lkml.org 
[lkml]   [2002]   [Mar]   [13]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
Subject[patch] PIIX rewrite patch, pre-final
Hi!

This is a rewrite of the PIIX IDE timing driver. It should give slightly
better performance (+4% was measured), and also replaces the slc90c66
Efar Victory66 driver, because the Victory66 is mostly a PIIX clone.

It has been tested on PIIX4 only. Please anyone with a PIIX or ICH chip,
and if anyone has the Victory66 one even moreso, test this if you can.

The patch is against 2.5.6 + the patches I sent earlier, for a complete
patch against clean 2.5.6 see

http://twilight.ucw.cz/ide-via-amd-piix-timing-8-pre-final.diff

Killed code good code. :)

--
Vojtech Pavlik
SuSE Labs
diff -urN linux-2.5.6-timing/drivers/ide/Config.help linux-2.5.6-piix/drivers/ide/Config.help
--- linux-2.5.6-timing/drivers/ide/Config.help Mon Mar 11 08:46:22 2002
+++ linux-2.5.6-piix/drivers/ide/Config.help Wed Mar 13 23:37:07 2002
@@ -452,28 +452,10 @@
chipsets.

CONFIG_BLK_DEV_PIIX
- This driver adds PIO mode setting and tuning for all PIIX IDE
- controllers by Intel. Since the BIOS can sometimes improperly tune
- PIO 0-4 mode settings, this allows dynamic tuning of the chipset
- via the standard end-user tool 'hdparm'.
-
- Please read the comments at the top of <file:drivers/ide/piix.c>.
-
- If you say Y here, you should also say Y to "PIIXn Tuning support",
- below.
-
- If unsure, say N.
-
-CONFIG_PIIX_TUNING
- This driver extension adds DMA mode setting and tuning for all PIIX
- IDE controllers by Intel. Since the BIOS can sometimes improperly
- set up the device/adapter combination and speed limits, it has
- become a necessity to back/forward speed devices as needed.
-
- Case 430HX/440FX PIIX3 need speed limits to reduce UDMA to DMA mode
- 2 if the BIOS can not perform this task at initialization.
-
- If unsure, say N.
+ This driver adds explicit support for Intel PIIX and ICH chips
+ and also for the Efar Victory66 (slc90e66) chip. This allows
+ the kernel to change PIO, DMA and UDMA speeds and configure
+ the chip to optimum performance.

CONFIG_BLK_DEV_PDC202XX
Promise Ultra33 or PDC20246
@@ -523,19 +505,6 @@
available" as well.

Please read the comments at the top of <file:drivers/ide/sis5513.c>.
-
-CONFIG_BLK_DEV_SLC90E66
- This driver ensures (U)DMA support for Victroy66 SouthBridges for
- SMsC with Intel NorthBridges. This is an Ultra66 based chipset.
- The nice thing about it is that you can mix Ultra/DMA/PIO devices
- and it will handle timing cycles. Since this is an improved
- look-a-like to the PIIX4 it should be a nice addition.
-
- If you say Y here, you need to say Y to "Use DMA by default when
- available" as well.
-
- Please read the comments at the top of
- <file:drivers/ide/slc90e66.c>.

CONFIG_BLK_DEV_SL82C105
If you have a Winbond SL82c105 IDE controller, say Y here to enable
diff -urN linux-2.5.6-timing/drivers/ide/Config.in linux-2.5.6-piix/drivers/ide/Config.in
--- linux-2.5.6-timing/drivers/ide/Config.in Mon Mar 11 08:46:22 2002
+++ linux-2.5.6-piix/drivers/ide/Config.in Wed Mar 13 23:37:20 2002
@@ -67,10 +67,7 @@
dep_bool ' HPT34X chipset support' CONFIG_BLK_DEV_HPT34X $CONFIG_BLK_DEV_IDEDMA_PCI
dep_mbool ' HPT34X AUTODMA support (WIP)' CONFIG_HPT34X_AUTODMA $CONFIG_BLK_DEV_HPT34X $CONFIG_IDEDMA_PCI_WIP
dep_bool ' HPT366 chipset support' CONFIG_BLK_DEV_HPT366 $CONFIG_BLK_DEV_IDEDMA_PCI
- if [ "$CONFIG_X86" = "y" -o "$CONFIG_IA64" = "y" ]; then
- dep_mbool ' Intel PIIXn chipsets support' CONFIG_BLK_DEV_PIIX $CONFIG_BLK_DEV_IDEDMA_PCI
- dep_mbool ' PIIXn Tuning support' CONFIG_PIIX_TUNING $CONFIG_BLK_DEV_PIIX $CONFIG_IDEDMA_PCI_AUTO
- fi
+ dep_bool ' Intel PIIX, ICH and Efar Victory66 chipsets support' CONFIG_BLK_DEV_PIIX $CONFIG_BLK_DEV_IDEDMA_PCI
if [ "$CONFIG_MIPS_ITE8172" = "y" -o "$CONFIG_MIPS_IVR" = "y" ]; then
dep_mbool ' IT8172 IDE support' CONFIG_BLK_DEV_IT8172 $CONFIG_BLK_DEV_IDEDMA_PCI
dep_mbool ' IT8172 IDE Tuning support' CONFIG_IT8172_TUNING $CONFIG_BLK_DEV_IT8172 $CONFIG_IDEDMA_PCI_AUTO
@@ -83,7 +80,6 @@
dep_bool ' Special FastTrak Feature' CONFIG_PDC202XX_FORCE $CONFIG_BLK_DEV_PDC202XX
dep_bool ' ServerWorks OSB4/CSB5 chipsets support' CONFIG_BLK_DEV_SVWKS $CONFIG_BLK_DEV_IDEDMA_PCI $CONFIG_X86
dep_bool ' SiS5513 chipset support' CONFIG_BLK_DEV_SIS5513 $CONFIG_BLK_DEV_IDEDMA_PCI $CONFIG_X86
- dep_bool ' SLC90E66 chipset support' CONFIG_BLK_DEV_SLC90E66 $CONFIG_BLK_DEV_IDEDMA_PCI $CONFIG_X86
dep_bool ' Tekram TRM290 chipset support (EXPERIMENTAL)' CONFIG_BLK_DEV_TRM290 $CONFIG_BLK_DEV_IDEDMA_PCI
dep_bool ' VIA82CXXX chipset support' CONFIG_BLK_DEV_VIA82CXXX $CONFIG_BLK_DEV_IDEDMA_PCI
fi
diff -urN linux-2.5.6-timing/drivers/ide/Makefile linux-2.5.6-piix/drivers/ide/Makefile
--- linux-2.5.6-timing/drivers/ide/Makefile Tue Mar 12 16:26:03 2002
+++ linux-2.5.6-piix/drivers/ide/Makefile Wed Mar 13 23:27:16 2002
@@ -61,7 +61,6 @@
ide-obj-$(CONFIG_BLK_DEV_IDE_RAPIDE) += rapide.o
ide-obj-$(CONFIG_BLK_DEV_RZ1000) += rz1000.o
ide-obj-$(CONFIG_BLK_DEV_SIS5513) += sis5513.o
-ide-obj-$(CONFIG_BLK_DEV_SLC90E66) += slc90e66.o
ide-obj-$(CONFIG_BLK_DEV_SL82C105) += sl82c105.o
ide-obj-$(CONFIG_BLK_DEV_TRM290) += trm290.o
ide-obj-$(CONFIG_BLK_DEV_UMC8672) += umc8672.o
diff -urN linux-2.5.6-timing/drivers/ide/ide-pci.c linux-2.5.6-piix/drivers/ide/ide-pci.c
--- linux-2.5.6-timing/drivers/ide/ide-pci.c Tue Mar 12 16:05:37 2002
+++ linux-2.5.6-piix/drivers/ide/ide-pci.c Wed Mar 13 23:57:14 2002
@@ -119,6 +119,7 @@
extern unsigned int pci_init_piix(struct pci_dev *);
extern unsigned int ata66_piix(ide_hwif_t *);
extern void ide_init_piix(ide_hwif_t *);
+extern void ide_dmacapable_piix(ide_hwif_t *, unsigned long);
#endif

