int)))
- return -EFAULT;
- }
- return 0;
- }
- /* above add by Victor Yu. 01-05-2004 */
+ if (!new_info || !info->ioaddr)
+ return -EFAULT;
+ if (copy_from_user(&new_serial, new_info, sizeof(new_serial)))
+ return -EFAULT;

- if ((cmd != TIOCGSERIAL) && (cmd != TIOCMIWAIT) && (cmd != TIOCGICOUNT)) {
- if (tty->flags & (1 << TTY_IO_ERROR))
- return -EIO;
- }
- switch (cmd) {
- case TCSBRK: /* SVID version: non-zero arg --> no break */
- retval = tty_check_change(tty);
- if (retval)
- return retval;
- tty_wait_until_sent(tty, 0);
- if (!arg)
- mxser_send_break(info, HZ / 4); /* 1/4 second */
- return 0;
- case TCSBRKP: /* support for POSIX tcsendbreak() */
- retval = tty_check_change(tty);
- if (retval)
- return retval;
- tty_wait_until_sent(tty, 0);
- mxser_send_break(info, arg ? arg * (HZ / 10) : HZ / 4);
- return 0;
- case TIOCGSOFTCAR:
- return put_user(C_CLOCAL(tty) ? 1 : 0, (unsigned long __user *)argp);
- case TIOCSSOFTCAR:
- if (get_user(templ, (unsigned long __user *) argp))
- return -EFAULT;
- arg = templ;
- tty->termios->c_cflag = ((tty->termios->c_cflag & ~CLOCAL) | (arg ? CLOCAL : 0));
- return 0;
- case TIOCGSERIAL:
- return mxser_get_serial_info(info, argp);
- case TIOCSSERIAL:
- return mxser_set_serial_info(info, argp);
- case TIOCSERGETLSR: /* Get line status register */
- return mxser_get_lsr_info(info, argp);
- /*
- * Wait for any of the 4 modem inputs (DCD,RI,DSR,CTS) to change
- * - mask passed in arg for lines of interest
- * (use |'ed TIOCM_RNG/DSR/CD/CTS for masking)
- * Caller should use TIOCGICOUNT to see which one it was
- */
- case TIOCMIWAIT: {
- DECLARE_WAITQUEUE(wait, current);
- int ret;
- spin_lock_irqsave(&info->slock, flags);
- cprev = info->icount; /* note the counters on entry */
- spin_unlock_irqrestore(&info->slock, flags);
+ if ((new_serial.irq != info->board->irq) ||
+ (new_serial.port != info->ioaddr) ||
+ (new_serial.custom_divisor != info->custom_divisor) ||
+ (new_serial.baud_base != info->baud_base))
+ return -EPERM;

- add_wait_queue(&info->delta_msr_wait, &wait);
- while (1) {
- spin_lock_irqsave(&info->slock, flags);
- cnow = info->icount; /* atomic copy */
- spin_unlock_irqrestore(&info->slock, flags);
-
- set_current_state(TASK_INTERRUPTIBLE);
- if (((arg & TIOCM_RNG) &&
- (cnow.rng != cprev.rng)) ||
- ((arg & TIOCM_DSR) &&
- (cnow.dsr != cprev.dsr)) ||
- ((arg & TIOCM_CD) &&
- (cnow.dcd != cprev.dcd)) ||
- ((arg & TIOCM_CTS) &&
- (cnow.cts != cprev.cts))) {
- ret = 0;
- break;
- }
- /* see if a signal did it */
- if (signal_pending(current)) {
- ret = -ERESTARTSYS;
- break;
- }
- cprev = cnow;
- }
- current->state = TASK_RUNNING;
- remove_wait_queue(&info->delta_msr_wait, &wait);
- break;
- }
- /* NOTREACHED */
+ flags = info->flags & ASYNC_SPD_MASK;
+
+ if (!capable(CAP_SYS_ADMIN)) {
+ if ((new_serial.baud_base != info->baud_base) ||
+ (new_serial.close_delay != info->close_delay) ||
+ ((new_serial.flags & ~ASYNC_USR_MASK) != (info->flags & ~ASYNC_USR_MASK)))
+ return -EPERM;
+ info->flags = ((info->flags & ~ASYNC_USR_MASK) |
+ (new_serial.flags & ASYNC_USR_MASK));
+ } else {
/*
- * Get counter of input serial line interrupts (DCD,RI,DSR,CTS)
- * Return: write counters to the user passed counter struct
- * NB: both 1->0 and 0->1 transitions are counted except for
- * RI where only 0->1 is counted.
+ * OK, past this point, all the error checking has been done.
+ * At this point, we start making changes.....
*/
- case TIOCGICOUNT:
- spin_lock_irqsave(&info->slock, flags);
- cnow = info->icount;
- spin_unlock_irqrestore(&info->slock, flags);
- p_cuser = argp;
- /* modified by casper 1/11/2000 */
- if (put_user(cnow.frame, &p_cuser->frame))
- return -EFAULT;
- if (put_user(cnow.brk, &p_cuser->brk))
- return -EFAULT;
- if (put_user(cnow.overrun, &p_cuser->overrun))
- return -EFAULT;
- if (put_user(cnow.buf_overrun, &p_cuser->buf_overrun))
- return -EFAULT;
- if (put_user(cnow.parity, &p_cuser->parity))
- return -EFAULT;
- if (put_user(cnow.rx, &p_cuser->rx))
- return -EFAULT;
- if (put_user(cnow.tx, &p_cuser->tx))
- return -EFAULT;
- put_user(cnow.cts, &p_cuser->cts);
- put_user(cnow.dsr, &p_cuser->dsr);
- put_user(cnow.rng, &p_cuser->rng);
- put_user(cnow.dcd, &p_cuser->dcd);
- return 0;
- case MOXA_HighSpeedOn:
- return put_user(info->baud_base != 115200 ? 1 : 0, (int __user *)argp);
- case MOXA_SDS_RSTICOUNTER: {
- info->mon_data.rxcnt = 0;
- info->mon_data.txcnt = 0;
- return 0;
- }
-/* (above) added by James. */
- case MOXA_ASPP_SETBAUD:{
- long baud;
- if (get_user(baud, (long __user *)argp))
- return -EFAULT;
- mxser_set_baud(info, baud);
- return 0;
- }
- case MOXA_ASPP_GETBAUD:
- if (copy_to_user(argp, &info->realbaud, sizeof(long)))
- return -EFAULT;
+ info->flags = ((info->flags & ~ASYNC_FLAGS) |
+ (new_serial.flags & ASYNC_FLAGS));
+ info->close_delay = new_serial.close_delay * HZ / 100;
+ info->closing_wait = new_serial.closing_wait * HZ / 100;
+ info->tty->low_latency =
+ (info->flags & ASYNC_LOW_LATENCY) ? 1 : 0;
+ info->tty->low_latency = 0; /* (info->flags & ASYNC_LOW_LATENCY) ? 1 : 0; */
+ }

- return 0;
+ /* added by casper, 3/17/2000, for mouse */
+ info->type = new_serial.type;

- case MOXA_ASPP_OQUEUE:{
- int len, lsr;
+ process_txrx_fifo(info);

- len = mxser_chars_in_buffer(tty);
+ if (info->flags & ASYNC_INITIALIZED) {
+ if (flags != (info->flags & ASYNC_SPD_MASK))
+ mxser_change_speed(info, NULL);
+ } else
+ retval = mxser_startup(info);

- lsr = inb(info->ioaddr + UART_LSR) & UART_LSR_TEMT;
+ return retval;
+}

- len += (lsr ? 0 : 1);
+/*
+ * mxser_get_lsr_info - get line status register info
+ *
+ * Purpose: Let user call ioctl() to get info when the UART physically
+ * is emptied. On bus types like RS485, the transmitter must
+ * release the bus after transmitting. This must be done when
+ * the transmit shift register is empty, not be done when the
+ * transmit holding register is empty. This functionality
+ * allows an RS485 driver to be written in user space.
+ */
+static int mxser_get_lsr_info(struct mxser_port *info,
+ unsigned int __user *value)
+{
+ unsigned char status;
+ unsigned int result;
+ unsigned long flags;

- if (copy_to_user(argp, &len, sizeof(int)))
- return -EFAULT;
+ spin_lock_irqsave(&info->slock, flags);
+ status = inb(info->ioaddr + UART_LSR);
+ spin_unlock_irqrestore(&info->slock, flags);
+ result = ((status & UART_LSR_TEMT) ? TIOCSER_TEMT : 0);
+ return put_user(result, value);
+}

- return 0;
- }
- case MOXA_ASPP_MON: {
- int mcr, status;
+/*
+ * This routine sends a break character out the serial port.
+ */
+static void mxser_send_break(struct mxser_port *info, int duration)
+{
+ unsigned long flags;

- /* info->mon_data.ser_param = tty->termios->c_cflag; */
+ if (!info->ioaddr)
+ return;
+ set_current_state(TASK_INTERRUPTIBLE);
+ spin_lock_irqsave(&info->slock, flags);
+ outb(inb(info->ioaddr + UART_LCR) | UART_LCR_SBC,
+ info->ioaddr + UART_LCR);
+ spin_unlock_irqrestore(&info->slock, flags);
+ schedule_timeout(duration);
+ spin_lock_irqsave(&info->slock, flags);
+ outb(inb(info->ioaddr + UART_LCR) & ~UART_LCR_SBC,
+ info->ioaddr + UART_LCR);
+ spin_unlock_irqrestore(&info->slock, flags);
+}

- status = mxser_get_msr(info->ioaddr, 1, tty->index);
- mxser_check_modem_status(info, status);
+static int mxser_tiocmget(struct tty_struct *tty, struct file *file)
+{
+ struct mxser_port *info = tty->driver_data;
+ unsigned char control, status;
+ unsigned long flags;

- mcr = inb(info->ioaddr + UART_MCR);
- if (mcr & MOXA_MUST_MCR_XON_FLAG)
- info->mon_data.hold_reason &= ~NPPI_NOTIFY_XOFFHOLD;
- else
- info->mon_data.hold_reason |= NPPI_NOTIFY_XOFFHOLD;

