Messages in this thread | | | Date | Sat, 10 Jan 2004 08:00:08 -0800 | From | "Martin J. Bligh" <> | Subject | [Bug 1826] New: Hang under medium network traffic (unexpected IRQ trap at vector c1 & NETDEV WATCHDOG: eth0: transmit timed out) |
| |
http://bugme.osdl.org/show_bug.cgi?id=1826
Summary: Hang under medium network traffic (unexpected IRQ trap at vector c1 & NETDEV WATCHDOG: eth0: transmit timed out) Kernel Version: 2.6.1-gentoo Status: NEW Severity: high Owner: jgarzik@pobox.com Submitter: frederic.bages@laposte.net
Distribution: Gentoo Linux Hardware Environment: PC, AMD Athlon(tm) XP 1500+, Net card 8139 Software Environment: Gentoo Linux 1.4
Problem Description: Under medium network traffic the who computer hang. The only remaining working piece is the mouse pointer. X is frozen, ping and SSH don't work. This happened more than once (with previous kernel version 2.6.0-testX). I were transfering 2Mo/s of large files between to computers.
Steps to reproduce: Not easily reproducable.
Kernel log : ============ Jan 10 11:00:06 [kernel] Pin 2-19 already programmed Jan 10 11:00:06 [kernel] Pin 2-17 already programmed Jan 10 11:00:06 [kernel] VP_IDE: not 100% native mode: will probe irqs later Jan 10 11:00:06 [kernel] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx Jan 10 11:00:07 [kernel] ehci_hcd: block sizes: qh 128 qtd 96 itd 128 sitd 64 Jan 10 11:00:07 [kernel] ehci_hcd 0000:02:08.2: EHCI Host Controller Jan 10 11:00:07 [kernel] ehci_hcd 0000:02:08.2: reset hcs_params 0x2395 dbg=0 cc=2 pcc=3 ports=5 Jan 10 11:00:07 [kernel] ehci_hcd 0000:02:08.2: reset portroute 1 0 1 0 0 Jan 10 11:00:07 [kernel] ehci_hcd 0000:02:08.2: reset hcc_params 0002 thresh 0 uframes 256/512/1024 Jan 10 11:00:07 [kernel] ehci_hcd 0000:02:08.2: irq 16, pci mem f89e4f00 Jan 10 11:00:07 [kernel] ehci_hcd 0000:02:08.2: new USB bus registered, assigned bus number 3 Jan 10 11:00:07 [kernel] ehci_hcd 0000:02:08.2: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT Jan 10 11:00:07 [kernel] ehci_hcd 0000:02:08.2: init command 010009 (park)=0 ithresh=1 period=256 RUN Jan 10 11:00:07 [kernel] ehci_hcd 0000:02:08.2: USB 2.0 enabled, EHCI 0.95, driver 2003-Jun-13 Jan 10 11:00:07 [kernel] ehci_hcd 0000:02:08.2: root hub device address 1 Jan 10 11:00:07 [kernel] usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1 Jan 10 11:00:07 [kernel] drivers/usb/core/message.c: USB device number 1 default language ID 0x409 Jan 10 11:00:07 [kernel] usb usb3: Product: EHCI Host Controller Jan 10 11:00:07 [kernel] usb usb3: Manufacturer: Linux 2.6.1-gentoo ehci_hcd Jan 10 11:00:07 [kernel] usb usb3: SerialNumber: 0000:02:08.2 Jan 10 11:00:07 [kernel] drivers/usb/core/usb.c: usb_hotplug Jan 10 11:00:07 [kernel] usb usb3: registering 3-0:1.0 (config #1, interface 0) Jan 10 11:00:07 [kernel] drivers/usb/core/usb.c: usb_hotplug