#ifdef CONFIG_BLK_DEV_IT8172
@@ -142,12 +143,6 @@
extern void ide_init_sis5513(ide_hwif_t *);
#endif

-#ifdef CONFIG_BLK_DEV_SLC90E66
-extern unsigned int pci_init_slc90e66(struct pci_dev *);
-extern unsigned int ata66_slc90e66(ide_hwif_t *);
-extern void ide_init_slc90e66(ide_hwif_t *);
-#endif
-
#ifdef CONFIG_BLK_DEV_SL82C105
extern unsigned int pci_init_sl82c105(struct pci_dev *);
extern void dma_init_sl82c105(ide_hwif_t *, unsigned long);
@@ -197,19 +192,18 @@

static ide_pci_device_t pci_chipsets[] __initdata = {
#ifdef CONFIG_BLK_DEV_PIIX
- {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371FB_0, NULL, NULL, ide_init_piix, NULL, {{0x41,0x80,0x80}, {0x43,0x80,0x80}}, ON_BOARD, 0, 0 },
- {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371FB_1, NULL, NULL, ide_init_piix, NULL, {{0x41,0x80,0x80}, {0x43,0x80,0x80}}, ON_BOARD, 0, 0 },
- {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371MX, NULL, NULL, ide_init_piix, NULL, {{0x6D,0x80,0x80}, {0x6F,0x80,0x80}}, ON_BOARD, 0, ATA_F_NODMA },
- {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371SB_1, pci_init_piix, NULL, ide_init_piix, NULL, {{0x41,0x80,0x80}, {0x43,0x80,0x80}}, ON_BOARD, 0, 0 },
- {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371AB, pci_init_piix, NULL, ide_init_piix, NULL, {{0x41,0x80,0x80}, {0x43,0x80,0x80}}, ON_BOARD, 0, 0 },
- {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801AB_1, pci_init_piix, NULL, ide_init_piix, NULL, {{0x41,0x80,0x80}, {0x43,0x80,0x80}}, ON_BOARD, 0, 0 },
- {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82443MX_1, pci_init_piix, NULL, ide_init_piix, NULL, {{0x41,0x80,0x80}, {0x43,0x80,0x80}}, ON_BOARD, 0, 0 },
- {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801AA_1, pci_init_piix, ata66_piix, ide_init_piix, NULL, {{0x41,0x80,0x80}, {0x43,0x80,0x80}}, ON_BOARD, 0, 0 },
- {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82372FB_1, pci_init_piix, ata66_piix, ide_init_piix, NULL, {{0x41,0x80,0x80}, {0x43,0x80,0x80}}, ON_BOARD, 0, 0 },
- {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82451NX, pci_init_piix, NULL, ide_init_piix, NULL, {{0x41,0x80,0x80}, {0x43,0x80,0x80}}, ON_BOARD, 0, ATA_F_NOADMA },
- {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801BA_9, pci_init_piix, ata66_piix, ide_init_piix, NULL, {{0x41,0x80,0x80}, {0x43,0x80,0x80}}, ON_BOARD, 0, 0 },
- {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801BA_8, pci_init_piix, ata66_piix, ide_init_piix, NULL, {{0x41,0x80,0x80}, {0x43,0x80,0x80}}, ON_BOARD, 0, 0 },
- {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_10, pci_init_piix, ata66_piix, ide_init_piix, NULL, {{0x41,0x80,0x80}, {0x43,0x80,0x80}}, ON_BOARD, 0, 0 },
+ {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371FB_1, pci_init_piix, ata66_piix, ide_init_piix, ide_dmacapable_piix, {{0x41,0x80,0x80}, {0x43,0x80,0x80}}, ON_BOARD, 0, 0 },
+ {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371SB_1, pci_init_piix, ata66_piix, ide_init_piix, ide_dmacapable_piix, {{0x41,0x80,0x80}, {0x43,0x80,0x80}}, ON_BOARD, 0, 0 },
+ {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371AB, pci_init_piix, ata66_piix, ide_init_piix, ide_dmacapable_piix, {{0x41,0x80,0x80}, {0x43,0x80,0x80}}, ON_BOARD, 0, 0 },
+ {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82443MX_1, pci_init_piix, ata66_piix, ide_init_piix, ide_dmacapable_piix, {{0x41,0x80,0x80}, {0x43,0x80,0x80}}, ON_BOARD, 0, 0 },
+ {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82372FB_1, pci_init_piix, ata66_piix, ide_init_piix, ide_dmacapable_piix, {{0x41,0x80,0x80}, {0x43,0x80,0x80}}, ON_BOARD, 0, 0 },
+ {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801AA_1, pci_init_piix, ata66_piix, ide_init_piix, ide_dmacapable_piix, {{0x41,0x80,0x80}, {0x43,0x80,0x80}}, ON_BOARD, 0, 0 },
+ {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801AB_1, pci_init_piix, ata66_piix, ide_init_piix, ide_dmacapable_piix, {{0x41,0x80,0x80}, {0x43,0x80,0x80}}, ON_BOARD, 0, 0 },
+ {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801BA_9, pci_init_piix, ata66_piix, ide_init_piix, ide_dmacapable_piix, {{0x41,0x80,0x80}, {0x43,0x80,0x80}}, ON_BOARD, 0, 0 },
+ {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801BA_8, pci_init_piix, ata66_piix, ide_init_piix, ide_dmacapable_piix, {{0x41,0x80,0x80}, {0x43,0x80,0x80}}, ON_BOARD, 0, 0 },
+ {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_10, pci_init_piix, ata66_piix, ide_init_piix, ide_dmacapable_piix, {{0x41,0x80,0x80}, {0x43,0x80,0x80}}, ON_BOARD, 0, 0 },
+ {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82801CA_11, pci_init_piix, ata66_piix, ide_init_piix, ide_dmacapable_piix, {{0x41,0x80,0x80}, {0x43,0x80,0x80}}, ON_BOARD, 0, 0 },