- if (mcr & MOXA_MUST_MCR_TX_XON)
- info->mon_data.hold_reason &= ~NPPI_NOTIFY_XOFFXENT;
- else
- info->mon_data.hold_reason |= NPPI_NOTIFY_XOFFXENT;
+ if (tty->index == MXSER_PORTS)
+ return -ENOIOCTLCMD;
+ if (tty->flags & (1 << TTY_IO_ERROR))
+ return -EIO;

- if (info->tty->hw_stopped)
- info->mon_data.hold_reason |= NPPI_NOTIFY_CTSHOLD;
- else
- info->mon_data.hold_reason &= ~NPPI_NOTIFY_CTSHOLD;
+ control = info->MCR;

- if (copy_to_user(argp, &info->mon_data,
- sizeof(struct mxser_mon)))
- return -EFAULT;
+ spin_lock_irqsave(&info->slock, flags);
+ status = inb(info->ioaddr + UART_MSR);
+ if (status & UART_MSR_ANY_DELTA)
+ mxser_check_modem_status(info, status);
+ spin_unlock_irqrestore(&info->slock, flags);
+ return ((control & UART_MCR_RTS) ? TIOCM_RTS : 0) |
+ ((control & UART_MCR_DTR) ? TIOCM_DTR : 0) |
+ ((status & UART_MSR_DCD) ? TIOCM_CAR : 0) |
+ ((status & UART_MSR_RI) ? TIOCM_RNG : 0) |
+ ((status & UART_MSR_DSR) ? TIOCM_DSR : 0) |
+ ((status & UART_MSR_CTS) ? TIOCM_CTS : 0);
+}

- return 0;
- }
+static int mxser_tiocmset(struct tty_struct *tty, struct file *file,
+ unsigned int set, unsigned int clear)
+{
+ struct mxser_port *info = tty->driver_data;
+ unsigned long flags;

- case MOXA_ASPP_LSTATUS: {
- if (copy_to_user(argp, &info->err_shadow,
- sizeof(unsigned char)))
- return -EFAULT;

- info->err_shadow = 0;
- return 0;
- }
- case MOXA_SET_BAUD_METHOD: {
- int method;
+ if (tty->index == MXSER_PORTS)
+ return -ENOIOCTLCMD;
+ if (tty->flags & (1 << TTY_IO_ERROR))
+ return -EIO;

- if (get_user(method, (int __user *)argp))
- return -EFAULT;
- mxser_set_baud_method[tty->index] = method;
- if (copy_to_user(argp, &method, sizeof(int)))
- return -EFAULT;
+ spin_lock_irqsave(&info->slock, flags);

- return 0;
+ if (set & TIOCM_RTS)
+ info->MCR |= UART_MCR_RTS;
+ if (set & TIOCM_DTR)
+ info->MCR |= UART_MCR_DTR;
+
+ if (clear & TIOCM_RTS)
+ info->MCR &= ~UART_MCR_RTS;
+ if (clear & TIOCM_DTR)
+ info->MCR &= ~UART_MCR_DTR;
+
+ outb(info->MCR, info->ioaddr + UART_MCR);
+ spin_unlock_irqrestore(&info->slock, flags);
+ return 0;
+}
+
+static int mxser_program_mode(int port)
+{
+ int id, i, j, n;
+ /* unsigned long flags; */
+
+ spin_lock(&gm_lock);
+ outb(0, port);
+ outb(0, port);
+ outb(0, port);
+ (void)inb(port);
+ (void)inb(port);
+ outb(0, port);
+ (void)inb(port);
+ /* restore_flags(flags); */
+ spin_unlock(&gm_lock);
+
+ id = inb(port + 1) & 0x1F;
+ if ((id != C168_ASIC_ID) &&
+ (id != C104_ASIC_ID) &&
+ (id != C102_ASIC_ID) &&
+ (id != CI132_ASIC_ID) &&
+ (id != CI134_ASIC_ID) &&
+ (id != CI104J_ASIC_ID))
+ return -1;
+ for (i = 0, j = 0; i < 4; i++) {
+ n = inb(port + 2);
+ if (n == 'M') {
+ j = 1;
+ } else if ((j == 1) && (n == 1)) {
+ j = 2;
+ break;
+ } else
+ j = 0;
+ }
+ if (j != 2)
+ id = -2;
+ return id;
+}
+
+static void mxser_normal_mode(int port)
+{
+ int i, n;
+
+ outb(0xA5, port + 1);
+ outb(0x80, port + 3);
+ outb(12, port + 0); /* 9600 bps */
+ outb(0, port + 1);
+ outb(0x03, port + 3); /* 8 data bits */
+ outb(0x13, port + 4); /* loop back mode */
+ for (i = 0; i < 16; i++) {
+ n = inb(port + 5);
+ if ((n & 0x61) == 0x60)
+ break;
+ if ((n & 1) == 1)
+ (void)inb(port);
+ }
+ outb(0x00, port + 4);
+}
+
+#define CHIP_SK 0x01 /* Serial Data Clock in Eprom */
+#define CHIP_DO 0x02 /* Serial Data Output in Eprom */
+#define CHIP_CS 0x04 /* Serial Chip Select in Eprom */
+#define CHIP_DI 0x08 /* Serial Data Input in Eprom */
+#define EN_CCMD 0x000 /* Chip's command register */
+#define EN0_RSARLO 0x008 /* Remote start address reg 0 */
+#define EN0_RSARHI 0x009 /* Remote start address reg 1 */
+#define EN0_RCNTLO 0x00A /* Remote byte count reg WR */
+#define EN0_RCNTHI 0x00B /* Remote byte count reg WR */
+#define EN0_DCFG 0x00E /* Data configuration reg WR */
+#define EN0_PORT 0x010 /* Rcv missed frame error counter RD */
+#define ENC_PAGE0 0x000 /* Select page 0 of chip registers */
+#define ENC_PAGE3 0x0C0 /* Select page 3 of chip registers */
+static int mxser_read_register(int port, unsigned short *regs)
+{
+ int i, k, value, id;
+ unsigned int j;
+
+ id = mxser_program_mode(port);
+ if (id < 0)
+ return id;
+ for (i = 0; i < 14; i++) {
+ k = (i & 0x3F) | 0x180;
+ for (j = 0x100; j > 0; j >>= 1) {
+ outb(CHIP_CS, port);
+ if (k & j) {
+ outb(CHIP_CS | CHIP_DO, port);
+ outb(CHIP_CS | CHIP_DO | CHIP_SK, port); /* A? bit of read */
+ } else {
+ outb(CHIP_CS, port);
+ outb(CHIP_CS | CHIP_SK, port); /* A? bit of read */
+ }
}
- default:
- return -ENOIOCTLCMD;
+ (void)inb(port);
+ value = 0;
+ for (k = 0, j = 0x8000; k < 16; k++, j >>= 1) {
+ outb(CHIP_CS, port);
+ outb(CHIP_CS | CHIP_SK, port);
+ if (inb(port) & CHIP_DI)
+ value |= j;
+ }
+ regs[i] = value;
+ outb(0, port);
}
- return 0;
+ mxser_normal_mode(port);
+ return id;
}

#ifndef CMSPAR
@@ -1609,6 +1765,251 @@ static int mxser_ioctl_special(unsigned
return 0;
}