Jan 10 11:00:07 [kernel] hub 3-0:1.0: usb_probe_interface Jan 10 11:00:07 [kernel] hub 3-0:1.0: usb_probe_interface - got id Jan 10 11:00:07 [kernel] hub 3-0:1.0: USB hub found Jan 10 11:00:07 [kernel] hub 3-0:1.0: 5 ports detected Jan 10 11:00:07 [kernel] hub 3-0:1.0: standalone hub Jan 10 11:00:07 [kernel] hub 3-0:1.0: individual port power switching Jan 10 11:00:07 [kernel] hub 3-0:1.0: individual port over-current protection Jan 10 11:00:07 [kernel] hub 3-0:1.0: Single TT Jan 10 11:00:07 [kernel] hub 3-0:1.0: TT requires at most 8 FS bit times Jan 10 11:00:07 [kernel] hub 3-0:1.0: Port indicators are not supported Jan 10 11:00:07 [kernel] hub 3-0:1.0: power on to power good time: 0ms Jan 10 11:00:07 [kernel] hub 3-0:1.0: hub controller current requirement: 0mA Jan 10 11:00:07 [kernel] hub 3-0:1.0: local power source is good Jan 10 11:00:07 [kernel] hub 3-0:1.0: no over-current condition exists Jan 10 11:00:07 [kernel] hub 3-0:1.0: enabling power on all ports Jan 10 11:00:07 [kernel] ohci_hcd: 2003 Oct 13 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) Jan 10 11:00:07 [kernel] ohci_hcd 0000:02:08.0: irq 18, pci mem f89e6000 Jan 10 11:00:07 [kernel] ohci_hcd 0000:02:08.0: new USB bus registered, assigned bus number 4 Jan 10 11:00:08 [kernel] ohci_hcd 0000:02:08.0: root hub device address 1 Jan 10 11:00:08 [kernel] usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1 Jan 10 11:00:08 [kernel] drivers/usb/core/message.c: USB device number 1 default language ID 0x409 Jan 10 11:00:08 [kernel] usb usb4: Product: OHCI Host Controller Jan 10 11:00:08 [kernel] usb usb4: Manufacturer: Linux 2.6.1-gentoo ohci_hcd Jan 10 11:00:08 [kernel] usb usb4: SerialNumber: 0000:02:08.0 Jan 10 11:00:08 [kernel] drivers/usb/core/usb.c: usb_hotplug Jan 10 11:00:08 [kernel] usb usb4: registering 4-0:1.0 (config #1, interface 0) Jan 10 11:00:08 [kernel] drivers/usb/core/usb.c: usb_hotplug Jan 10 11:00:08 [kernel] hub 4-0:1.0: usb_probe_interface Jan 10 11:00:08 [kernel] hub 4-0:1.0: usb_probe_interface - got id Jan 10 11:00:08 [kernel] hub 4-0:1.0: USB hub found Jan 10 11:00:08 [kernel] hub 4-0:1.0: 3 ports detected Jan 10 11:00:08 [kernel] hub 4-0:1.0: standalone hub Jan 10 11:00:08 [kernel] hub 4-0:1.0: ganged power switching Jan 10 11:00:08 [kernel] hub 4-0:1.0: global over-current protection Jan 10 11:00:08 [kernel] hub 4-0:1.0: Port indicators are not supported Jan 10 11:00:08 [kernel] hub 4-0:1.0: power on to power good time: 510ms Jan 10 11:00:08 [kernel] hub 4-0:1.0: hub controller current requirement: 0mA Jan 10 11:00:08 [kernel] hub 4-0:1.0: local power source is good Jan 10 11:00:08 [kernel] hub 4-0:1.0: no over-current condition exists Jan 10 11:00:08 [kernel] hub 4-0:1.0: enabling power on all ports Jan 10 11:00:08 [kernel] ohci_hcd 0000:02:08.0: created debug files Jan 10 11:00:08 [kernel] ohci_hcd 0000:02:08.0: OHCI controller state Jan 10 11:00:08 [kernel] ohci_hcd 0000:02:08.0: OHCI 1.0, with legacy support registers Jan 10 11:00:08 [kernel] ohci_hcd 0000:02:08.0: control 0x08f HCFS=operational IE PLE CBSR=3 Jan 10 11:00:08 [kernel] ohci_hcd 0000:02:08.0: cmdstatus 0x00000 SOC=0 Jan 10 11:00:08 [kernel] ohci_hcd 0000:02:08.0: intrstatus 0x00000004 SF Jan 10 11:00:08 [kernel] ohci_hcd 0000:02:08.0: intrenable 0x80000012 MIE UE WDH Jan 10 11:00:08 [kernel] ohci_hcd 0000:02:08.0: hcca frame #0474 Jan 10 11:00:08 [kernel] ohci_hcd 0000:02:08.0: roothub.a ff000203 POTPGT=255 NPS NDP=3 Jan 10 11:00:08 [kernel] ohci_hcd 0000:02:08.0: roothub.b 00000000 PPCM=0000 DR=0000 Jan 10 11:00:08 [kernel] ohci_hcd 0000:02:08.0: roothub.status 00000000 Jan 10 11:00:08 [kernel] ohci_hcd 0000:02:08.0: roothub.portstatus [0] 0x00000100 PPS Jan 10 11:00:08 [kernel] ohci_hcd 0000:02:08.0: roothub.portstatus [1] 0x00000100 PPS Jan 10 11:00:08 [kernel] ohci_hcd 0000:02:08.0: roothub.portstatus [2] 0x00000100 PPS Jan 10 11:00:08 [kernel] ohci_hcd 0000:02:08.1: OHCI Host Controller Jan 10 11:00:08 [kernel] ohci_hcd 0000:02:08.1: reset, control = 0x0 Jan 10 11:00:08 [kernel] ohci_hcd 0000:02:08.1: irq 19, pci mem f89f7000 Jan 10 11:00:08 [kernel] ohci_hcd 0000:02:08.1: new USB bus registered, assigned bus number 5 Jan 10 11:00:09 [kernel] ohci_hcd 0000:02:08.1: root hub device address 1 Jan 10 11:00:09 [kernel] usb usb5: new device strings: Mfr=3, Product=2, SerialNumber=1 Jan 10 11:00:09 [kernel] drivers/usb/core/message.c: USB device number 1 default language ID 0x409 Jan 10 11:00:09 [kernel] usb usb5: Product: OHCI Host Controller Jan 10 11:00:09 [kernel] usb usb5: Manufacturer: Linux 2.6.1-gentoo ohci_hcd Jan 10 11:00:09 [kernel] usb usb5: SerialNumber: 0000:02:08.1 Jan 10 11:00:09 [kernel] drivers/usb/core/usb.c: usb_hotplug Jan 10 11:00:09 [kernel] usb usb5: registering 5-0:1.0 (config #1, interface 0) Jan 10 11:00:09 [kernel] drivers/usb/core/usb.c: usb_hotplug Jan 10 11:00:09 [kernel] hub 5-0:1.0: usb_probe_interface Jan 10 11:00:09 [kernel] hub 5-0:1.0: usb_probe_interface - got id Jan 10 11:00:09 [kernel] hub 5-0:1.0: USB hub found Jan 10 11:00:09 [kernel] hub 5-0:1.0: 2 ports detected Jan 10 11:00:09 [kernel] hub 5-0:1.0: standalone hub Jan 10 11:00:09 [kernel] hub 5-0:1.0: ganged power switching Jan 10 11:00:09 [kernel] hub 5-0:1.0: global over-current protection Jan 10 11:00:09 [kernel] hub 5-0:1.0: Port indicators are not supported Jan 10 11:00:09 [kernel] hub 5-0:1.0: power on to power good time: 510ms Jan 10 11:00:09 [kernel] hub 5-0:1.0: hub controller current requirement: 0mA Jan 10 11:00:09 [kernel] hub 5-0:1.0: local power source is good Jan 10 11:00:09 [kernel] hub 5-0:1.0: no over-current condition exists Jan 10 11:00:09 [kernel] hub 5-0:1.0: enabling power on all ports