Messages in this thread | | | Date | Sat, 14 Aug 2004 19:00:16 -0400 (EDT) | Subject | Symbios hangs on boot since 2.6.6 | From | "George Glover" <> |
| |
Hello,
I believe this error has been reported once before and I was not able to track down a response.
http://marc.theaimsgroup.com/?l=linux-kernel&m=108332206118640&w=2
Starting with (linux-2.6.6) sym-2.1.18j I see: (written + re-typed)
... sym0: <1010-33> rev 0x1 at pci 0000:00:08.0 irq 169 sym0: Symbios NVRAM, ID 7, Fast-80, LVD, parity checking sym0: open drain IRQ line driver, using on-chip SRAM sym0: using LOAD/STORE-based firmware. sym0: handling phase mismatch from SCRIPTS. sym0: SCSI BUS has been reset. scsi0 : sym-2.1.18j Vendor: QUANTUM Model: ATLAS10KII_36SCA Rev: QK6C Type: Direct-Access ANSI SCSI revision: 03 sym0:1:0: tagged command queuing enabled, command queue depth 16. scsi(0:0:1:0): Beginning Domain Validation sym0:1: wide asynchronous. sym0:1:0: ABORT operation started. sym0:1:0: ABORT operation timed-out. sym0:1:0: DEVICE RESET operation started. sym0:1:0: DEVICE RESET operation timed-out. sym0:1:0: BUS RESET operation started. sym0: SCSI BUS reset detected. sym0: SCSI BUS has been reset. sym0: SCSI BUS operation completed. ... It repeats and ends with a HOST RESET operation and the system stops.
A "normal" boot sequence from linux-2.6.5 is: ... sym0: <1010-33> rev 0x1 at pci 0000:00:08.0 irq 169 sym0: Symbios NVRAM, ID 7, Fast-80, LVD, parity checking sym0: open drain IRQ line driver, using on-chip SRAM sym0: using LOAD/STORE-based firmware. sym0: handling phase mismatch from SCRIPTS. sym0: SCSI BUS has been reset. scsi0 : sym-2.1.18i Vendor: QUANTUM Model: ATLAS10KII_36SCA Rev: QK6C Type: Direct-Access ANSI SCSI revision: 03 sym0:1:0: tagged command queuing enabled, command queue depth 16. Vendor: QUANTUM Model: ATLAS10KII_36SCA Rev: QK6C Type: Direct-Access ANSI SCSI revision: 03 sym0:2:0: tagged command queuing enabled, command queue depth 16. Vendor: QUANTUM Model: ATLAS10KII_36SCA Rev: QK6C Type: Direct-Access ANSI SCSI revision: 03 sym0:4:0: tagged command queuing enabled, command queue depth 16. Vendor: QUANTUM Model: ATLAS10KII_36SCA Rev: QK6C Type: Direct-Access ANSI SCSI revision: 03 sym0:8:0: tagged command queuing enabled, command queue depth 16. sym1: <1010-33> rev 0x1 at pci 0000:00:08.1 irq 177 sym1: Symbios NVRAM, ID 7, Fast-80, SE, parity checking sym1: open drain IRQ line driver, using on-chip SRAM sym1: using LOAD/STORE-based firmware. sym1: handling phase mismatch from SCRIPTS. sym1: SCSI BUS has been reset. scsi1 : sym-2.1.18i Vendor: QUANTUM Model: XP34550W Rev: LXY4 Type: Direct-Access ANSI SCSI revision: 02 sym1:0:0: tagged command queuing enabled, command queue depth 16. Vendor: PIONEER Model: DVD-ROM DVD-305 Rev: 1.03 Type: CD-ROM ANSI SCSI revision: 02 sym0:1: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 62)
The relevant adapter(s) is:
00:08.0 SCSI storage controller: LSI Logic / Symbios Logic 53c1010 Ultra3 SCSI Ad apter (rev 01) Subsystem: LSI Logic / Symbios Logic: Unknown device 1040 Flags: bus master, medium devsel, latency 72, IRQ 169 I/O ports at c000 [size=256] Memory at f9006000 (64-bit, non-prefetchable) [size=1K] Memory at f9002000 (64-bit, non-prefetchable) [size=8K] Expansion ROM at <unassigned> [disabled] [size=128K] Capabilities: [40] Power Management version 2
00:08.1 SCSI storage controller: LSI Logic / Symbios Logic 53c1010 Ultra3 SCSI Ad apter (rev 01) Subsystem: LSI Logic / Symbios Logic: Unknown device 1040 Flags: bus master, medium devsel, latency 72, IRQ 177 I/O ports at c400 [size=256] Memory at f9004000 (64-bit, non-prefetchable) [size=1K] Memory at f9000000 (64-bit, non-prefetchable) [size=8K] Expansion ROM at <unassigned> [disabled] [size=128K] Capabilities: [40] Power Management version 2
Thank's in advance to anyone with advice!
George
- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
| |