+static int mxser_ioctl(struct tty_struct *tty, struct file *file,
+ unsigned int cmd, unsigned long arg)
+{
+ struct mxser_port *info = tty->driver_data;
+ struct async_icount cprev, cnow; /* kernel counter temps */
+ struct serial_icounter_struct __user *p_cuser;
+ unsigned long templ;
+ unsigned long flags;
+ void __user *argp = (void __user *)arg;
+ int retval;
+
+ if (tty->index == MXSER_PORTS)
+ return mxser_ioctl_special(cmd, argp);
+
+ /* following add by Victor Yu. 01-05-2004 */
+ if (cmd == MOXA_SET_OP_MODE || cmd == MOXA_GET_OP_MODE) {
+ int p;
+ unsigned long opmode;
+ static unsigned char ModeMask[] = { 0xfc, 0xf3, 0xcf, 0x3f };
+ int shiftbit;
+ unsigned char val, mask;
+
+ p = tty->index % 4;
+ if (cmd == MOXA_SET_OP_MODE) {
+ if (get_user(opmode, (int __user *) argp))
+ return -EFAULT;
+ if (opmode != RS232_MODE &&
+ opmode != RS485_2WIRE_MODE &&
+ opmode != RS422_MODE &&
+ opmode != RS485_4WIRE_MODE)
+ return -EFAULT;
+ mask = ModeMask[p];
+ shiftbit = p * 2;
+ val = inb(info->opmode_ioaddr);
+ val &= mask;
+ val |= (opmode << shiftbit);
+ outb(val, info->opmode_ioaddr);
+ } else {
+ shiftbit = p * 2;
+ opmode = inb(info->opmode_ioaddr) >> shiftbit;
+ opmode &= OP_MODE_MASK;
+ if (copy_to_user(argp, &opmode, sizeof(int)))
+ return -EFAULT;
+ }
+ return 0;
+ }
+ /* above add by Victor Yu. 01-05-2004 */
+
+ if ((cmd != TIOCGSERIAL) && (cmd != TIOCMIWAIT) && (cmd != TIOCGICOUNT)) {
+ if (tty->flags & (1 << TTY_IO_ERROR))
+ return -EIO;
+ }
+ switch (cmd) {
+ case TCSBRK: /* SVID version: non-zero arg --> no break */
+ retval = tty_check_change(tty);
+ if (retval)
+ return retval;
+ tty_wait_until_sent(tty, 0);
+ if (!arg)
+ mxser_send_break(info, HZ / 4); /* 1/4 second */
+ return 0;
+ case TCSBRKP: /* support for POSIX tcsendbreak() */
+ retval = tty_check_change(tty);
+ if (retval)
+ return retval;
+ tty_wait_until_sent(tty, 0);
+ mxser_send_break(info, arg ? arg * (HZ / 10) : HZ / 4);
+ return 0;
+ case TIOCGSOFTCAR:
+ return put_user(C_CLOCAL(tty) ? 1 : 0, (unsigned long __user *)argp);
+ case TIOCSSOFTCAR:
+ if (get_user(templ, (unsigned long __user *) argp))
+ return -EFAULT;
+ arg = templ;
+ tty->termios->c_cflag = ((tty->termios->c_cflag & ~CLOCAL) | (arg ? CLOCAL : 0));
+ return 0;
+ case TIOCGSERIAL:
+ return mxser_get_serial_info(info, argp);
+ case TIOCSSERIAL:
+ return mxser_set_serial_info(info, argp);
+ case TIOCSERGETLSR: /* Get line status register */
+ return mxser_get_lsr_info(info, argp);
+ /*
+ * Wait for any of the 4 modem inputs (DCD,RI,DSR,CTS) to change
+ * - mask passed in arg for lines of interest
+ * (use |'ed TIOCM_RNG/DSR/CD/CTS for masking)
+ * Caller should use TIOCGICOUNT to see which one it was
+ */
+ case TIOCMIWAIT: {
+ DECLARE_WAITQUEUE(wait, current);
+ int ret;
+ spin_lock_irqsave(&info->slock, flags);
+ cprev = info->icount; /* note the counters on entry */
+ spin_unlock_irqrestore(&info->slock, flags);
+
+ add_wait_queue(&info->delta_msr_wait, &wait);
+ while (1) {
+ spin_lock_irqsave(&info->slock, flags);
+ cnow = info->icount; /* atomic copy */
+ spin_unlock_irqrestore(&info->slock, flags);
+
+ set_current_state(TASK_INTERRUPTIBLE);
+ if (((arg & TIOCM_RNG) &&
+ (cnow.rng != cprev.rng)) ||
+ ((arg & TIOCM_DSR) &&
+ (cnow.dsr != cprev.dsr)) ||
+ ((arg & TIOCM_CD) &&
+ (cnow.dcd != cprev.dcd)) ||
+ ((arg & TIOCM_CTS) &&
+ (cnow.cts != cprev.cts))) {
+ ret = 0;
+ break;
+ }
+ /* see if a signal did it */
+ if (signal_pending(current)) {
+ ret = -ERESTARTSYS;
+ break;
+ }
+ cprev = cnow;
+ }
+ current->state = TASK_RUNNING;
+ remove_wait_queue(&info->delta_msr_wait, &wait);
+ break;
+ }
+ /* NOTREACHED */
+ /*
+ * Get counter of input serial line interrupts (DCD,RI,DSR,CTS)
+ * Return: write counters to the user passed counter struct
+ * NB: both 1->0 and 0->1 transitions are counted except for
+ * RI where only 0->1 is counted.
+ */
+ case TIOCGICOUNT:
+ spin_lock_irqsave(&info->slock, flags);
+ cnow = info->icount;
+ spin_unlock_irqrestore(&info->slock, flags);
+ p_cuser = argp;
+ /* modified by casper 1/11/2000 */
+ if (put_user(cnow.frame, &p_cuser->frame))
+ return -EFAULT;
+ if (put_user(cnow.brk, &p_cuser->brk))
+ return -EFAULT;
+ if (put_user(cnow.overrun, &p_cuser->overrun))
+ return -EFAULT;
+ if (put_user(cnow.buf_overrun, &p_cuser->buf_overrun))
+ return -EFAULT;
+ if (put_user(cnow.parity, &p_cuser->parity))
+ return -EFAULT;
+ if (put_user(cnow.rx, &p_cuser->rx))
+ return -EFAULT;
+ if (put_user(cnow.tx, &p_cuser->tx))
+ return -EFAULT;
+ put_user(cnow.cts, &p_cuser->cts);
+ put_user(cnow.dsr, &p_cuser->dsr);
+ put_user(cnow.rng, &p_cuser->rng);
+ put_user(cnow.dcd, &p_cuser->dcd);
+ return 0;
+ case MOXA_HighSpeedOn:
+ return put_user(info->baud_base != 115200 ? 1 : 0, (int __user *)argp);
+ case MOXA_SDS_RSTICOUNTER:
+ info->mon_data.rxcnt = 0;
+ info->mon_data.txcnt = 0;
+ return 0;
+/* (above) added by James. */
+ case MOXA_ASPP_SETBAUD:{
+ long baud;
+ if (get_user(baud, (long __user *)argp))
+ return -EFAULT;
+ mxser_set_baud(info, baud);
+ return 0;
+ }
+ case MOXA_ASPP_GETBAUD:
+ if (copy_to_user(argp, &info->realbaud, sizeof(long)))
+ return -EFAULT;
+
+ return 0;
+
+ case MOXA_ASPP_OQUEUE:{
+ int len, lsr;
+
+ len = mxser_chars_in_buffer(tty);
+
+ lsr = inb(info->ioaddr + UART_LSR) & UART_LSR_TEMT;
+
+ len += (lsr ? 0 : 1);
+
+ if (copy_to_user(argp, &len, sizeof(int)))
+ return -EFAULT;
+
+ return 0;
+ }
+ case MOXA_ASPP_MON: {
+ int mcr, status;
+
+ /* info->mon_data.ser_param = tty->termios->c_cflag; */
+
+ status = mxser_get_msr(info->ioaddr, 1, tty->index);
+ mxser_check_modem_status(info, status);
+
+ mcr = inb(info->ioaddr + UART_MCR);
+ if (mcr & MOXA_MUST_MCR_XON_FLAG)
+ info->mon_data.hold_reason &= ~NPPI_NOTIFY_XOFFHOLD;
+ else
+ info->mon_data.hold_reason |= NPPI_NOTIFY_XOFFHOLD;
+
+ if (mcr & MOXA_MUST_MCR_TX_XON)
+ info->mon_data.hold_reason &= ~NPPI_NOTIFY_XOFFXENT;
+ else
+ info->mon_data.hold_reason |= NPPI_NOTIFY_XOFFXENT;
+
+ if (info->tty->hw_stopped)
+ info->mon_data.hold_reason |= NPPI_NOTIFY_CTSHOLD;
+ else
+ info->mon_data.hold_reason &= ~NPPI_NOTIFY_CTSHOLD;
+
+ if (copy_to_user(argp, &info->mon_data,
+ sizeof(struct mxser_mon)))
+ return -EFAULT;
+
+ return 0;
+ }
+ case MOXA_ASPP_LSTATUS: {
+ if (copy_to_user(argp, &info->err_shadow,
+ sizeof(unsigned char)))
+ return -EFAULT;
+
+ info->err_shadow = 0;
+ return 0;
+ }
+ case MOXA_SET_BAUD_METHOD: {
+ int method;
+
+ if (get_user(method, (int __user *)argp))
+ return -EFAULT;
+ mxser_set_baud_method[tty->index] = method;
+ if (copy_to_user(argp, &method, sizeof(int)))
+ return -EFAULT;
+
+ return 0;
+ }
+ default:
+ return -ENOIOCTLCMD;
+ }
+ return 0;
+}
+
static void mxser_stoprx(struct tty_struct *tty)
{
struct mxser_port *info = tty->driver_data;
@@ -1633,10 +2034,20 @@ static void mxser_stoprx(struct tty_stru
}
}

-static void mxser_startrx(struct tty_struct *tty)
+/*
+ * This routine is called by the upper-layer tty layer to signal that
+ * incoming characters should be throttled.
+ */
+static void mxser_throttle(struct tty_struct *tty)
+{
+ mxser_stoprx(tty);
+}
+
+static void mxser_unthrottle(struct tty_struct *tty)
{
struct mxser_port *info = tty->driver_data;

+ /* startrx */
info->ldisc_stop_rx = 0;
if (I_IXOFF(tty)) {
if (info->x_char)
@@ -1662,17 +2073,37 @@ static void mxser_startrx(struct tty_str
}

/*
- * This routine is called by the upper-layer tty layer to signal that
- * incoming characters should be throttled.
+ * mxser_stop() and mxser_start()
+ *
+ * This routines are called before setting or resetting tty->stopped.
+ * They enable or disable transmitter interrupts, as necessary.
*/
-static void mxser_throttle(struct tty_struct *tty)
+static void mxser_stop(struct tty_struct *tty)
{
- mxser_stoprx(tty);
+ struct mxser_port *info = tty->driver_data;
+ unsigned long flags;
+
+ spin_lock_irqsave(&info->slock, flags);
+ if (info->IER & UART_IER_THRI) {
+ info->IER &= ~UART_IER_THRI;
+ outb(info->IER, info->ioaddr + UART_IER);
+ }
+ spin_unlock_irqrestore(&info->slock, flags);
}

-static void mxser_unthrottle(struct tty_struct *tty)
+static void mxser_start(struct tty_struct *tty)
{
- mxser_startrx(tty);
+ struct mxser_port *info = tty->driver_data;
+ unsigned long flags;
+
+ spin_lock_irqsave(&info->slock, flags);
+ if (info->xmit_cnt && info->xmit_buf
+ /* && !(info->IER & UART_IER_THRI) */) {
+ outb(info->IER & ~UART_IER_THRI, info->ioaddr + UART_IER);
+ info->IER |= UART_IER_THRI;
+ outb(info->IER, info->ioaddr + UART_IER);
+ }
+ spin_unlock_irqrestore(&info->slock, flags);
}

static void mxser_set_termios(struct tty_struct *tty, struct termios *old_termios)
@@ -1710,40 +2141,6 @@ static void mxser_set_termios(struct tty
}

/*
- * mxser_stop() and mxser_start()
- *
- * This routines are called before setting or resetting tty->stopped.
- * They enable or disable transmitter interrupts, as necessary.
- */
-static void mxser_stop(struct tty_struct *tty)
-{
- struct mxser_port *info = tty->driver_data;
- unsigned long flags;
-
- spin_lock_irqsave(&info->slock, flags);
- if (info->IER & UART_IER_THRI) {
- info->IER &= ~UART_IER_THRI;
- outb(info->IER, info->ioaddr + UART_IER);
- }
- spin_unlock_irqrestore(&info->slock, flags);
-}
-
-static void mxser_start(struct tty_struct *tty)
-{
- struct mxser_port *info = tty->driver_data;
- unsigned long flags;
-
- spin_lock_irqsave(&info->slock, flags);
- if (info->xmit_cnt && info->xmit_buf
- /* && !(info->IER & UART_IER_THRI) */) {
- outb(info->IER & ~UART_IER_THRI, info->ioaddr + UART_IER);
- info->IER |= UART_IER_THRI;
- outb(info->IER, info->ioaddr + UART_IER);
- }
- spin_unlock_irqrestore(&info->slock, flags);
-}
-
-/*
* mxser_wait_until_sent() --- wait until the transmitter is empty
*/
static void mxser_wait_until_sent(struct tty_struct *tty, int timeout)
@@ -1845,122 +2242,6 @@ static void mxser_rs_break(struct tty_st