Jan 10 11:00:09 [kernel] ohci_hcd 0000:02:08.1: created debug files Jan 10 11:00:09 [kernel] ohci_hcd 0000:02:08.1: OHCI controller state Jan 10 11:00:09 [kernel] ohci_hcd 0000:02:08.1: OHCI 1.0, with legacy support registers Jan 10 11:00:09 [kernel] ohci_hcd 0000:02:08.1: control 0x08f HCFS=operational IE PLE CBSR=3 Jan 10 11:00:09 [kernel] ohci_hcd 0000:02:08.1: cmdstatus 0x00000 SOC=0 Jan 10 11:00:09 [kernel] ohci_hcd 0000:02:08.1: intrstatus 0x00000004 SF Jan 10 11:00:09 [kernel] ohci_hcd 0000:02:08.1: intrenable 0x80000012 MIE UE WDH Jan 10 11:00:09 [kernel] ohci_hcd 0000:02:08.1: hcca frame #043f Jan 10 11:00:09 [kernel] ohci_hcd 0000:02:08.1: roothub.a ff000202 POTPGT=255 NPS NDP=2 Jan 10 11:00:09 [kernel] ohci_hcd 0000:02:08.1: roothub.b 00000000 PPCM=0000 DR=0000 Jan 10 11:00:09 [kernel] ohci_hcd 0000:02:08.1: roothub.status 00000000 Jan 10 11:00:09 [kernel] ohci_hcd 0000:02:08.1: roothub.portstatus [0] 0x00000100 PPS Jan 10 11:00:09 [kernel] ohci_hcd 0000:02:08.1: roothub.portstatus [1] 0x00000100 PPS Jan 10 11:00:09 [kernel] 8139cp: 10/100 PCI Ethernet driver v1.1 (Aug 30, 2003) Jan 10 11:04:50 [kernel] Pin 2-19 already programmed Jan 10 11:04:50 [kernel] Pin 2-17 already programmed Jan 10 11:04:51 [kernel] ehci_hcd: block sizes: qh 128 qtd 96 itd 128 sitd 64 Jan 10 11:04:51 [kernel] ehci_hcd 0000:02:08.2: EHCI Host Controller Jan 10 11:04:51 [kernel] ehci_hcd 0000:02:08.2: reset hcs_params 0x2395 dbg=0 cc=2 pcc=3 ports=5 Jan 10 11:04:51 [kernel] usb usb3: registering 3-0:1.0 (config #1, interface 0) Jan 10 11:04:51 [kernel] drivers/usb/core/usb.c: usb_hotplug Jan 10 11:04:51 [kernel] hub 3-0:1.0: usb_probe_interface Jan 10 11:04:51 [kernel] hub 3-0:1.0: usb_probe_interface - got id Jan 10 11:04:51 [kernel] hub 3-0:1.0: USB hub found Jan 10 11:04:51 [kernel] hub 3-0:1.0: 5 ports detected Jan 10 11:04:51 [kernel] hub 3-0:1.0: standalone hub Jan 10 11:04:51 [kernel] hub 3-0:1.0: individual port power switching Jan 10 11:04:51 [kernel] hub 3-0:1.0: individual port over-current protection Jan 10 11:04:51 [kernel] hub 3-0:1.0: Single TT Jan 10 11:04:51 [kernel] hub 3-0:1.0: TT requires at most 8 FS bit times Jan 10 11:04:51 [kernel] hub 3-0:1.0: Port indicators are not supported Jan 10 11:04:51 [kernel] hub 3-0:1.0: power on to power good time: 0ms Jan 10 11:04:51 [kernel] hub 3-0:1.0: hub controller current requirement: 0mA Jan 10 11:04:51 [kernel] hub 3-0:1.0: local power source is good Jan 10 11:04:51 [kernel] hub 3-0:1.0: no over-current condition exists Jan 10 11:04:51 [kernel] hub 3-0:1.0: enabling power on all ports Jan 10 11:04:51 [kernel] ohci_hcd: 2003 Oct 13 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) Jan 10 11:04:51 [kernel] ohci_hcd 0000:02:08.0: irq 18, pci mem f89e6000 Jan 10 11:04:51 [kernel] ohci_hcd 0000:02:08.0: new USB bus registered, assigned bus