+ {PCI_VENDOR_ID_EFAR, PCI_DEVICE_ID_EFAR_SLC90E66_1, pci_init_piix, ata66_piix, ide_init_piix, ide_dmacapable_piix, {{0x41,0x80,0x80}, {0x43,0x80,0x80}}, ON_BOARD, 0, 0 },
#endif
#ifdef CONFIG_BLK_DEV_VIA82CXXX
{PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C576_1, pci_init_via82cxxx, ata66_via82cxxx, ide_init_via82cxxx, ide_dmacapable_via82cxxx, {{0x40,0x02,0x02}, {0x40,0x01,0x01}}, ON_BOARD, 0, ATA_F_NOADMA },
@@ -293,9 +287,6 @@
#ifdef CONFIG_BLK_DEV_PDC_ADMA
{PCI_VENDOR_ID_PDC, PCI_DEVICE_ID_PDC_1841, pci_init_pdcadma, ata66_pdcadma, ide_init_pdcadma, ide_dmacapable_pdcadma, {{0x00,0x00,0x00}, {0x00,0x00,0x00}}, OFF_BOARD, 0, ATA_F_NODMA },
#endif
-#ifdef CONFIG_BLK_DEV_SLC90E66
- {PCI_VENDOR_ID_EFAR, PCI_DEVICE_ID_EFAR_SLC90E66_1, pci_init_slc90e66, ata66_slc90e66, ide_init_slc90e66, NULL, {{0x41,0x80,0x80}, {0x43,0x80,0x80}}, ON_BOARD, 0, 0 },
-#endif
#ifdef CONFIG_BLK_DEV_SVWKS
{PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_OSB4IDE, pci_init_svwks, ata66_svwks, ide_init_svwks, NULL, {{0x00,0x00,0x00}, {0x00,0x00,0x00}}, ON_BOARD, 0, ATA_F_DMA },
{PCI_VENDOR_ID_SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB5IDE, pci_init_svwks, ata66_svwks, ide_init_svwks, NULL, {{0x00,0x00,0x00}, {0x00,0x00,0x00}}, ON_BOARD, 0, 0 },
@@ -311,6 +302,7 @@
{PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_87410, NULL, NULL, NULL, NULL, {{0x43,0x08,0x08}, {0x47,0x08,0x08}}, ON_BOARD, 0, 0 },
{PCI_VENDOR_ID_HINT, PCI_DEVICE_ID_HINT, NULL, NULL, NULL, NULL, {{0x00,0x00,0x00}, {0x00,0x00,0x00}}, ON_BOARD, 0, 0 },
{PCI_VENDOR_ID_HOLTEK, PCI_DEVICE_ID_HOLTEK_6565, NULL, NULL, NULL, NULL, {{0x00,0x00,0x00}, {0x00,0x00,0x00}}, ON_BOARD, 0, 0 },
+ {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371MX, NULL, NULL, NULL, NULL, {{0x6D,0x80,0x80}, {0x00,0x00,0x00}}, ON_BOARD, 0, ATA_F_NODMA },
{PCI_VENDOR_ID_UMC, PCI_DEVICE_ID_UMC_UM8673F, NULL, NULL, NULL, NULL, {{0x00,0x00,0x00}, {0x00,0x00,0x00}}, ON_BOARD, 0, ATA_F_FIXIRQ },
{PCI_VENDOR_ID_UMC, PCI_DEVICE_ID_UMC_UM8886A, NULL, NULL, NULL, NULL, {{0x00,0x00,0x00}, {0x00,0x00,0x00}}, ON_BOARD, 0, ATA_F_FIXIRQ },
{PCI_VENDOR_ID_UMC, PCI_DEVICE_ID_UMC_UM8886BF, NULL, NULL, NULL, NULL, {{0x00,0x00,0x00}, {0x00,0x00,0x00}}, ON_BOARD, 0, ATA_F_FIXIRQ },
diff -urN linux-2.5.6-timing/drivers/ide/piix.c linux-2.5.6-piix/drivers/ide/piix.c
--- linux-2.5.6-timing/drivers/ide/piix.c Tue Mar 12 16:26:03 2002
+++ linux-2.5.6-piix/drivers/ide/piix.c Wed Mar 13 23:58:16 2002
@@ -1,499 +1,547 @@
/*
- * linux/drivers/ide/piix.c Version 0.32 June 9, 2000
+ * $Id: piix.c,v 1.2 2002/03/13 22:50:43 vojtech Exp $
*
- * Copyright (C) 1998-1999 Andrzej Krzysztofowicz, Author and Maintainer
- * Copyright (C) 1998-2000 Andre Hedrick <andre@linux-ide.org>
- * May be copied or modified under the terms of the GNU General Public License
+ * Copyright (c) 2000-2002 Vojtech Pavlik
*
- * PIO mode setting function for Intel chipsets.
- * For use instead of BIOS settings.
- *
- * 40-41
- * 42-43
- *
- * 41
- * 43
- *
- * | PIO 0 | c0 | 80 | 0 | piix_tune_drive(drive, 0);
- * | PIO 2 | SW2 | d0 | 90 | 4 | piix_tune_drive(drive, 2);
- * | PIO 3 | MW1 | e1 | a1 | 9 | piix_tune_drive(drive, 3);
- * | PIO 4 | MW2 | e3 | a3 | b | piix_tune_drive(drive, 4);
- *
- * sitre = word40 & 0x4000; primary
- * sitre = word42 & 0x4000; secondary
- *
- * 44 8421|8421 hdd|hdb
- *
- * 48 8421 hdd|hdc|hdb|hda udma enabled
- *
- * 0001 hda
- * 0010 hdb
- * 0100 hdc
- * 1000 hdd
- *
- * 4a 84|21 hdb|hda
- * 4b 84|21 hdd|hdc
- *
- * ata-33/82371AB
- * ata-33/82371EB
- * ata-33/82801AB ata-66/82801AA
- * 00|00 udma 0 00|00 reserved
- * 01|01 udma 1 01|01 udma 3
- * 10|10 udma 2 10|10 udma 4
- * 11|11 reserved 11|11 reserved
- *
- * 54 8421|8421 ata66 drive|ata66 enable
- *
- * pci_read_config_word(HWIF(drive)->pci_dev, 0x40, &reg40);
- * pci_read_config_word(HWIF(drive)->pci_dev, 0x42, &reg42);
- * pci_read_config_word(HWIF(drive)->pci_dev, 0x44, &reg44);
- * pci_read_config_word(HWIF(drive)->pci_dev, 0x48, &reg48);
- * pci_read_config_word(HWIF(drive)->pci_dev, 0x4a, &reg4a);
- * pci_read_config_word(HWIF(drive)->pci_dev, 0x54, &reg54);
+ * Based on the work of:
+ * Andrzej Krzysztofowicz
+ * Andre Hedrick
+ */
+
+/*
+ * Intel PIIX/ICH and Efar Victory66 IDE driver for Linux.
*
+ * UDMA66 and higher modes are autoenabled only in case the BIOS has detected a
+ * 80 wire cable. To ignore the BIOS data and assume the cable is present, use
+ * 'ide0=ata66' or 'ide1=ata66' on the kernel command line.
+ */
+
+/*
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ *
+ * Should you need to contact me, the author, you can do so either by
+ * e-mail - mail your message to <vojtech@ucw.cz>, or by paper mail:
+ * Vojtech Pavlik, Simunkova 1594, Prague 8, 182 00 Czech Republic
*/