/* (above) added by James. */

-
-/*
- * This is the serial driver's generic interrupt routine
- */
-static irqreturn_t mxser_interrupt(int irq, void *dev_id, struct pt_regs *regs)
-{
- int status, iir, i;
- struct mxser_board *brd = NULL;
- struct mxser_port *port;
- int max, irqbits, bits, msr;
- int pass_counter = 0;
- unsigned int int_cnt;
- int handled = IRQ_NONE;
-
- /* spin_lock(&gm_lock); */
-
- for (i = 0; i < MXSER_BOARDS; i++)
- if (dev_id == &mxser_boards[i]) {
- brd = dev_id;
- break;
- }
-
- if (i == MXSER_BOARDS)
- goto irq_stop;
- if (brd == NULL)
- goto irq_stop;
- max = mxser_numports[brd->board_type - 1];
- while (1) {
- irqbits = inb(brd->vector) & brd->vector_mask;
- if (irqbits == brd->vector_mask)
- break;
-
- handled = IRQ_HANDLED;
- for (i = 0, bits = 1; i < max; i++, irqbits |= bits, bits <<= 1) {
- if (irqbits == brd->vector_mask)
- break;
- if (bits & irqbits)
- continue;
- port = &brd->ports[i];
-
- int_cnt = 0;
- do {
- /* following add by Victor Yu. 09-13-2002 */
- iir = inb(port->ioaddr + UART_IIR);
- if (iir & UART_IIR_NO_INT)
- break;
- iir &= MOXA_MUST_IIR_MASK;
- if (!port->tty) {
- status = inb(port->ioaddr + UART_LSR);
- outb(0x27, port->ioaddr + UART_FCR);
- inb(port->ioaddr + UART_MSR);
- break;
- }
- /* above add by Victor Yu. 09-13-2002 */
-
- /* following add by Victor Yu. 09-02-2002 */
- status = inb(port->ioaddr + UART_LSR);
-
- if (status & UART_LSR_PE)
- port->err_shadow |= NPPI_NOTIFY_PARITY;
- if (status & UART_LSR_FE)
- port->err_shadow |= NPPI_NOTIFY_FRAMING;
- if (status & UART_LSR_OE)
- port->err_shadow |=
- NPPI_NOTIFY_HW_OVERRUN;
- if (status & UART_LSR_BI)
- port->err_shadow |= NPPI_NOTIFY_BREAK;
-
- if (port->board->chip_flag) {
- /*
- if ( (status & 0x02) && !(status & 0x01) ) {
- outb(port->ioaddr+UART_FCR, 0x23);
- continue;
- }
- */
- if (iir == MOXA_MUST_IIR_GDA ||
- iir == MOXA_MUST_IIR_RDA ||
- iir == MOXA_MUST_IIR_RTO ||
- iir == MOXA_MUST_IIR_LSR)
- mxser_receive_chars(port,
- &status);
-
- } else {
- /* above add by Victor Yu. 09-02-2002 */
-
- status &= port->read_status_mask;
- if (status & UART_LSR_DR)
- mxser_receive_chars(port,
- &status);
- }
- msr = inb(port->ioaddr + UART_MSR);
- if (msr & UART_MSR_ANY_DELTA)
- mxser_check_modem_status(port, msr);
-
- /* following add by Victor Yu. 09-13-2002 */
- if (port->board->chip_flag) {
- if (iir == 0x02 && (status &
- UART_LSR_THRE))
- mxser_transmit_chars(port);
- } else {
- /* above add by Victor Yu. 09-13-2002 */
-
- if (status & UART_LSR_THRE)
- mxser_transmit_chars(port);
- }
- } while (int_cnt++ < MXSER_ISR_PASS_LIMIT);
- }
- if (pass_counter++ > MXSER_ISR_PASS_LIMIT)
- break; /* Prevent infinite loops */
- }
-
- irq_stop:
- /* spin_unlock(&gm_lock); */
- return handled;
-}
-
static void mxser_receive_chars(struct mxser_port *port, int *status)
{
struct tty_struct *tty = port->tty;
@@ -2155,744 +2436,202 @@ unlock:
spin_unlock_irqrestore(&port->slock, flags);
}

-static void mxser_check_modem_status(struct mxser_port *port, int status)
+/*
+ * This is the serial driver's generic interrupt routine
+ */
+static irqreturn_t mxser_interrupt(int irq, void *dev_id, struct pt_regs *regs)
{
- /* update input line counters */
- if (status & UART_MSR_TERI)
- port->icount.rng++;
- if (status & UART_MSR_DDSR)
- port->icount.dsr++;
- if (status & UART_MSR_DDCD)
- port->icount.dcd++;
- if (status & UART_MSR_DCTS)
- port->icount.cts++;
- port->mon_data.modem_status = status;
- wake_up_interruptible(&port->delta_msr_wait);
-
- if ((port->flags & ASYNC_CHECK_CD) && (status & UART_MSR_DDCD)) {
- if (status & UART_MSR_DCD)
- wake_up_interruptible(&port->open_wait);
- schedule_work(&port->tqueue);
- }
+ int status, iir, i;
+ struct mxser_board *brd = NULL;
+ struct mxser_port *port;
+ int max, irqbits, bits, msr;
+ int pass_counter = 0;
+ unsigned int int_cnt;
+ int handled = IRQ_NONE;

- if (port->flags & ASYNC_CTS_FLOW) {
- if (port->tty->hw_stopped) {
- if (status & UART_MSR_CTS) {
- port->tty->hw_stopped = 0;
+ /* spin_lock(&gm_lock); */

- if ((port->type != PORT_16550A) &&
- (!port->board->chip_flag)) {
- outb(port->IER & ~UART_IER_THRI,
- port->ioaddr + UART_IER);
- port->IER |= UART_IER_THRI;
- outb(port->IER, port->ioaddr +
- UART_IER);
- }
- set_bit(MXSER_EVENT_TXLOW, &port->event);
- schedule_work(&port->tqueue);
- }
- } else {
- if (!(status & UART_MSR_CTS)) {
- port->tty->hw_stopped = 1;
- if (port->type != PORT_16550A &&
- !port->board->chip_flag) {
- port->IER &= ~UART_IER_THRI;
- outb(port->IER, port->ioaddr +
- UART_IER);
- }
- }
+ for (i = 0; i < MXSER_BOARDS; i++)
+ if (dev_id == &mxser_boards[i]) {
+ brd = dev_id;
+ break;
}
- }
-}
-
-static int mxser_block_til_ready(struct tty_struct *tty, struct file *filp, struct mxser_port *port)
-{
- DECLARE_WAITQUEUE(wait, current);
- int retval;
- int do_clocal = 0;
- unsigned long flags;

- /*
- * If non-blocking mode is set, or the port is not enabled,
- * then make the check up front and then exit.
- */
- if ((filp->f_flags & O_NONBLOCK) || (tty->flags & (1 << TTY_IO_ERROR))) {
- port->flags |= ASYNC_NORMAL_ACTIVE;
- return 0;
- }
-
- if (tty->termios->c_cflag & CLOCAL)
- do_clocal = 1;
-
- /*
- * Block waiting for the carrier detect and the line to become
- * free (i.e., not in use by the callout). While we are in
- * this loop, port->count is dropped by one, so that
- * mxser_close() knows when to free things. We restore it upon
- * exit, either normal or abnormal.
- */
- retval = 0;
- add_wait_queue(&port->open_wait, &wait);
-
- spin_lock_irqsave(&port->slock, flags);
- if (!tty_hung_up_p(filp))
- port->count--;
- spin_unlock_irqrestore(&port->slock, flags);
- port->blocked_open++;
+ if (i == MXSER_BOARDS)
+ goto irq_stop;
+ if (brd == NULL)
+ goto irq_stop;
+ max = mxser_numports[brd->board_type - 1];
while (1) {
- spin_lock_irqsave(&port->slock, flags);
- outb(inb(port->ioaddr + UART_MCR) |
- UART_MCR_DTR | UART_MCR_RTS, port->ioaddr + UART_MCR);
- spin_unlock_irqrestore(&port->slock, flags);
- set_current_state(TASK_INTERRUPTIBLE);
- if (tty_hung_up_p(filp) || !(port->flags & ASYNC_INITIALIZED)) {
- if (port->flags & ASYNC_HUP_NOTIFY)
- retval = -EAGAIN;
- else
- retval = -ERESTARTSYS;
- break;
- }
- if (!(port->flags & ASYNC_CLOSING) &&
- (do_clocal ||
- (inb(port->ioaddr + UART_MSR) & UART_MSR_DCD)))
- break;
- if (signal_pending(current)) {
- retval = -ERESTARTSYS;
+ irqbits = inb(brd->vector) & brd->vector_mask;
+ if (irqbits == brd->vector_mask)
break;
- }
- schedule();
- }
- set_current_state(TASK_RUNNING);
- remove_wait_queue(&port->open_wait, &wait);
- if (!tty_hung_up_p(filp))
- port->count++;
- port->blocked_open--;
- if (retval)
- return retval;
- port->flags |= ASYNC_NORMAL_ACTIVE;
- return 0;
-}
-
-static int mxser_startup(struct mxser_port *info)
-{
- unsigned long page;
- unsigned long flags;
-
- page = __get_free_page(GFP_KERNEL);
- if (!page)
- return -ENOMEM;
-
- spin_lock_irqsave(&info->slock, flags);
-
- if (info->flags & ASYNC_INITIALIZED) {
- free_page(page);
- spin_unlock_irqrestore(&info->slock, flags);
- return 0;
- }