number 4 Jan 10 11:04:52 [kernel] ohci_hcd 0000:02:08.0: root hub device address 1 Jan 10 11:04:52 [kernel] usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1 Jan 10 11:04:52 [kernel] drivers/usb/core/message.c: USB device number 1 default language ID 0x409 Jan 10 11:04:52 [kernel] usb usb4: Product: OHCI Host Controller Jan 10 11:04:52 [kernel] usb usb4: Manufacturer: Linux 2.6.1-gentoo ohci_hcd Jan 10 11:04:52 [kernel] usb usb4: SerialNumber: 0000:02:08.0 Jan 10 11:04:52 [kernel] drivers/usb/core/usb.c: usb_hotplug Jan 10 11:04:52 [kernel] usb usb4: registering 4-0:1.0 (config #1, interface 0) Jan 10 11:04:52 [kernel] drivers/usb/core/usb.c: usb_hotplug Jan 10 11:04:52 [kernel] hub 4-0:1.0: usb_probe_interface Jan 10 11:04:52 [kernel] hub 4-0:1.0: usb_probe_interface - got id Jan 10 11:04:52 [kernel] hub 4-0:1.0: USB hub found Jan 10 11:04:52 [kernel] hub 4-0:1.0: 3 ports detected Jan 10 11:04:52 [kernel] hub 4-0:1.0: standalone hub Jan 10 11:04:52 [kernel] hub 4-0:1.0: ganged power switching Jan 10 11:04:52 [kernel] hub 4-0:1.0: global over-current protection Jan 10 11:04:52 [kernel] hub 4-0:1.0: Port indicators are not supported Jan 10 11:04:52 [kernel] hub 4-0:1.0: power on to power good time: 510ms Jan 10 11:04:52 [kernel] hub 4-0:1.0: hub controller current requirement: 0mA Jan 10 11:04:52 [kernel] hub 4-0:1.0: local power source is good Jan 10 11:04:52 [kernel] hub 4-0:1.0: no over-current condition exists Jan 10 11:04:52 [kernel] hub 4-0:1.0: enabling power on all ports Jan 10 11:04:52 [kernel] ohci_hcd 0000:02:08.0: created debug files Jan 10 11:04:52 [kernel] ohci_hcd 0000:02:08.0: OHCI controller state Jan 10 11:04:52 [kernel] ohci_hcd 0000:02:08.0: OHCI 1.0, with legacy support registers Jan 10 11:04:52 [kernel] ohci_hcd 0000:02:08.0: control 0x08f HCFS=operational IE PLE CBSR=3 Jan 10 11:04:52 [kernel] ohci_hcd 0000:02:08.0: cmdstatus 0x00000 SOC=0 Jan 10 11:04:52 [kernel] ohci_hcd 0000:02:08.0: intrstatus 0x00000004 SF Jan 10 11:04:52 [kernel] ohci_hcd 0000:02:08.0: intrenable 0x80000012 MIE UE WDH Jan 10 11:04:52 [kernel] ohci_hcd 0000:02:08.0: hcca frame #0474 Jan 10 11:04:52 [kernel] ohci_hcd 0000:02:08.0: roothub.a ff000203 POTPGT=255 NPS NDP=3 Jan 10 11:04:52 [kernel] ohci_hcd 0000:02:08.0: roothub.b 00000000 PPCM=0000 DR=0000 Jan 10 11:04:52 [kernel] ohci_hcd 0000:02:08.0: roothub.status 00000000 Jan 10 11:04:52 [kernel] ohci_hcd 0000:02:08.0: roothub.portstatus [0] 0x00000100 PPS Jan 10 11:04:52 [kernel] ohci_hcd 0000:02:08.0: roothub.portstatus [1] 0x00000100 PPS Jan 10 11:04:52 [kernel] ohci_hcd 0000:02:08.0: roothub.portstatus [2] 0x00000100 PPS Jan 10 11:04:52 [kernel] ohci_hcd 0000:02:08.1: OHCI Host Controller Jan 10 11:04:52 [kernel] ohci_hcd 0000:02:08.1: reset, control = 0x0 Jan 10 11:04:52 [kernel] ohci_hcd 0000:02:08.1: irq 19, pci mem f89f7000 Jan 