Messages in this thread | | | From | Julien LEMOINE <> | Subject | [2.4.21] SYM53C8XX on alpha system | Date | Sat, 21 Jun 2003 22:53:49 +0200 |
| |
Hi,
I have an scsi U160 card with 53c1010 chipset (tekram DC-390U3W) on an Alpha PCA56 (Digital AlphaPC 164SX 533 MHz). The card is correctly detected, but all U160 HD are detected as FAST-10 SCSI instead of U160. I am using "SYM53C8XX Version 2" driver, and I tryed every parameters documented in sym53c8xx_2/Documentation.txt.
Thanks.
******** dmesg ******** PCI: dev LSI Logic / Symbios Logic (formerly NCR) 53c1010 Ultra3 SCSI Adapter type 64-bit PCI: dev LSI Logic / Symbios Logic (formerly NCR) 53c1010 Ultra3 SCSI Adapter (#2) type 64-bit PCI: dev LSI Logic / Symbios Logic (formerly NCR) 53c1010 Ultra3 SCSI Adapter type 64-bit PCI: dev LSI Logic / Symbios Logic (formerly NCR) 53c1010 Ultra3 SCSI Adapter (#2) type 64-bit SMC37c669 Super I/O Controller found @ 0x3f0 [...] SCSI subsystem driver Revision: 1.00 sym.0.7.0: setting PCI_COMMAND_PARITY... sym.0.7.0: setting PCI_COMMAND_INVALIDATE. sym.0.7.1: setting PCI_COMMAND_PARITY... sym.0.7.1: setting PCI_COMMAND_INVALIDATE. sym0: <1010-33> rev 0x1 on pci bus 0 device 7 function 0 irq 26 sym0: Symbios NVRAM, ID 7, Fast-80, LVD, parity checking sym0: open drain IRQ line driver, using on-chip SRAM sym0: using LOAD/STORE-based firmware. sym0: handling phase mismatch from SCRIPTS. sym0: SCSI BUS has been reset. sym1: <1010-33> rev 0x1 on pci bus 0 device 7 function 1 irq 26 sym1: Symbios NVRAM, ID 7, Fast-80, SE, parity checking sym1: open drain IRQ line driver, using on-chip SRAM sym1: using LOAD/STORE-based firmware. sym1: handling phase mismatch from SCRIPTS. sym1: SCSI BUS has been reset. scsi0 : sym-2.1.17a scsi1 : sym-2.1.17a blk: queue fffffc000026a8f0, no I/O memory limit Vendor: COMPAQ Model: BD009735C6 Rev: B021 Type: Direct-Access ANSI SCSI revision: 02 blk: queue fffffc000026aaf0, no I/O memory limit Vendor: COMPAQ Model: BD009735C6 Rev: B021 Type: Direct-Access ANSI SCSI revision: 02 blk: queue fffffc000026acf0, no I/O memory limit Vendor: COMPAQ Model: BD009735C6 Rev: B021 Type: Direct-Access ANSI SCSI revision: 02 blk: queue fffffc000026aef0, no I/O memory limit sym0:0:0: tagged command queuing enabled, command queue depth 16. sym0:2:0: tagged command queuing enabled, command queue depth 16. sym0:4:0: tagged command queuing enabled, command queue depth 16. Attached scsi disk sda at scsi0, channel 0, id 0, lun 0 Attached scsi disk sdb at scsi0, channel 0, id 2, lun 0 Attached scsi disk sdc at scsi0, channel 0, id 4, lun 0 sym0:0: FAST-10 SCSI 10.0 MB/s ST (100.0 ns, offset 31) sda: Spinning up disk.............ready SCSI device sda: 17773524 512-byte hdwr sectors (9100 MB) sda: sda1 sda2 sda3 sym0:2: FAST-10 SCSI 10.0 MB/s ST (100.0 ns, offset 31) sdb: Spinning up disk.............ready SCSI device sdb: 17773524 512-byte hdwr sectors (9100 MB) sdb: sdb1 sym0:4: FAST-10 SCSI 10.0 MB/s ST (100.0 ns, offset 31) sdc: Spinning up disk.............ready SCSI device sdc: 17773524 512-byte hdwr sectors (9100 MB) sdc: sdc1
-- Julien LEMOINE / SpeedBlue
- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
| |