- if (!info->ioaddr || !info->type) {
- if (info->tty)
- set_bit(TTY_IO_ERROR, &info->tty->flags);
- free_page(page);
- spin_unlock_irqrestore(&info->slock, flags);
- return 0;
- }
- if (info->xmit_buf)
- free_page(page);
- else
- info->xmit_buf = (unsigned char *) page;
-
- /*
- * Clear the FIFO buffers and disable them
- * (they will be reenabled in mxser_change_speed())
- */
- if (info->board->chip_flag)
- outb((UART_FCR_CLEAR_RCVR |
- UART_FCR_CLEAR_XMIT |
- MOXA_MUST_FCR_GDA_MODE_ENABLE), info->ioaddr + UART_FCR);
- else
- outb((UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT),
- info->ioaddr + UART_FCR);
-
- /*
- * At this point there's no way the LSR could still be 0xFF;
- * if it is, then bail out, because there's likely no UART
- * here.
- */
- if (inb(info->ioaddr + UART_LSR) == 0xff) {
- spin_unlock_irqrestore(&info->slock, flags);
- if (capable(CAP_SYS_ADMIN)) {
- if (info->tty)
- set_bit(TTY_IO_ERROR, &info->tty->flags);
- return 0;
- } else
- return -ENODEV;
- }
-
- /*
- * Clear the interrupt registers.
- */
- (void) inb(info->ioaddr + UART_LSR);
- (void) inb(info->ioaddr + UART_RX);
- (void) inb(info->ioaddr + UART_IIR);
- (void) inb(info->ioaddr + UART_MSR);
-
- /*
- * Now, initialize the UART
- */
- outb(UART_LCR_WLEN8, info->ioaddr + UART_LCR); /* reset DLAB */
- info->MCR = UART_MCR_DTR | UART_MCR_RTS;
- outb(info->MCR, info->ioaddr + UART_MCR);
-
- /*
- * Finally, enable interrupts
- */
- info->IER = UART_IER_MSI | UART_IER_RLSI | UART_IER_RDI;
- /* info->IER = UART_IER_RLSI | UART_IER_RDI; */
-
- /* following add by Victor Yu. 08-30-2002 */
- if (info->board->chip_flag)
- info->IER |= MOXA_MUST_IER_EGDAI;
- /* above add by Victor Yu. 08-30-2002 */
- outb(info->IER, info->ioaddr + UART_IER); /* enable interrupts */
-
- /*
- * And clear the interrupt registers again for luck.
- */
- (void) inb(info->ioaddr + UART_LSR);
- (void) inb(info->ioaddr + UART_RX);
- (void) inb(info->ioaddr + UART_IIR);
- (void) inb(info->ioaddr + UART_MSR);
-
- if (info->tty)
- clear_bit(TTY_IO_ERROR, &info->tty->flags);
- info->xmit_cnt = info->xmit_head = info->xmit_tail = 0;
-
- /*
- * and set the speed of the serial port
- */
- spin_unlock_irqrestore(&info->slock, flags);
- mxser_change_speed(info, NULL);
-
- info->flags |= ASYNC_INITIALIZED;
- return 0;
-}
-
-/*
- * This routine will shutdown a serial port; interrupts maybe disabled, and
- * DTR is dropped if the hangup on close termio flag is on.
- */
-static void mxser_shutdown(struct mxser_port *info)
-{
- unsigned long flags;
-
- if (!(info->flags & ASYNC_INITIALIZED))
- return;
-
- spin_lock_irqsave(&info->slock, flags);
-
- /*
- * clear delta_msr_wait queue to avoid mem leaks: we may free the irq
- * here so the queue might never be waken up
- */
- wake_up_interruptible(&info->delta_msr_wait);
-
- /*
- * Free the IRQ, if necessary
- */
- if (info->xmit_buf) {
- free_page((unsigned long) info->xmit_buf);
- info->xmit_buf = NULL;
- }
-
- info->IER = 0;
- outb(0x00, info->ioaddr + UART_IER);
-
- if (!info->tty || (info->tty->termios->c_cflag & HUPCL))
- info->MCR &= ~(UART_MCR_DTR | UART_MCR_RTS);
- outb(info->MCR, info->ioaddr + UART_MCR);
-
- /* clear Rx/Tx FIFO's */
- /* following add by Victor Yu. 08-30-2002 */
- if (info->board->chip_flag)
- outb(UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT |
- MOXA_MUST_FCR_GDA_MODE_ENABLE,
- info->ioaddr + UART_FCR);
- else
- /* above add by Victor Yu. 08-30-2002 */
- outb(UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT,
- info->ioaddr + UART_FCR);
-
- /* read data port to reset things */
- (void) inb(info->ioaddr + UART_RX);
-
- if (info->tty)
- set_bit(TTY_IO_ERROR, &info->tty->flags);
-
- info->flags &= ~ASYNC_INITIALIZED;
-
- /* following add by Victor Yu. 09-23-2002 */
- if (info->board->chip_flag)
- SET_MOXA_MUST_NO_SOFTWARE_FLOW_CONTROL(info->ioaddr);
- /* above add by Victor Yu. 09-23-2002 */
-
- spin_unlock_irqrestore(&info->slock, flags);
-}
-
-/*
- * This routine is called to set the UART divisor registers to match
- * the specified baud rate for a serial port.
- */
-static int mxser_change_speed(struct mxser_port *info,
- struct termios *old_termios)
-{
- unsigned cflag, cval, fcr;
- int ret = 0;
- unsigned char status;
- long baud;
- unsigned long flags;
-
- if (!info->tty || !info->tty->termios)
- return ret;
- cflag = info->tty->termios->c_cflag;
- if (!(info->ioaddr))
- return ret;
-
-#ifndef B921600
-#define B921600 (B460800 +1)
-#endif
- if (mxser_set_baud_method[info->tty->index] == 0) {
- baud = tty_get_baud_rate(info->tty);
- mxser_set_baud(info, baud);
- }
-
- /* byte size and parity */
- switch (cflag & CSIZE) {
- case CS5:
- cval = 0x00;
- break;
- case CS6:
- cval = 0x01;
- break;
- case CS7:
- cval = 0x02;
- break;
- case CS8:
- cval = 0x03;
- break;
- default:
- cval = 0x00;
- break; /* too keep GCC shut... */
- }
- if (cflag & CSTOPB)
- cval |= 0x04;
- if (cflag & PARENB)
- cval |= UART_LCR_PARITY;
- if (!(cflag & PARODD))
- cval |= UART_LCR_EPAR;
- if (cflag & CMSPAR)
- cval |= UART_LCR_SPAR;
-
- if ((info->type == PORT_8250) || (info->type == PORT_16450)) {
- if (info->board->chip_flag) {
- fcr = UART_FCR_ENABLE_FIFO;
- fcr |= MOXA_MUST_FCR_GDA_MODE_ENABLE;
- SET_MOXA_MUST_FIFO_VALUE(info);
- } else
- fcr = 0;
- } else {
- fcr = UART_FCR_ENABLE_FIFO;
- /* following add by Victor Yu. 08-30-2002 */
- if (info->board->chip_flag) {
- fcr |= MOXA_MUST_FCR_GDA_MODE_ENABLE;
- SET_MOXA_MUST_FIFO_VALUE(info);
- } else {
- /* above add by Victor Yu. 08-30-2002 */
- switch (info->rx_trigger) {
- case 1:
- fcr |= UART_FCR_TRIGGER_1;
- break;
- case 4:
- fcr |= UART_FCR_TRIGGER_4;
- break;
- case 8:
- fcr |= UART_FCR_TRIGGER_8;
- break;
- default:
- fcr |= UART_FCR_TRIGGER_14;
+ handled = IRQ_HANDLED;
+ for (i = 0, bits = 1; i < max; i++, irqbits |= bits, bits <<= 1) {
+ if (irqbits == brd->vector_mask)
break;
- }
- }
- }
+ if (bits & irqbits)
+ continue;
+ port = &brd->ports[i];