10 11:04:52 [kernel] ohci_hcd 0000:02:08.1: new USB bus registered, assigned bus number 5 Jan 10 11:04:53 [kernel] ohci_hcd 0000:02:08.1: root hub device address 1 Jan 10 11:04:53 [kernel] usb usb5: new device strings: Mfr=3, Product=2, SerialNumber=1 Jan 10 11:04:53 [kernel] drivers/usb/core/message.c: USB device number 1 default language ID 0x409 Jan 10 11:04:53 [kernel] usb usb5: Product: OHCI Host Controller Jan 10 11:04:53 [kernel] usb usb5: Manufacturer: Linux 2.6.1-gentoo ohci_hcd Jan 10 11:04:53 [kernel] usb usb5: SerialNumber: 0000:02:08.1 Jan 10 11:04:53 [kernel] drivers/usb/core/usb.c: usb_hotplug Jan 10 11:04:53 [kernel] usb usb5: registering 5-0:1.0 (config #1, interface 0) Jan 10 11:04:53 [kernel] drivers/usb/core/usb.c: usb_hotplug Jan 10 11:04:53 [kernel] hub 5-0:1.0: usb_probe_interface Jan 10 11:04:53 [kernel] hub 5-0:1.0: usb_probe_interface - got id Jan 10 11:04:53 [kernel] hub 5-0:1.0: USB hub found Jan 10 11:04:53 [kernel] hub 5-0:1.0: 2 ports detected Jan 10 11:04:53 [kernel] hub 5-0:1.0: standalone hub Jan 10 11:04:53 [kernel] hub 5-0:1.0: ganged power switching Jan 10 11:04:53 [kernel] hub 5-0:1.0: global over-current protection Jan 10 11:04:53 [kernel] hub 5-0:1.0: Port indicators are not supported Jan 10 11:04:53 [kernel] hub 5-0:1.0: power on to power good time: 510ms Jan 10 11:04:53 [kernel] hub 5-0:1.0: hub controller current requirement: 0mA Jan 10 11:04:53 [kernel] hub 5-0:1.0: local power source is good Jan 10 11:04:53 [kernel] hub 5-0:1.0: no over-current condition exists Jan 10 11:04:53 [kernel] hub 5-0:1.0: enabling power on all ports Jan 10 11:04:53 [kernel] ohci_hcd 0000:02:08.1: created debug files Jan 10 11:04:53 [kernel] ohci_hcd 0000:02:08.1: OHCI controller state Jan 10 11:04:53 [kernel] ohci_hcd 0000:02:08.1: OHCI 1.0, with legacy support registers Jan 10 11:04:53 [kernel] ohci_hcd 0000:02:08.1: control 0x08f HCFS=operational IE PLE CBSR=3 Jan 10 11:04:53 [kernel] ohci_hcd 0000:02:08.1: cmdstatus 0x00000 SOC=0 Jan 10 11:04:53 [kernel] ohci_hcd 0000:02:08.1: intrstatus 0x00000004 SF Jan 10 11:04:53 [kernel] ohci_hcd 0000:02:08.1: intrenable 0x80000012 MIE UE WDH Jan 10 11:04:53 [kernel] ohci_hcd 0000:02:08.1: hcca frame #043f Jan 10 11:04:53 [kernel] ohci_hcd 0000:02:08.1: roothub.a ff000202 POTPGT=255 NPS NDP=2 Jan 10 11:04:53 [kernel] ohci_hcd 0000:02:08.1: roothub.b 00000000 PPCM=0000 DR=0000 Jan 10 11:04:53 [kernel] ohci_hcd 0000:02:08.1: roothub.status 00000000 Jan 10 11:04:53 [kernel] ohci_hcd 0000:02:08.1: roothub.portstatus [0] 0x00000100 PPS Jan 10 11:04:53 [kernel] ohci_hcd 0000:02:08.1: roothub.portstatus [1] 0x00000100 PPS Jan 10 11:04:53 [kernel] 8139cp: 10/100 PCI Ethernet driver v1.1 (Aug 30, 2003) Jan 10 11:18:31 [kernel] nvidia: no version for "struct_module" found: kernel tainted. Jan 10 11:18:31 [kernel] nvidia: no version