#include <linux/config.h>
-#include <linux/types.h>
#include <linux/kernel.h>
#include <linux/ioport.h>
+#include <linux/blkdev.h>
#include <linux/pci.h>
-#include <linux/hdreg.h>
-#include <linux/ide.h>
-#include <linux/delay.h>
#include <linux/init.h>
-
+#include <linux/ide.h>
#include <asm/io.h>

#include "ide-timing.h"

-#define PIIX_DEBUG_DRIVE_INFO 0
+#define PIIX_IDETIM0 0x40
+#define PIIX_IDETIM1 0x42
+#define PIIX_SIDETIM 0x44
+#define PIIX_IDESTAT 0x47
+#define PIIX_UDMACTL 0x48
+#define PIIX_UDMATIM 0x4a
+#define PIIX_IDECFG 0x54
+
+#define PIIX_UDMA 0x07
+#define PIIX_UDMA_NONE 0x00
+#define PIIX_UDMA_33 0x01
+#define PIIX_UDMA_66 0x02
+#define PIIX_UDMA_V66 0x03
+#define PIIX_UDMA_100 0x04
+#define PIIX_NO_SITRE 0x08
+#define PIIX_PINGPONG 0x10
+#define PIIX_VICTORY 0x20
+
+/*
+ * Intel IDE chips
+ */
+
+static struct piix_ide_chip {
+ char *name;
+ unsigned short id;
+ unsigned char flags;
+} piix_ide_chips[] = {
+ { "Intel 82801CA ICH3", PCI_DEVICE_ID_INTEL_82801CA_11, PIIX_UDMA_100 | PIIX_PINGPONG },
+ { "Intel 82801CAM ICH3-M", PCI_DEVICE_ID_INTEL_82801CA_10, PIIX_UDMA_100 | PIIX_PINGPONG },
+ { "Intel 82801BA ICH2", PCI_DEVICE_ID_INTEL_82801BA_9, PIIX_UDMA_100 | PIIX_PINGPONG },
+ { "Intel 82801BAM ICH2-M", PCI_DEVICE_ID_INTEL_82801BA_8, PIIX_UDMA_100 | PIIX_PINGPONG },
+ { "Intel 82801AB ICH0", PCI_DEVICE_ID_INTEL_82801AB_1, PIIX_UDMA_33 | PIIX_PINGPONG },
+ { "Intel 82801AA ICH", PCI_DEVICE_ID_INTEL_82801AA_1, PIIX_UDMA_66 | PIIX_PINGPONG },
+ { "Intel 82372FB PIIX5", PCI_DEVICE_ID_INTEL_82372FB_1, PIIX_UDMA_66 },
+ { "Intel 82443MX MPIIX4", PCI_DEVICE_ID_INTEL_82443MX_1, PIIX_UDMA_33 },
+ { "Intel 82371AB/EB PIIX4/4E", PCI_DEVICE_ID_INTEL_82371AB, PIIX_UDMA_33 },
+ { "Intel 82371SB PIIX3", PCI_DEVICE_ID_INTEL_82371SB_1, PIIX_UDMA_NONE },
+ { "Intel 82371FB PIIX", PCI_DEVICE_ID_INTEL_82371FB_1, PIIX_UDMA_NONE | PIIX_NO_SITRE },
+ { "Efar Victory66", PCI_DEVICE_ID_EFAR_SLC90E66_1, PIIX_UDMA_V66 | PIIX_VICTORY },
+ { NULL }
+};
+
+static struct piix_ide_chip *piix_config;
+static unsigned char piix_enabled;
+static unsigned int piix_80w;
+static unsigned int piix_clock;
+
+static char *piix_dma[] = { "MWDMA16", "UDMA33", "UDMA66", "UDMA66", "UDMA100" };
+
+/*
+ * PIIX/ICH /proc entry.
+ */

-#define DISPLAY_PIIX_TIMINGS
+#ifdef CONFIG_PROC_FS

-#if defined(DISPLAY_PIIX_TIMINGS) && defined(CONFIG_PROC_FS)
#include <linux/stat.h>
#include <linux/proc_fs.h>

-static int piix_get_info(char *, char **, off_t, int);
-extern int (*piix_display_info)(char *, char **, off_t, int); /* ide-proc.c */
+byte piix_proc;
+int piix_base;
static struct pci_dev *bmide_dev;
+extern int (*piix_display_info)(char *, char **, off_t, int); /* ide-proc.c */
+
+#define piix_print(format, arg...) p += sprintf(p, format "\n" , ## arg)
+#define piix_print_drive(name, format, arg...)\
+ p += sprintf(p, name); for (i = 0; i < 4; i++) p += sprintf(p, format, ## arg); p += sprintf(p, "\n");

-static int piix_get_info (char *buffer, char **addr, off_t offset, int count)
+static int piix_get_info(char *buffer, char **addr, off_t offset, int count)
{
+ int speed[4], cycle[4], active[4], recover[4], dmaen[4], uen[4], udma[4], umul;
+ struct pci_dev *dev = bmide_dev;
+ unsigned int i, u;
+ unsigned short c, d, e;
+ unsigned char t;
char *p = buffer;
- u32 bibma = pci_resource_start(bmide_dev, 4);
- u16 reg40 = 0, psitre = 0, reg42 = 0, ssitre = 0;
- u8 c0 = 0, c1 = 0;
- u8 reg44 = 0, reg48 = 0, reg4a = 0, reg4b = 0, reg54 = 0, reg55 = 0;
-
- if (bmide_dev->device == PCI_DEVICE_ID_INTEL_82371MX) {
- p += sprintf(p, "\n Intel MPIIX Chipset.\n");
- return p-buffer; /* => must be less than 4k! */
- }
-
- pci_read_config_word(bmide_dev, 0x40, &reg40);
- pci_read_config_word(bmide_dev, 0x42, &reg42);
- pci_read_config_byte(bmide_dev, 0x44, &reg44);
- pci_read_config_byte(bmide_dev, 0x48, &reg48);
- pci_read_config_byte(bmide_dev, 0x4a, &reg4a);
- pci_read_config_byte(bmide_dev, 0x4b, &reg4b);
- pci_read_config_byte(bmide_dev, 0x54, &reg54);
- pci_read_config_byte(bmide_dev, 0x55, &reg55);
-
- psitre = (reg40 & 0x4000) ? 1 : 0;
- ssitre = (reg42 & 0x4000) ? 1 : 0;
-
- /*
- * at that point bibma+0x2 et bibma+0xa are byte registers
- * to investigate:
- */
- c0 = inb_p((unsigned short)bibma + 0x02);
- c1 = inb_p((unsigned short)bibma + 0x0a);
-
- p += sprintf(p, "\n %s Chipset.\n", bmide_dev->name);
- p += sprintf(p, "--------------- Primary Channel ---------------- Secondary Channel -------------\n");
- p += sprintf(p, " %sabled %sabled\n",
- (c0&0x80) ? "dis" : " en",
- (c1&0x80) ? "dis" : " en");
- p += sprintf(p, "--------------- drive0 --------- drive1 -------- drive0 ---------- drive1 ------\n");
- p += sprintf(p, "DMA enabled: %s %s %s %s\n",
- (c0&0x20) ? "yes" : "no ",
- (c0&0x40) ? "yes" : "no ",
- (c1&0x20) ? "yes" : "no ",
- (c1&0x40) ? "yes" : "no " );
- p += sprintf(p, "UDMA enabled: %s %s %s %s\n",
- (reg48&0x01) ? "yes" : "no ",
- (reg48&0x02) ? "yes" : "no ",
- (reg48&0x04) ? "yes" : "no ",
- (reg48&0x08) ? "yes" : "no " );
- p += sprintf(p, "UDMA enabled: %s %s %s %s\n",
- ((reg54&0x11) && (reg55&0x10) && (reg4a&0x01)) ? "5" :
- ((reg54&0x11) && (reg4a&0x02)) ? "4" :
- ((reg54&0x11) && (reg4a&0x01)) ? "3" :
- (reg4a&0x02) ? "2" :
- (reg4a&0x01) ? "1" :
- (reg4a&0x00) ? "0" : "X",
- ((reg54&0x22) && (reg55&0x20) && (reg4a&0x10)) ? "5" :
- ((reg54&0x22) && (reg4a&0x20)) ? "4" :
- ((reg54&0x22) && (reg4a&0x10)) ? "3" :
- (reg4a&0x20) ? "2" :
- (reg4a&0x10) ? "1" :
- (reg4a&0x00) ? "0" : "X",
- ((reg54&0x44) && (reg55&0x40) && (reg4b&0x03)) ? "5" :
- ((reg54&0x44) && (reg4b&0x02)) ? "4" :
- ((reg54&0x44) && (reg4b&0x01)) ? "3" :
- (reg4b&0x02) ? "2" :
- (reg4b&0x01) ? "1" :
- (reg4b&0x00) ? "0" : "X",
- ((reg54&0x88) && (reg55&0x80) && (reg4b&0x30)) ? "5" :
- ((reg54&0x88) && (reg4b&0x20)) ? "4" :
- ((reg54&0x88) && (reg4b&0x10)) ? "3" :
- (reg4b&0x20) ? "2" :
- (reg4b&0x10) ? "1" :
- (reg4b&0x00) ? "0" : "X");
-
- p += sprintf(p, "UDMA\n");
- p += sprintf(p, "DMA\n");
- p += sprintf(p, "PIO\n");