- /* CTS flow control flag and modem status interrupts */
- info->IER &= ~UART_IER_MSI;
- info->MCR &= ~UART_MCR_AFE;
- if (cflag & CRTSCTS) {
- info->flags |= ASYNC_CTS_FLOW;
- info->IER |= UART_IER_MSI;
- if ((info->type == PORT_16550A) || (info->board->chip_flag)) {
- info->MCR |= UART_MCR_AFE;
-/* status = mxser_get_msr(info->ioaddr, 0, info->port); */
-/*
- save_flags(flags);
- cli();
- status = inb(baseaddr + UART_MSR);
- restore_flags(flags);
-*/
- /* mxser_check_modem_status(info, status); */
- } else {
-/* status = mxser_get_msr(info->ioaddr, 0, info->port); */
- /* MX_LOCK(&info->slock); */
- status = inb(info->ioaddr + UART_MSR);
- /* MX_UNLOCK(&info->slock); */
- if (info->tty->hw_stopped) {
- if (status & UART_MSR_CTS) {
- info->tty->hw_stopped = 0;
- if (info->type != PORT_16550A &&
- !info->board->chip_flag) {
- outb(info->IER & ~UART_IER_THRI,
- info->ioaddr +
- UART_IER);
- info->IER |= UART_IER_THRI;
- outb(info->IER, info->ioaddr +
- UART_IER);
- }
- set_bit(MXSER_EVENT_TXLOW, &info->event);
- schedule_work(&info->tqueue); }
- } else {
- if (!(status & UART_MSR_CTS)) {
- info->tty->hw_stopped = 1;
- if ((info->type != PORT_16550A) &&
- (!info->board->chip_flag)) {
- info->IER &= ~UART_IER_THRI;
- outb(info->IER, info->ioaddr +
- UART_IER);
- }
+ int_cnt = 0;
+ do {
+ /* following add by Victor Yu. 09-13-2002 */
+ iir = inb(port->ioaddr + UART_IIR);
+ if (iir & UART_IIR_NO_INT)
+ break;
+ iir &= MOXA_MUST_IIR_MASK;
+ if (!port->tty) {
+ status = inb(port->ioaddr + UART_LSR);
+ outb(0x27, port->ioaddr + UART_FCR);
+ inb(port->ioaddr + UART_MSR);
+ break;
}
- }
- }
- } else {
- info->flags &= ~ASYNC_CTS_FLOW;
- }
- outb(info->MCR, info->ioaddr + UART_MCR);
- if (cflag & CLOCAL) {
- info->flags &= ~ASYNC_CHECK_CD;
- } else {
- info->flags |= ASYNC_CHECK_CD;
- info->IER |= UART_IER_MSI;
- }
- outb(info->IER, info->ioaddr + UART_IER);
-
- /*
- * Set up parity check flag
- */
- info->read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR;
- if (I_INPCK(info->tty))
- info->read_status_mask |= UART_LSR_FE | UART_LSR_PE;
- if (I_BRKINT(info->tty) || I_PARMRK(info->tty))
- info->read_status_mask |= UART_LSR_BI;
-
- info->ignore_status_mask = 0;
-
- if (I_IGNBRK(info->tty)) {
- info->ignore_status_mask |= UART_LSR_BI;
- info->read_status_mask |= UART_LSR_BI;
- /*
- * If we're ignore parity and break indicators, ignore
- * overruns too. (For real raw support).
- */
- if (I_IGNPAR(info->tty)) {
- info->ignore_status_mask |=
- UART_LSR_OE |
- UART_LSR_PE |
- UART_LSR_FE;
- info->read_status_mask |=
- UART_LSR_OE |
- UART_LSR_PE |
- UART_LSR_FE;
- }
- }
- /* following add by Victor Yu. 09-02-2002 */
- if (info->board->chip_flag) {
- spin_lock_irqsave(&info->slock, flags);
- SET_MOXA_MUST_XON1_VALUE(info->ioaddr, START_CHAR(info->tty));
- SET_MOXA_MUST_XOFF1_VALUE(info->ioaddr, STOP_CHAR(info->tty));
- if (I_IXON(info->tty)) {
- ENABLE_MOXA_MUST_RX_SOFTWARE_FLOW_CONTROL(info->ioaddr);
- } else {
- DISABLE_MOXA_MUST_RX_SOFTWARE_FLOW_CONTROL(info->ioaddr);
- }
- if (I_IXOFF(info->tty)) {
- ENABLE_MOXA_MUST_TX_SOFTWARE_FLOW_CONTROL(info->ioaddr);
- } else {
- DISABLE_MOXA_MUST_TX_SOFTWARE_FLOW_CONTROL(info->ioaddr);
- }
- /*
- if ( I_IXANY(info->tty) ) {
- info->MCR |= MOXA_MUST_MCR_XON_ANY;
- ENABLE_MOXA_MUST_XON_ANY_FLOW_CONTROL(info->ioaddr);
- } else {
- info->MCR &= ~MOXA_MUST_MCR_XON_ANY;
- DISABLE_MOXA_MUST_XON_ANY_FLOW_CONTROL(info->ioaddr);
- }
- */
- spin_unlock_irqrestore(&info->slock, flags);
- }
- /* above add by Victor Yu. 09-02-2002 */
-
-
- outb(fcr, info->ioaddr + UART_FCR); /* set fcr */
- outb(cval, info->ioaddr + UART_LCR);
-
- return ret;
-}
-
-
-static int mxser_set_baud(struct mxser_port *info, long newspd)
-{
- int quot = 0;
- unsigned char cval;
- int ret = 0;
- unsigned long flags;
-
- if (!info->tty || !info->tty->termios)
- return ret;
-
- if (!(info->ioaddr))
- return ret;
-
- if (newspd > info->max_baud)
- return 0;
-
- info->realbaud = newspd;
- if (newspd == 134) {
- quot = (2 * info->baud_base / 269);
- } else if (newspd) {
- quot = info->baud_base / newspd;
- if (quot == 0)
- quot = 1;
- } else {
- quot = 0;
- }
-
- info->timeout = ((info->xmit_fifo_size * HZ * 10 * quot) / info->baud_base);
- info->timeout += HZ / 50; /* Add .02 seconds of slop */
-
- if (quot) {
- spin_lock_irqsave(&info->slock, flags);
- info->MCR |= UART_MCR_DTR;
- outb(info->MCR, info->ioaddr + UART_MCR);
- spin_unlock_irqrestore(&info->slock, flags);
- } else {
- spin_lock_irqsave(&info->slock, flags);
- info->MCR &= ~UART_MCR_DTR;
- outb(info->MCR, info->ioaddr + UART_MCR);
- spin_unlock_irqrestore(&info->slock, flags);
- return ret;
- }
-
- cval = inb(info->ioaddr + UART_LCR);
-
- outb(cval | UART_LCR_DLAB, info->ioaddr + UART_LCR); /* set DLAB */
-
- outb(quot & 0xff, info->ioaddr + UART_DLL); /* LS of divisor */
- outb(quot >> 8, info->ioaddr + UART_DLM); /* MS of divisor */
- outb(cval, info->ioaddr + UART_LCR); /* reset DLAB */
-
-
- return ret;
-}
+ /* above add by Victor Yu. 09-13-2002 */

-/*
- * ------------------------------------------------------------
- * friends of mxser_ioctl()
- * ------------------------------------------------------------
- */
-static int mxser_get_serial_info(struct mxser_port *info,
- struct serial_struct __user *retinfo)
-{
- struct serial_struct tmp;
+ /* following add by Victor Yu. 09-02-2002 */
+ status = inb(port->ioaddr + UART_LSR);

- if (!retinfo)
- return -EFAULT;
- memset(&tmp, 0, sizeof(tmp));
- tmp.type = info->type;
- tmp.line = info->tty->index;
- tmp.port = info->ioaddr;
- tmp.irq = info->board->irq;
- tmp.flags = info->flags;
- tmp.baud_base = info->baud_base;
- tmp.close_delay = info->close_delay;
- tmp.closing_wait = info->closing_wait;
- tmp.custom_divisor = info->custom_divisor;
- tmp.hub6 = 0;
- if (copy_to_user(retinfo, &tmp, sizeof(*retinfo)))
- return -EFAULT;
- return 0;
-}
+ if (status & UART_LSR_PE)
+ port->err_shadow |= NPPI_NOTIFY_PARITY;
+ if (status & UART_LSR_FE)
+ port->err_shadow |= NPPI_NOTIFY_FRAMING;
+ if (status & UART_LSR_OE)
+ port->err_shadow |=
+ NPPI_NOTIFY_HW_OVERRUN;
+ if (status & UART_LSR_BI)
+ port->err_shadow |= NPPI_NOTIFY_BREAK;

-static int mxser_set_serial_info(struct mxser_port *info,
- struct serial_struct __user *new_info)
-{
- struct serial_struct new_serial;
- unsigned int flags;
- int retval = 0;
+ if (port->board->chip_flag) {
+ /*
+ if ( (status & 0x02) && !(status & 0x01) ) {
+ outb(port->ioaddr+UART_FCR, 0x23);
+ continue;
+ }
+ */
+ if (iir == MOXA_MUST_IIR_GDA ||
+ iir == MOXA_MUST_IIR_RDA ||
+ iir == MOXA_MUST_IIR_RTO ||
+ iir == MOXA_MUST_IIR_LSR)
+ mxser_receive_chars(port,
+ &status);

- if (!new_info || !info->ioaddr)
- return -EFAULT;
- if (copy_from_user(&new_serial, new_info, sizeof(new_serial)))
- return -EFAULT;
+ } else {
+ /* above add by Victor Yu. 09-02-2002 */

- if ((new_serial.irq != info->board->irq) ||
- (new_serial.port != info->ioaddr) ||
- (new_serial.custom_divisor != info->custom_divisor) ||
- (new_serial.baud_base != info->baud_base))
- return -EPERM;
+ status &= port->read_status_mask;
+ if (status & UART_LSR_DR)
+ mxser_receive_chars(port,
+ &status);
+ }
+ msr = inb(port->ioaddr + UART_MSR);
+ if (msr & UART_MSR_ANY_DELTA)
+ mxser_check_modem_status(port, msr);

- flags = info->flags & ASYNC_SPD_MASK;
+ /* following add by Victor Yu. 09-13-2002 */
+ if (port->board->chip_flag) {
+ if (iir == 0x02 && (status &
+ UART_LSR_THRE))
+ mxser_transmit_chars(port);
+ } else {
+ /* above add by Victor Yu. 09-13-2002 */

- if (!capable(CAP_SYS_ADMIN)) {
- if ((new_serial.baud_base != info->baud_base) ||
- (new_serial.close_delay != info->close_delay) ||
- ((new_serial.flags & ~ASYNC_USR_MASK) != (info->flags & ~ASYNC_USR_MASK)))
- return -EPERM;
- info->flags = ((info->flags & ~ASYNC_USR_MASK) |
- (new_serial.flags & ASYNC_USR_MASK));
- } else {
- /*
- * OK, past this point, all the error checking has been done.
- * At this point, we start making changes.....
- */
- info->flags = ((info->flags & ~ASYNC_FLAGS) |
- (new_serial.flags & ASYNC_FLAGS));
- info->close_delay = new_serial.close_delay * HZ / 100;
- info->closing_wait = new_serial.closing_wait * HZ / 100;
- info->tty->low_latency =
- (info->flags & ASYNC_LOW_LATENCY) ? 1 : 0;
- info->tty->low_latency = 0; /* (info->flags & ASYNC_LOW_LATENCY) ? 1 : 0; */
+ if (status & UART_LSR_THRE)
+ mxser_transmit_chars(port);
+ }
+ } while (int_cnt++ < MXSER_ISR_PASS_LIMIT);
+ }
+ if (pass_counter++ > MXSER_ISR_PASS_LIMIT)
+ break; /* Prevent infinite loops */
}

- /* added by casper, 3/17/2000, for mouse */
- info->type = new_serial.type;
-
- process_txrx_fifo(info);
-
- if (info->flags & ASYNC_INITIALIZED) {
- if (flags != (info->flags & ASYNC_SPD_MASK))
- mxser_change_speed(info, NULL);
- } else
- retval = mxser_startup(info);
-
- return retval;
+ irq_stop:
+ /* spin_unlock(&gm_lock); */
+ return handled;
}

-/*
- * mxser_get_lsr_info - get line status register info
- *
- * Purpose: Let user call ioctl() to get info when the UART physically
- * is emptied. On bus types like RS485, the transmitter must
- * release the bus after transmitting. This must be done when
- * the transmit shift register is empty, not be done when the
- * transmit holding register is empty. This functionality
- * allows an RS485 driver to be written in user space.
- */
-static int mxser_get_lsr_info(struct mxser_port *info,
- unsigned int __user *value)
-{
- unsigned char status;
- unsigned int result;
- unsigned long flags;
-
- spin_lock_irqsave(&info->slock, flags);
- status = inb(info->ioaddr + UART_LSR);
- spin_unlock_irqrestore(&info->slock, flags);
- result = ((status & UART_LSR_TEMT) ? TIOCSER_TEMT : 0);
- return put_user(result, value);
-}
+static const struct tty_operations mxser_ops = {
+ .open = mxser_open,
+ .close = mxser_close,
+ .write = mxser_write,
+ .put_char = mxser_put_char,
+ .flush_chars = mxser_flush_chars,
+ .write_room = mxser_write_room,
+ .chars_in_buffer = mxser_chars_in_buffer,
+ .flush_buffer = mxser_flush_buffer,
+ .ioctl = mxser_ioctl,
+ .throttle = mxser_throttle,
+ .unthrottle = mxser_unthrottle,
+ .set_termios = mxser_set_termios,
+ .stop = mxser_stop,
+ .start = mxser_start,
+ .hangup = mxser_hangup,
+ .break_ctl = mxser_rs_break,
+ .wait_until_sent = mxser_wait_until_sent,
+ .tiocmget = mxser_tiocmget,
+ .tiocmset = mxser_tiocmset,
+};