magic, tainting kernel. Jan 10 11:18:31 [kernel] nvidia: module license 'NVIDIA' taints kernel. Jan 10 11:18:31 [kernel] 0: nvidia: loading NVIDIA Linux x86 nvidia.o Kernel Module 1.0-4496 Wed Jul 16 19:03:09 PDT 2003 Jan 10 11:18:32 [kernel] Debug: sleeping function called from invalid context at mm/slab.c:1856 - Last output repeated twice - Jan 10 11:18:34 [kernel] agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0. Jan 10 11:18:35 [kernel] atkbd.c: Unknown key released (translated set 2, code 0x7a on isa0060/serio0). - Last output repeated twice - Jan 10 11:19:08 [kernel] APIC error on CPU0: 00(02) Jan 10 11:27:07 [kernel] APIC error on CPU0: 02(08) Jan 10 11:29:38 [kernel] APIC error on CPU0: 08(08) Jan 10 11:30:06 [kernel] APIC error on CPU0: 08(02) Jan 10 11:33:57 [kernel] APIC error on CPU0: 02(08) Jan 10 11:44:29 [kernel] irq 11: nobody cared! Jan 10 11:45:31 [kernel] APIC error on CPU0: 08(02) Jan 10 11:46:09 [kernel] APIC error on CPU0: 02(02) - Last output repeated twice - Jan 10 11:47:04 [kernel] APIC error on CPU0: 02(08) Jan 10 11:50:30 [kernel] APIC error on CPU0: 08(02) Jan 10 11:50:40 [kernel] APIC error on CPU0: 02(02) - Last output repeated 7 times - Jan 10 11:56:58 [kernel] APIC error on CPU0: 02(08) Jan 10 11:57:00 [kernel] APIC error on CPU0: 08(02) Jan 10 11:57:04 [kernel] APIC error on CPU0: 02(02) Jan 10 11:57:07 [kernel] APIC error on CPU0: 02(08) Jan 10 11:57:42 [kernel] APIC error on CPU0: 08(02) Jan 10 11:57:54 [kernel] APIC error on CPU0: 02(02) - Last output repeated 7 times - Jan 10 11:59:39 [kernel] APIC error on CPU0: 02(08) Jan 10 11:59:49 [kernel] APIC error on CPU0: 08(02) Jan 10 11:59:59 [kernel] APIC error on CPU0: 02(02) Jan 10 12:00:00 [kernel] APIC error on CPU0: 02(08) Jan 10 12:00:09 [kernel] APIC error on CPU0: 08(02) Jan 10 12:00:56 [kernel] APIC error on CPU0: 02(08) Jan 10 12:01:14 [kernel] APIC error on CPU0: 08(08) - Last output repeated twice - Jan 10 12:01:42 [kernel] APIC error on CPU0: 08(02) Jan 10 12:01:54 [kernel] APIC error on CPU0: 02(02) - Last output repeated 2 times - Jan 10 12:02:59 [kernel] APIC error on CPU0: 02(08) Jan 10 12:03:02 [kernel] APIC error on CPU0: 08(02) Jan 10 12:03:02 [kernel] APIC error on CPU0: 02(02) - Last output repeated 3 times - Jan 10 12:03:22 [kernel] APIC error on CPU0: 02(08) Jan 10 12:03:38 [kernel] APIC error on CPU0: 08(02) Jan 10 12:03:42 [kernel] APIC error on CPU0: 02(08) Jan 10 12:03:59 [kernel] APIC error on CPU0: 08(02) Jan 10 12:04:04 [kernel] APIC error on CPU0: 02(08) Jan 10 12:04:12 [kernel] APIC error on CPU0: 08(02) Jan 10 12:04:15 [kernel] APIC error on CPU0: 02(02) - Last output repeated twice - Jan 10 12:05:15 [kernel] APIC error on CPU0: 02(08) Jan 10 12:06:08 [kernel] APIC error on CPU0: 08(08) Jan 10 12:06:22 [kernel] APIC error on CPU0: 08(02) Jan 10 12:06:58 [kernel] APIC