-/*
- * FIXME.... Add configuration junk data....blah blah......
- */
+ piix_print("----------PIIX BusMastering IDE Configuration---------------");

- return p-buffer; /* => must be less than 4k! */
-}
-#endif /* defined(DISPLAY_PIIX_TIMINGS) && defined(CONFIG_PROC_FS) */
+ piix_print("Driver Version: 1.2");
+ piix_print("South Bridge: %s", piix_config->name);

-/*
- * Used to set Fifo configuration via kernel command line:
- */
+ pci_read_config_byte(dev, PCI_REVISION_ID, &t);
+ piix_print("Revision: IDE %#x", t);
+ piix_print("Highest DMA rate: %s", piix_dma[piix_config->flags & PIIX_UDMA]);

-byte piix_proc = 0;
+ piix_print("BM-DMA base: %#x", piix_base);
+ piix_print("PCI clock: %d.%dMHz", piix_clock / 1000, piix_clock / 100 % 10);

-extern char *ide_xfer_verbose (byte xfer_rate);
+ piix_print("-----------------------Primary IDE-------Secondary IDE------");

-#if defined(CONFIG_BLK_DEV_IDEDMA) && defined(CONFIG_PIIX_TUNING)
-/*
- *
- */
-static byte piix_dma_2_pio (byte xfer_rate) {
- switch(xfer_rate) {
- case XFER_UDMA_5:
- case XFER_UDMA_4:
- case XFER_UDMA_3:
- case XFER_UDMA_2:
- case XFER_UDMA_1:
- case XFER_UDMA_0:
- case XFER_MW_DMA_2:
- case XFER_PIO_4:
- return 4;
- case XFER_MW_DMA_1:
- case XFER_PIO_3:
- return 3;
- case XFER_SW_DMA_2:
- case XFER_PIO_2:
- return 2;
- case XFER_MW_DMA_0:
- case XFER_SW_DMA_1:
- case XFER_SW_DMA_0:
- case XFER_PIO_1:
- case XFER_PIO_0:
- case XFER_PIO_SLOW:
- default:
- return 0;
+ pci_read_config_word(dev, PIIX_IDETIM0, &d);
+ pci_read_config_word(dev, PIIX_IDETIM1, &e);
+ piix_print("Enabled: %10s%20s", (d & 0x8000) ? "yes" : "no", (e & 0x8000) ? "yes" : "no");
+
+ c = inb(piix_base + 0x02) | (inb(piix_base + 0x0a) << 8);
+ piix_print("Simplex only: %10s%20s", (c & 0x80) ? "yes" : "no", (c & 0x8000) ? "yes" : "no");
+
+ piix_print("Cable Type: %10s%20s", (piix_80w & 1) ? "80w" : "40w", (piix_80w & 2) ? "80w" : "40w");
+
+ if (!piix_clock)
+ return p - buffer;
+
+ piix_print("-------------------drive0----drive1----drive2----drive3-----");
+
+ piix_print_drive("Prefetch+Post: ", "%10s", (((i & 2) ? d : e) & (1 << (2 + ((i & 1) << 2)))) ? "yes" : "no");
+
+ for (i = 0; i < 4; i++) {
+
+ pci_read_config_word(dev, PIIX_IDETIM0 + (i & 2), &d);
+ if (~piix_config->flags & PIIX_NO_SITRE)
+ pci_read_config_byte(dev, PIIX_SIDETIM, &t);
+
+ umul = 4;
+ udma[i] = uen[i] = 0;
+ active[i] = 12;
+ recover[i] = 18;
+
+ switch (i & 1) {
+ case 1: if (~d & 0x10) break;
+ if ((~piix_config->flags & PIIX_NO_SITRE) && (d & 0x4000)) {
+ active[i] = 5 - ((t >> (((i & 2) << 1) + 2)) & 3);
+ recover[i] = 4 - ((t >> (((i & 2) << 1) + 0)) & 3);
+ break;
+ }
+
+ case 0: if (~d & 0x01) break;
+ active[i] = 5 - ((d >> 12) & 3);
+ recover[i] = 4 - ((d >> 8) & 3);
+ }
+
+ dmaen[i] = (c & ((i & 1) ? 0x40 : 0x20) << ((i & 2) << 2));
+ cycle[i] = 1000000 / piix_clock * (active[i] + recover[i]);
+ speed[i] = 2 * piix_clock / (active[i] + recover[i]);
+
+ if (!(piix_config->flags & PIIX_UDMA))
+ continue;
+
+ pci_read_config_byte(dev, PIIX_UDMACTL, &t);
+ uen[i] = (t & (1 << i)) ? dmaen[i] : 0;
+
+ if (!uen[i])
+ continue;
+
+ pci_read_config_word(dev, PIIX_UDMATIM, &e);
+ pci_read_config_dword(dev, PIIX_IDECFG, &u);
+
+ if (~piix_config->flags & PIIX_VICTORY) {
+ if ((piix_config->flags & PIIX_UDMA) >= PIIX_UDMA_66 && (u & (1 << i))) umul = 2;
+ if ((piix_config->flags & PIIX_UDMA) >= PIIX_UDMA_100 && (u & ((1 << i) + 12))) umul = 1;
+ udma[i] = (4 - ((e >> (i << 2)) & 3)) * umul;
+ } else udma[i] = (8 - ((e >> (i << 2)) & 7)) * 2;
+
+ speed[i] = 8 * piix_clock / udma[i];
+ cycle[i] = 250000 * udma[i] / piix_clock;
}
+
+ piix_print_drive("Transfer Mode: ", "%10s", dmaen[i] ? (uen[i] ? "UDMA" : "DMA") : "PIO");
+
+ piix_print_drive("Address Setup: ", "%8dns", (1000000 / piix_clock) * 3);
+ piix_print_drive("Cmd Active: ", "%8dns", (1000000 / piix_clock) * 12);
+ piix_print_drive("Cmd Recovery: ", "%8dns", (1000000 / piix_clock) * 18);
+ piix_print_drive("Data Active: ", "%8dns", (1000000 / piix_clock) * active[i]);
+ piix_print_drive("Data Recovery: ", "%8dns", (1000000 / piix_clock) * recover[i]);
+ piix_print_drive("Cycle Time: ", "%8dns", cycle[i]);
+ piix_print_drive("Transfer Rate: ", "%4d.%dMB/s", speed[i] / 1000, speed[i] / 100 % 10);
+
+ return p - buffer; /* hoping it is less than 4K... */
}
-#endif /* defined(CONFIG_BLK_DEV_IDEDMA) && (CONFIG_PIIX_TUNING) */
+
+#endif