/*
- * This routine sends a break character out the serial port.
+ * The MOXA Smartio/Industio serial driver boot-time initialization code!
*/
-static void mxser_send_break(struct mxser_port *info, int duration)
-{
- unsigned long flags;

- if (!info->ioaddr)
- return;
- set_current_state(TASK_INTERRUPTIBLE);
- spin_lock_irqsave(&info->slock, flags);
- outb(inb(info->ioaddr + UART_LCR) | UART_LCR_SBC,
- info->ioaddr + UART_LCR);
- spin_unlock_irqrestore(&info->slock, flags);
- schedule_timeout(duration);
- spin_lock_irqsave(&info->slock, flags);
- outb(inb(info->ioaddr + UART_LCR) & ~UART_LCR_SBC,
- info->ioaddr + UART_LCR);
- spin_unlock_irqrestore(&info->slock, flags);
-}
-
-static int mxser_tiocmget(struct tty_struct *tty, struct file *file)
+static int __devinit mxser_initbrd(struct mxser_board *brd)
{
- struct mxser_port *info = tty->driver_data;
- unsigned char control, status;
- unsigned long flags;
-
-
- if (tty->index == MXSER_PORTS)
- return -ENOIOCTLCMD;
- if (tty->flags & (1 << TTY_IO_ERROR))
- return -EIO;
-
- control = info->MCR;
+ struct mxser_port *info;
+ unsigned int i;
+ int retval;

- spin_lock_irqsave(&info->slock, flags);
- status = inb(info->ioaddr + UART_MSR);
- if (status & UART_MSR_ANY_DELTA)
- mxser_check_modem_status(info, status);
- spin_unlock_irqrestore(&info->slock, flags);
- return ((control & UART_MCR_RTS) ? TIOCM_RTS : 0) |
- ((control & UART_MCR_DTR) ? TIOCM_DTR : 0) |
- ((status & UART_MSR_DCD) ? TIOCM_CAR : 0) |
- ((status & UART_MSR_RI) ? TIOCM_RNG : 0) |
- ((status & UART_MSR_DSR) ? TIOCM_DSR : 0) |
- ((status & UART_MSR_CTS) ? TIOCM_CTS : 0);
-}
+ printk(KERN_INFO "max. baud rate = %d bps.\n", brd->ports[0].max_baud);

-static int mxser_tiocmset(struct tty_struct *tty, struct file *file,
- unsigned int set, unsigned int clear)
-{
- struct mxser_port *info = tty->driver_data;
- unsigned long flags;
+ for (i = 0; i < brd->nports; i++) {
+ info = &brd->ports[i];
+ info->board = brd;
+ info->stop_rx = 0;
+ info->ldisc_stop_rx = 0;

+ /* Enhance mode enabled here */
+ if (brd->chip_flag != MOXA_OTHER_UART)
+ ENABLE_MOXA_MUST_ENCHANCE_MODE(info->ioaddr);

- if (tty->index == MXSER_PORTS)
- return -ENOIOCTLCMD;
- if (tty->flags & (1 << TTY_IO_ERROR))
- return -EIO;
+ info->flags = ASYNC_SHARE_IRQ;
+ info->type = brd->uart_type;

- spin_lock_irqsave(&info->slock, flags);
+ process_txrx_fifo(info);

- if (set & TIOCM_RTS)
- info->MCR |= UART_MCR_RTS;
- if (set & TIOCM_DTR)
- info->MCR |= UART_MCR_DTR;
+ info->custom_divisor = info->baud_base * 16;
+ info->close_delay = 5 * HZ / 10;
+ info->closing_wait = 30 * HZ;
+ INIT_WORK(&info->tqueue, mxser_do_softint, info);
+ info->normal_termios = mxvar_sdriver->init_termios;
+ init_waitqueue_head(&info->open_wait);
+ init_waitqueue_head(&info->close_wait);
+ init_waitqueue_head(&info->delta_msr_wait);
+ memset(&info->mon_data, 0, sizeof(struct mxser_mon));
+ info->err_shadow = 0;
+ spin_lock_init(&info->slock);

- if (clear & TIOCM_RTS)
- info->MCR &= ~UART_MCR_RTS;
- if (clear & TIOCM_DTR)
- info->MCR &= ~UART_MCR_DTR;
+ /* before set INT ISR, disable all int */
+ outb(inb(info->ioaddr + UART_IER) & 0xf0,
+ info->ioaddr + UART_IER);
+ }
+ /*
+ * Allocate the IRQ if necessary
+ */

- outb(info->MCR, info->ioaddr + UART_MCR);
- spin_unlock_irqrestore(&info->slock, flags);
+ retval = request_irq(brd->irq, mxser_interrupt,
+ (brd->ports[0].flags & ASYNC_SHARE_IRQ) ? IRQF_SHARED :
+ IRQF_DISABLED, "mxser", brd);
+ if (retval) {
+ printk(KERN_ERR "Board %s: Request irq failed, IRQ (%d) may "
+ "conflict with another device.\n",
+ mxser_brdname[brd->board_type - 1], brd->irq);
+ return retval;
+ }
return 0;
}

-
-static int mxser_read_register(int, unsigned short *);
-static int mxser_program_mode(int);
-static void mxser_normal_mode(int);
-
static int __init mxser_get_ISA_conf(int cap, struct mxser_board *brd)
{
int id, i, bits;
@@ -2988,111 +2727,303 @@ static int __init mxser_get_ISA_conf(int
return brd->nports;
}

-#define CHIP_SK 0x01 /* Serial Data Clock in Eprom */
-#define CHIP_DO 0x02 /* Serial Data Output in Eprom */
-#define CHIP_CS 0x04 /* Serial Chip Select in Eprom */
-#define CHIP_DI 0x08 /* Serial Data Input in Eprom */
-#define EN_CCMD 0x000 /* Chip's command register */
-#define EN0_RSARLO 0x008 /* Remote start address reg 0 */
-#define EN0_RSARHI 0x009 /* Remote start address reg 1 */
-#define EN0_RCNTLO 0x00A /* Remote byte count reg WR */
-#define EN0_RCNTHI 0x00B /* Remote byte count reg WR */
-#define EN0_DCFG 0x00E /* Data configuration reg WR */
-#define EN0_PORT 0x010 /* Rcv missed frame error counter RD */
-#define ENC_PAGE0 0x000 /* Select page 0 of chip registers */
-#define ENC_PAGE3 0x0C0 /* Select page 3 of chip registers */
-static int mxser_read_register(int port, unsigned short *regs)
+static int __init mxser_get_PCI_conf(int board_type, struct mxser_board *brd,
+ struct pci_dev *pdev)
{
- int i, k, value, id;
- unsigned int j;
+ unsigned int i, j;
+ unsigned long ioaddress;
+ int retval;

- id = mxser_program_mode(port);
- if (id < 0)
- return id;
- for (i = 0; i < 14; i++) {
- k = (i & 0x3F) | 0x180;
- for (j = 0x100; j > 0; j >>= 1) {
- outb(CHIP_CS, port);
- if (k & j) {
- outb(CHIP_CS | CHIP_DO, port);
- outb(CHIP_CS | CHIP_DO | CHIP_SK, port); /* A? bit of read */
- } else {
- outb(CHIP_CS, port);
- outb(CHIP_CS | CHIP_SK, port); /* A? bit of read */
+ /* io address */
+ brd->board_type = board_type;
+ brd->nports = mxser_numports[board_type - 1];
+ ioaddress = pci_resource_start(pdev, 2);
+ retval = pci_request_region(pdev, 2, "mxser(IO)");
+ if (retval)
+ goto err;
+
+ for (i = 0; i < brd->nports; i++)
+ brd->ports[i].ioaddr = ioaddress + 8 * i;
+
+ /* vector */
+ ioaddress = pci_resource_start(pdev, 3);
+ retval = pci_request_region(pdev, 3, "mxser(vector)");
+ if (retval)
+ goto err_relio;
+ brd->vector = ioaddress;
+
+ /* irq */
+ brd->irq = pdev->irq;
+
+ brd->chip_flag = CheckIsMoxaMust(brd->ports[0].ioaddr);
+ brd->uart_type = PORT_16550A;
+ brd->vector_mask = 0;
+
+ for (i = 0; i < brd->nports; i++) {
+ for (j = 0; j < UART_INFO_NUM; j++) {
+ if (Gpci_uart_info[j].type == brd->chip_flag) {
+ brd->ports[i].max_baud =
+ Gpci_uart_info[j].max_baud;
+
+ /* exception....CP-102 */
+ if (board_type == MXSER_BOARD_CP102)
+ brd->ports[i].max_baud = 921600;
+ break;
}
}
- (void)inb(port);
- value = 0;
- for (k = 0, j = 0x8000; k < 16; k++, j >>= 1) {
- outb(CHIP_CS, port);
- outb(CHIP_CS | CHIP_SK, port);
- if (inb(port) & CHIP_DI)
- value |= j;
+ }
+
+ if (brd->chip_flag == MOXA_MUST_MU860_HWID) {
+ for (i = 0; i < brd->nports; i++) {
+ if (i < 4)
+ brd->ports[i].opmode_ioaddr = ioaddress + 4;
+ else
+ brd->ports[i].opmode_ioaddr = ioaddress + 0x0c;
}
- regs[i] = value;
- outb(0, port);
+ outb(0, ioaddress + 4); /* default set to RS232 mode */
+ outb(0, ioaddress + 0x0c); /* default set to RS232 mode */
}
- mxser_normal_mode(port);
- return id;
+
+ for (i = 0; i < brd->nports; i++) {
+ brd->vector_mask |= (1 << i);
+ brd->ports[i].baud_base = 921600;
+ }
+ return 0;
+err_relio:
+ pci_release_region(pdev, 2);
+err:
+ return retval;
}