error on CPU0: 02(08) Jan 10 12:07:23 [kernel] APIC error on CPU0: 08(02) Jan 10 12:07:23 [kernel] APIC error on CPU0: 02(08) Jan 10 12:07:24 [kernel] unexpected IRQ trap at vector c1 Jan 10 12:07:33 [kernel] NETDEV WATCHDOG: eth0: transmit timed out Jan 10 12:07:35 [kernel] Badness in pci_find_subsys at drivers/pci/search.c:132 - Last output repeated twice - Jan 10 12:07:43 [kernel] [<f8e0cf18>] __nvsym04875+0xf8/0x170 [nvidia] Jan 10 12:07:45 [kernel] NETDEV WATCHDOG: eth0: transmit timed out Jan 10 12:07:51 [kernel] Badness in pci_find_subsys at drivers/pci/search.c:132 Jan 10 12:07:57 [kernel] NETDEV WATCHDOG: eth0: transmit timed out Jan 10 12:07:59 [kernel] Badness in pci_find_subsys at drivers/pci/search.c:132 - Last output repeated 3 times - Jan 10 12:08:27 [kernel] NETDEV WATCHDOG: eth0: transmit timed out Jan 10 12:08:31 [kernel] Badness in pci_find_subsys at drivers/pci/search.c:132 - Last output repeated 5 times - Jan 10 12:09:15 [kernel] NETDEV WATCHDOG: eth0: transmit timed out Jan 10 12:09:19 [kernel] Badness in pci_find_subsys at drivers/pci/search.c:132 - Last output repeated 2 times - Jan 10 12:10:57 [kernel] NETDEV WATCHDOG: eth0: transmit timed out Jan 10 12:13:20 [kernel] 00 000 00 1 0 0 0 0 0 0 00 Jan 10 12:13:21 [kernel] 01 001 01 0 0 0 0 0 1 1 39 lspci : ======= 00:00.0 Host bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133] (rev 03) 00:01.0 PCI bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133 AGP] 00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 40) 00:07.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE (rev 06) 00:07.2 USB Controller: VIA Technologies, Inc. USB (rev 1a) 00:07.3 USB Controller: VIA Technologies, Inc. USB (rev 1a) 00:07.4 SMBus: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 40) 00:07.5 Multimedia audio controller: VIA Technologies, Inc. VT82C686 AC97 Audio Controller (rev 50) 00:0a.0 PCI bridge: Hint Corp HB6 Universal PCI-PCI bridge (non-transparent mode) (rev 13) 00:0c.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) 01:00.0 VGA compatible controller: nVidia Corporation NV11 [GeForce2 MX/MX 400] (rev b2) 02:08.0 USB Controller: NEC Corporation USB (rev 41) 02:08.1 USB Controller: NEC Corporation USB (rev 41) 02:08.2 USB Controller: NEC Corporation USB 2.0 (rev 02) 02:0b.0 FireWire (IEEE 1394): Texas Instruments TSB12LV26 IEEE-1394 Controller (Link) lsmod : ======= Module Size Used by nvidia 1701932 10 8139cp 19904 0 ohci_hcd 31040 0 ehci_hcd 35904 0 rtc 13288 0 ohci1394 36544 0 ieee1394 293004 1 ohci1394 usblp 13376 0 usb_storage 104208 0 uhci_hcd 33416 0 usbcore 121044 7 ohci_hcd,ehci_hcd,usblp,usb_storage,uhci_hcd 8139too 23360 0 mii 5184 2 8139cp,8139too sg 34828 0 sr_mod 16928 0 sd_mod 15584 0 scsi_mod 79844 4 usb_storage,sg,sr_mod,sd_mod
- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
| |