/*
- * Based on settings done by AMI BIOS
- * (might be useful if drive is not registered in CMOS for any reason).
+ * piix_set_speed() writes timing values to the chipset registers
*/
-static void piix_tune_drive (ide_drive_t *drive, byte pio)
-{
- unsigned long flags;
- u16 master_data;
- u8 slave_data;
- int is_slave = (&HWIF(drive)->drives[1] == drive);
- int master_port = HWIF(drive)->index ? 0x42 : 0x40;
- int slave_port = 0x44;
- /* ISP RTC */
- byte timings[][2] = { { 0, 0 },
- { 0, 0 },
- { 1, 0 },
- { 2, 1 },
- { 2, 3 }, };
-
- if (pio == 255)
- pio = ide_find_best_mode(drive, XFER_PIO | XFER_EPIO) - XFER_PIO_0;
- else
- pio = min_t(byte, pio, 4);
-
- pci_read_config_word(HWIF(drive)->pci_dev, master_port, &master_data);
- if (is_slave) {
- master_data = master_data | 0x4000;
- if (pio > 1)
- /* enable PPE, IE and TIME */
- master_data = master_data | 0x0070;
- pci_read_config_byte(HWIF(drive)->pci_dev, slave_port, &slave_data);
- slave_data = slave_data & (HWIF(drive)->index ? 0x0f : 0xf0);
- slave_data = slave_data | (((timings[pio][0] << 2) | timings[pio][1])
- << (HWIF(drive)->index ? 4 : 0));
- } else {
- master_data = master_data & 0xccf8;
- if (pio > 1)
- /* enable PPE, IE and TIME */
- master_data = master_data | 0x0007;
- master_data = master_data | (timings[pio][0] << 12) |
- (timings[pio][1] << 8);
- }
- save_flags(flags);
- cli();
- pci_write_config_word(HWIF(drive)->pci_dev, master_port, master_data);
- if (is_slave)
- pci_write_config_byte(HWIF(drive)->pci_dev, slave_port, slave_data);
- restore_flags(flags);
-}

-#if defined(CONFIG_BLK_DEV_IDEDMA) && defined(CONFIG_PIIX_TUNING)
-static int piix_tune_chipset (ide_drive_t *drive, byte speed)
+static void piix_set_speed(struct pci_dev *dev, unsigned char dn, struct ide_timing *timing, int umul)
{
- ide_hwif_t *hwif = HWIF(drive);
- struct pci_dev *dev = hwif->pci_dev;
- byte maslave = hwif->channel ? 0x42 : 0x40;
- int a_speed = 3 << (drive->dn * 4);
- int u_flag = 1 << drive->dn;
- int v_flag = 0x01 << drive->dn;
- int w_flag = 0x10 << drive->dn;
- int u_speed = 0;
- int err = 0;
- int sitre;
- short reg4042, reg44, reg48, reg4a, reg54;
- byte reg55;
-
- pci_read_config_word(dev, maslave, &reg4042);
- sitre = (reg4042 & 0x4000) ? 1 : 0;
- pci_read_config_word(dev, 0x44, &reg44);
- pci_read_config_word(dev, 0x48, &reg48);
- pci_read_config_word(dev, 0x4a, &reg4a);
- pci_read_config_word(dev, 0x54, &reg54);
- pci_read_config_byte(dev, 0x55, &reg55);
-
- switch(speed) {
- case XFER_UDMA_4:
- case XFER_UDMA_2: u_speed = 2 << (drive->dn * 4); break;
- case XFER_UDMA_5:
- case XFER_UDMA_3:
- case XFER_UDMA_1: u_speed = 1 << (drive->dn * 4); break;
- case XFER_UDMA_0: u_speed = 0 << (drive->dn * 4); break;
- case XFER_MW_DMA_2:
- case XFER_MW_DMA_1:
- case XFER_SW_DMA_2: break;
- default: return -1;
- }
-
- if (speed >= XFER_UDMA_0) {
- if (!(reg48 & u_flag))
- pci_write_config_word(dev, 0x48, reg48|u_flag);
- if (speed == XFER_UDMA_5) {
- pci_write_config_byte(dev, 0x55, (byte) reg55|w_flag);
+ unsigned short t;
+ unsigned char u;
+ unsigned int c;
+
+ pci_read_config_word(dev, PIIX_IDETIM0 + (dn & 2), &t);
+
+ switch (dn & 1) {
+
+ case 1:
+ if (timing->cycle > 9) {
+ t &= ~0x30;
+ break;
+ }
+
+ if (~piix_config->flags & PIIX_NO_SITRE) {
+ pci_read_config_byte(dev, PIIX_SIDETIM, &u);
+ u &= ~(0xf << ((dn & 2) << 1));
+ t |= 0x30;
+ u |= (4 - FIT(timing->recover, 1, 4)) << ((dn & 2) << 1);
+ u |= (5 - FIT(timing->active, 2, 5)) << (((dn & 2) << 1) + 2);
+ pci_write_config_byte(dev, PIIX_SIDETIM, u);
+ break;
+ }
+
+ case 0:
+ if ((~dn & 1) && timing->cycle > 9) {
+ t &= ~0x03;
+ break;
+ }
+
+ t &= 0xccff;
+ t |= 0x03 << ((dn & 1) << 2);
+ t |= (4 - FIT(timing->recover, 1, 4)) << 8;
+ t |= (5 - FIT(timing->active, 2, 5)) << 12;
+ }
+
+ pci_write_config_word(dev, PIIX_IDETIM0 + (dn & 2), t);
+
+ if (!(piix_config->flags & PIIX_UDMA)) return;
+
+ pci_read_config_byte(dev, PIIX_UDMACTL, &u);
+ u &= ~(1 << dn);
+
+ if (timing->udma) {
+
+ u |= 1 << dn;
+
+ pci_read_config_word(dev, PIIX_UDMATIM, &t);
+
+ if (piix_config->flags & PIIX_VICTORY) {
+ t &= ~(0x07 << (dn << 2));
+ t |= (8 - FIT(timing->udma, 2, 8)) << (dn << 2);
} else {
- pci_write_config_byte(dev, 0x55, (byte) reg55 & ~w_flag);
+ t &= ~(0x03 << (dn << 2));
+ t |= (4 - FIT(timing->udma, 2, 4)) << (dn << 2);
}
- if (!(reg4a & u_speed)) {
- pci_write_config_word(dev, 0x4a, reg4a & ~a_speed);
- pci_write_config_word(dev, 0x4a, reg4a|u_speed);
- }
- if (speed > XFER_UDMA_2) {
- if (!(reg54 & v_flag)) {
- pci_write_config_word(dev, 0x54, reg54|v_flag);
+
+ pci_write_config_word(dev, PIIX_UDMATIM, t);
+
+ if ((piix_config->flags & PIIX_UDMA) > PIIX_UDMA_33
+ && ~piix_config->flags & PIIX_VICTORY) {
+
+ pci_read_config_dword(dev, PIIX_IDECFG, &c);
+
+ if ((piix_config->flags & PIIX_UDMA) > PIIX_UDMA_66)
+ c &= ~(1 << (dn + 12));
+ c &= ~(1 << dn);
+
+ switch (umul) {
+ case 2: c |= 1 << dn; break;
+ case 4: c |= 1 << (dn + 12); break;
}
- } else {
- pci_write_config_word(dev, 0x54, reg54 & ~v_flag);
+
+ pci_write_config_dword(dev, PIIX_IDECFG, c);
}
}
- if (speed < XFER_UDMA_0) {
- if (reg48 & u_flag)
- pci_write_config_word(dev, 0x48, reg48 & ~u_flag);
- if (reg4a & a_speed)
- pci_write_config_word(dev, 0x4a, reg4a & ~a_speed);
- if (reg54 & v_flag)
- pci_write_config_word(dev, 0x54, reg54 & ~v_flag);
- if (reg55 & w_flag)
- pci_write_config_byte(dev, 0x55, (byte) reg55 & ~w_flag);
- }
-
- piix_tune_drive(drive, piix_dma_2_pio(speed));
-
-#if PIIX_DEBUG_DRIVE_INFO
- printk("%s: %s drive%d\n", drive->name, ide_xfer_verbose(speed), drive->dn);
-#endif /* PIIX_DEBUG_DRIVE_INFO */
- if (!drive->init_speed)
- drive->init_speed = speed;
- err = ide_config_drive_speed(drive, speed);
- drive->current_speed = speed;
- return err;
-}