-static int mxser_program_mode(int port)
+static int __init mxser_module_init(void)
{
- int id, i, j, n;
- /* unsigned long flags; */
+ struct pci_dev *pdev = NULL;
+ struct mxser_board *brd;
+ unsigned int i, m;
+ int retval, b, n;

- spin_lock(&gm_lock);
- outb(0, port);
- outb(0, port);
- outb(0, port);
- (void)inb(port);
- (void)inb(port);
- outb(0, port);
- (void)inb(port);
- /* restore_flags(flags); */
- spin_unlock(&gm_lock);
+ pr_debug("Loading module mxser ...\n");

- id = inb(port + 1) & 0x1F;
- if ((id != C168_ASIC_ID) &&
- (id != C104_ASIC_ID) &&
- (id != C102_ASIC_ID) &&
- (id != CI132_ASIC_ID) &&
- (id != CI134_ASIC_ID) &&
- (id != CI104J_ASIC_ID))
- return -1;
- for (i = 0, j = 0; i < 4; i++) {
- n = inb(port + 2);
- if (n == 'M') {
- j = 1;
- } else if ((j == 1) && (n == 1)) {
- j = 2;
- break;
- } else
- j = 0;
+ mxvar_sdriver = alloc_tty_driver(MXSER_PORTS + 1);
+ if (!mxvar_sdriver)
+ return -ENOMEM;
+ spin_lock_init(&gm_lock);
+
+ for (i = 0; i < MXSER_BOARDS; i++)
+ mxser_boards[i].board_type = -1;
+
+ printk(KERN_INFO "MOXA Smartio/Industio family driver version %s\n",
+ MXSER_VERSION);
+
+ /* Initialize the tty_driver structure */
+ mxvar_sdriver->magic = TTY_DRIVER_MAGIC;
+ mxvar_sdriver->name = "ttyM";
+ mxvar_sdriver->major = ttymajor;
+ mxvar_sdriver->minor_start = 0;
+ mxvar_sdriver->num = MXSER_PORTS + 1;
+ mxvar_sdriver->type = TTY_DRIVER_TYPE_SERIAL;
+ mxvar_sdriver->subtype = SERIAL_TYPE_NORMAL;
+ mxvar_sdriver->init_termios = tty_std_termios;
+ mxvar_sdriver->init_termios.c_cflag = B9600|CS8|CREAD|HUPCL|CLOCAL;
+ mxvar_sdriver->flags = TTY_DRIVER_REAL_RAW;
+ tty_set_operations(mxvar_sdriver, &mxser_ops);
+ mxvar_sdriver->ttys = mxvar_tty;
+ mxvar_sdriver->termios = mxvar_termios;
+ mxvar_sdriver->termios_locked = mxvar_termios_locked;
+
+ mxvar_diagflag = 0;
+
+ m = 0;
+ /* Start finding ISA boards here */
+ for (b = 0; b < MXSER_BOARDS && m < MXSER_BOARDS; b++) {
+ int cap;
+
+ if (!(cap = mxserBoardCAP[b]))
+ continue;
+
+ brd = &mxser_boards[m];
+ retval = mxser_get_ISA_conf(cap, brd);
+
+ if (retval != 0)
+ printk(KERN_INFO "Found MOXA %s board (CAP=0x%x)\n",
+ mxser_brdname[brd->board_type - 1], ioaddr[b]);
+
+ if (retval <= 0) {
+ if (retval == MXSER_ERR_IRQ)
+ printk(KERN_ERR "Invalid interrupt number, "
+ "board not configured\n");
+ else if (retval == MXSER_ERR_IRQ_CONFLIT)
+ printk(KERN_ERR "Invalid interrupt number, "
+ "board not configured\n");
+ else if (retval == MXSER_ERR_VECTOR)
+ printk(KERN_ERR "Invalid interrupt vector, "
+ "board not configured\n");
+ else if (retval == MXSER_ERR_IOADDR)
+ printk(KERN_ERR "Invalid I/O address, "
+ "board not configured\n");
+
+ continue;
+ }
+
+ brd->pdev = NULL;
+
+ /* mxser_initbrd will hook ISR. */
+ if (mxser_initbrd(brd) < 0)
+ continue;
+
+ m++;
}
- if (j != 2)
- id = -2;
- return id;
+
+ /* Start finding ISA boards from module arg */
+ for (b = 0; b < MXSER_BOARDS && m < MXSER_BOARDS; b++) {
+ unsigned long cap;
+
+ if (!(cap = ioaddr[b]))
+ continue;
+
+ brd = &mxser_boards[m];
+ retval = mxser_get_ISA_conf(cap, &mxser_boards[m]);
+
+ if (retval != 0)
+ printk(KERN_INFO "Found MOXA %s board (CAP=0x%x)\n",
+ mxser_brdname[brd->board_type - 1], ioaddr[b]);
+
+ if (retval <= 0) {
+ if (retval == MXSER_ERR_IRQ)
+ printk(KERN_ERR "Invalid interrupt number, "
+ "board not configured\n");
+ else if (retval == MXSER_ERR_IRQ_CONFLIT)
+ printk(KERN_ERR "Invalid interrupt number, "
+ "board not configured\n");
+ else if (retval == MXSER_ERR_VECTOR)
+ printk(KERN_ERR "Invalid interrupt vector, "
+ "board not configured\n");
+ else if (retval == MXSER_ERR_IOADDR)
+ printk(KERN_ERR "Invalid I/O address, "
+ "board not configured\n");
+
+ continue;
+ }
+
+ brd->pdev = NULL;
+ /* mxser_initbrd will hook ISR. */
+ if (mxser_initbrd(brd) < 0)
+ continue;
+
+ m++;
+ }
+
+ /* start finding PCI board here */
+ n = ARRAY_SIZE(mxser_pcibrds) - 1;
+ b = 0;
+ while (b < n) {
+ pdev = pci_get_device(mxser_pcibrds[b].vendor,
+ mxser_pcibrds[b].device, pdev);
+ if (pdev == NULL) {
+ b++;
+ continue;
+ }
+ printk(KERN_INFO "Found MOXA %s board(BusNo=%d,DevNo=%d)\n",
+ mxser_brdname[(int) (mxser_pcibrds[b].driver_data) - 1],
+ pdev->bus->number, PCI_SLOT(pdev->devfn));
+ if (m >= MXSER_BOARDS)
+ printk(KERN_ERR
+ "Too many Smartio/Industio family boards find "
+ "(maximum %d), board not configured\n",
+ MXSER_BOARDS);
+ else {
+ if (pci_enable_device(pdev)) {
+ printk(KERN_ERR "Moxa SmartI/O PCI enable "
+ "fail !\n");
+ continue;
+ }
+ brd = &mxser_boards[m];
+ brd->pdev = pdev;
+ retval = mxser_get_PCI_conf(
+ (int)mxser_pcibrds[b].driver_data,
+ brd, pdev);
+ if (retval < 0) {
+ if (retval == MXSER_ERR_IRQ)
+ printk(KERN_ERR
+ "Invalid interrupt number, "
+ "board not configured\n");
+ else if (retval == MXSER_ERR_IRQ_CONFLIT)
+ printk(KERN_ERR
+ "Invalid interrupt number, "
+ "board not configured\n");
+ else if (retval == MXSER_ERR_VECTOR)
+ printk(KERN_ERR
+ "Invalid interrupt vector, "
+ "board not configured\n");
+ else if (retval == MXSER_ERR_IOADDR)
+ printk(KERN_ERR
+ "Invalid I/O address, "
+ "board not configured\n");
+ continue;
+ }
+ /* mxser_initbrd will hook ISR. */
+ if (mxser_initbrd(brd) < 0)
+ continue;
+ m++;
+ /* Keep an extra reference if we succeeded. It will
+ be returned at unload time */
+ pci_dev_get(pdev);
+ }
+ }
+
+ retval = tty_register_driver(mxvar_sdriver);
+ if (retval) {
+ printk(KERN_ERR "Couldn't install MOXA Smartio/Industio family"
+ " driver !\n");
+ put_tty_driver(mxvar_sdriver);
+
+ for (i = 0; i < MXSER_BOARDS; i++) {
+ if (mxser_boards[i].board_type == -1)
+ continue;
+ else {
+ free_irq(mxser_boards[i].irq, &mxser_boards[i]);
+ /* todo: release io, vector */
+ }
+ }
+ return retval;
+ }
+
+ pr_debug("Done.\n");
+
+ return retval;
}

-static void mxser_normal_mode(int port)
+static void __exit mxser_module_exit(void)
{
- int i, n;
+ int i, err;

- outb(0xA5, port + 1);
- outb(0x80, port + 3);
- outb(12, port + 0); /* 9600 bps */
- outb(0, port + 1);
- outb(0x03, port + 3); /* 8 data bits */
- outb(0x13, port + 4); /* loop back mode */
- for (i = 0; i < 16; i++) {
- n = inb(port + 5);
- if ((n & 0x61) == 0x60)
- break;
- if ((n & 1) == 1)
- (void)inb(port);
+ pr_debug("Unloading module mxser ...\n");
+
+ err = tty_unregister_driver(mxvar_sdriver);
+ if (!err)
+ put_tty_driver(mxvar_sdriver);
+ else
+ printk(KERN_ERR "Couldn't unregister MOXA Smartio/Industio family serial driver\n");
+
+ for (i = 0; i < MXSER_BOARDS; i++) {
+ struct pci_dev *pdev;
+
+ if (mxser_boards[i].board_type == -1)
+ continue;
+ else {
+ pdev = mxser_boards[i].pdev;
+ free_irq(mxser_boards[i].irq, &mxser_boards[i]);
+ if (pdev != NULL) { /* PCI */
+ pci_release_region(pdev, 2);
+ pci_release_region(pdev, 3);
+ pci_dev_put(pdev);
+ } else {
+ release_region(mxser_boards[i].ports[0].ioaddr, 8 * mxser_boards[i].nports);
+ release_region(mxser_boards[i].vector, 1);
+ }
+ }
}
- outb(0x00, port + 4);
+ pr_debug("Done.\n");
}

module_init(mxser_module_init);
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
\
 
 \ /
  Last update: 2006-10-04 00:09    [W:0.236 / U:0.084 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site