-static int piix_config_drive_for_dma (ide_drive_t *drive)
-{
- struct hd_driveid *id = drive->id;
- ide_hwif_t *hwif = HWIF(drive);
- struct pci_dev *dev = hwif->pci_dev;
- byte speed;
-
- byte udma_66 = eighty_ninty_three(drive);
- int ultra100 = ((dev->device == PCI_DEVICE_ID_INTEL_82801BA_8) ||
- (dev->device == PCI_DEVICE_ID_INTEL_82801BA_9) ||
- (dev->device == PCI_DEVICE_ID_INTEL_82801CA_10)) ? 1 : 0;
- int ultra66 = ((ultra100) ||
- (dev->device == PCI_DEVICE_ID_INTEL_82801AA_1) ||
- (dev->device == PCI_DEVICE_ID_INTEL_82372FB_1)) ? 1 : 0;
- int ultra = ((ultra66) ||
- (dev->device == PCI_DEVICE_ID_INTEL_82371AB) ||
- (dev->device == PCI_DEVICE_ID_INTEL_82443MX_1) ||
- (dev->device == PCI_DEVICE_ID_INTEL_82451NX) ||
- (dev->device == PCI_DEVICE_ID_INTEL_82801AB_1)) ? 1 : 0;
-
- speed = ide_find_best_mode(drive, XFER_PIO | XFER_EPIO | XFER_SWDMA | XFER_MWDMA
- | (ultra ? XFER_UDMA : 0) | ((udma_66 & ultra66) ? XFER_UDMA_66 : 0)
- | ((udma_66 & ultra100) ? XFER_UDMA_100 : 0));
-
- (void) piix_tune_chipset(drive, speed);
-
- return ((int) ((id->dma_ultra >> 11) & 7) ? ide_dma_on :
- ((id->dma_ultra >> 8) & 7) ? ide_dma_on :
- ((id->dma_mword >> 8) & 7) ? ide_dma_on :
- ((id->dma_1word >> 8) & 7) ? ide_dma_on :
- ide_dma_off_quietly);
+ pci_write_config_byte(dev, PIIX_UDMACTL, u);
}

-static void config_chipset_for_pio (ide_drive_t *drive)
+/*
+ * piix_set_drive() computes timing values configures the drive and
+ * the chipset to a desired transfer mode. It also can be called
+ * by upper layers.
+ */
+
+static int piix_set_drive(ide_drive_t *drive, unsigned char speed)
{
- piix_tune_drive(drive, ide_find_best_mode(drive, XFER_PIO | XFER_EPIO) - XFER_PIO_0);
+ ide_drive_t *peer = HWIF(drive)->drives + (~drive->dn & 1);
+ struct ide_timing t, p;
+ int err, T, UT, umul;
+
+ if (speed != XFER_PIO_SLOW && speed != drive->current_speed)
+ if ((err = ide_config_drive_speed(drive, speed)))
+ return err;
+
+ umul = min((speed > XFER_UDMA_4) ? 4 : ((speed > XFER_UDMA_2) ? 2 : 1),
+ piix_config->flags & PIIX_UDMA);
+
+ if (piix_config->flags & PIIX_VICTORY)
+ umul = 2;
+
+ T = 1000000000 / piix_clock;
+ UT = T / umul;
+
+ ide_timing_compute(drive, speed, &t, T, UT);
+
+ if ((piix_config->flags & PIIX_NO_SITRE) && peer->present) {
+ ide_timing_compute(peer, peer->current_speed, &p, T, UT);
+ if (t.cycle <= 9 && p.cycle <= 9)
+ ide_timing_merge(&p, &t, &t, IDE_TIMING_ALL);
+ }
+
+ piix_set_speed(HWIF(drive)->pci_dev, drive->dn, &t, umul);
+
+ if (!drive->init_speed)
+ drive->init_speed = speed;
+ drive->current_speed = speed;
+
+ return 0;
}

-static int config_drive_xfer_rate (ide_drive_t *drive)
+/*
+ * piix_tune_drive() is a callback from upper layers for
+ * PIO-only tuning.
+ */
+
+static void piix_tune_drive(ide_drive_t *drive, unsigned char pio)
{
- struct hd_driveid *id = drive->id;
- ide_dma_action_t dma_func = ide_dma_on;
+ if (!((piix_enabled >> HWIF(drive)->channel) & 1))
+ return;

- if (id && (id->capability & 1) && HWIF(drive)->autodma) {
- /* Consult the list of known "bad" drives */
- if (ide_dmaproc(ide_dma_bad_drive, drive)) {
- dma_func = ide_dma_off;
- goto fast_ata_pio;
- }
- dma_func = ide_dma_off_quietly;
- if (id->field_valid & 4) {
- if (id->dma_ultra & 0x003F) {
- /* Force if Capable UltraDMA */
- dma_func = piix_config_drive_for_dma(drive);
- if ((id->field_valid & 2) &&
- (dma_func != ide_dma_on))
- goto try_dma_modes;
- }
- } else if (id->field_valid & 2) {
-try_dma_modes:
- if ((id->dma_mword & 0x0007) ||
- (id->dma_1word & 0x007)) {
- /* Force if Capable regular DMA modes */
- dma_func = piix_config_drive_for_dma(drive);
- if (dma_func != ide_dma_on)
- goto no_dma_set;
- }
- } else if (ide_dmaproc(ide_dma_good_drive, drive)) {
- if (id->eide_dma_time > 150) {
- goto no_dma_set;
- }
- /* Consult the list of known "good" drives */
- dma_func = piix_config_drive_for_dma(drive);
- if (dma_func != ide_dma_on)
- goto no_dma_set;
- } else {
- goto fast_ata_pio;
- }
- } else if ((id->capability & 8) || (id->field_valid & 2)) {
-fast_ata_pio:
- dma_func = ide_dma_off_quietly;
-no_dma_set:
- config_chipset_for_pio(drive);
+ if (pio == 255) {
+ piix_set_drive(drive, ide_find_best_mode(drive, XFER_PIO | XFER_EPIO));
+ return;
}
- return HWIF(drive)->dmaproc(dma_func, drive);
+
+ piix_set_drive(drive, XFER_PIO_0 + min_t(byte, pio, 5));
}

-static int piix_dmaproc(ide_dma_action_t func, ide_drive_t *drive)
+#ifdef CONFIG_BLK_DEV_IDEDMA
+
+/*
+ * piix_dmaproc() is a callback from upper layers that can do
+ * a lot, but we use it for DMA/PIO tuning only, delegating everything
+ * else to the default ide_dmaproc().
+ */
+
+int piix_dmaproc(ide_dma_action_t func, ide_drive_t *drive)
{
- switch (func) {
- case ide_dma_check:
- return config_drive_xfer_rate(drive);
- default :
- break;
+
+ if (func == ide_dma_check) {
+
+ short w80 = HWIF(drive)->udma_four;
+
+ short speed = ide_find_best_mode(drive,
+ XFER_PIO | XFER_EPIO | XFER_SWDMA | XFER_MWDMA |
+ (piix_config->flags & PIIX_UDMA ? XFER_UDMA : 0) |
+ (w80 && (piix_config->flags & PIIX_UDMA) >= PIIX_UDMA_66 ? XFER_UDMA_66 : 0) |
+ (w80 && (piix_config->flags & PIIX_UDMA) >= PIIX_UDMA_100 ? XFER_UDMA_100 : 0));
+
+ piix_set_drive(drive, speed);
+
+ func = (HWIF(drive)->autodma && (speed & XFER_MODE) != XFER_PIO)
+ ? ide_dma_on : ide_dma_off_quietly;
+
}
- /* Other cases are done by generic IDE-DMA code. */
+
return ide_dmaproc(func, drive);
}
-#endif /* defined(CONFIG_BLK_DEV_IDEDMA) && (CONFIG_PIIX_TUNING) */

-unsigned int __init pci_init_piix(struct pci_dev *dev)
+#endif /* CONFIG_BLK_DEV_IDEDMA */
+
+/*
+ * The initialization callback. Here we determine the IDE chip type
+ * and initialize its drive independent registers.
+ */
+
+unsigned int __init pci_init_piix(struct pci_dev *dev, const char *name)
{
-#if defined(DISPLAY_PIIX_TIMINGS) && defined(CONFIG_PROC_FS)
+ unsigned int u;
+ unsigned short w;
+ unsigned char t;
+ int i;
+
+/*
+ * Find out which Intel IDE this is.
+ */
+
+ for (piix_config = piix_ide_chips; piix_config->id; piix_config++)
+ if (dev->device == piix_config->id)
+ break;
+
+ if (!piix_config->id) {
+ printk(KERN_WARNING "PIIX: Unknown PIIX/ICH chip %#x, contact Vojtech Pavlik <vojtech@ucw.cz>\n", dev->device);
+ return -ENODEV;
+ }
+
+/*
+ * Check 80-wire cable presence.
+ */
+
+ switch (piix_config->flags & PIIX_UDMA) {
+
+ case PIIX_UDMA_66:
+ case PIIX_UDMA_100:
+ pci_read_config_dword(dev, PIIX_IDECFG, &u);
+ piix_80w = ((u & 0x30) ? 1 : 0) | ((u & 0xc0) ? 2 : 0);
+ break;
+
+ case PIIX_UDMA_V66:
+ pci_read_config_byte(dev, PIIX_IDESTAT, &t);
+ piix_80w = ((t & 2) ? 1 : 0) | ((t & 1) ? 2 : 0);
+ break;
+ }
+
+/*
+ * Enable ping-pong buffers where applicable.
+ */
+
+ if (piix_config->flags & PIIX_PINGPONG) {
+ pci_read_config_dword(dev, PIIX_IDECFG, &u);
+ u |= 0x400;
+ pci_write_config_dword(dev, PIIX_IDECFG, u);
+ }
+
+/*
+ * Detect enabled interfaces, enable slave separate timing if possible.
+ */
+
+ for (i = 0; i < 2; i++) {
+ pci_read_config_word(dev, PIIX_IDETIM0 + (i << 1), &w);
+ piix_enabled |= (w & 0x8000) ? (1 << i) : 0;
+ w &= 0x8c00;
+ if (~piix_config->flags & PIIX_NO_SITRE) w |= 0x4000;
+ w |= 0x44;
+ pci_write_config_word(dev, PIIX_IDETIM0 + (i << 1), w);
+ }
+
+/*
+ * Determine the system bus clock.
+ */
+
+ piix_clock = system_bus_speed * 1000;
+
+ switch (piix_clock) {
+ case 33000: piix_clock = 33333; break;
+ case 37000: piix_clock = 37500; break;
+ case 41000: piix_clock = 41666; break;
+ }
+
+ if (piix_clock < 20000 || piix_clock > 50000) {
+ printk(KERN_WARNING "PIIX: User given PCI clock speed impossible (%d), using 33 MHz instead.\n", piix_clock);
+ printk(KERN_WARNING "PIIX: Use ide0=ata66 if you want to assume 80-wire cable\n");
+ piix_clock = 33333;
+ }
+
+/*
+ * Print the boot message.
+ */
+
+ printk(KERN_INFO "PIIX: Intel %s IDE %s controller on pci%s\n",
+ piix_config->name, piix_dma[piix_config->flags & PIIX_UDMA], dev->slot_name);
+
+/*
+ * Register /proc/ide/piix entry
+ */
+
+#ifdef CONFIG_PROC_FS
if (!piix_proc) {
- piix_proc = 1;
+ piix_base = pci_resource_start(dev, 4);
bmide_dev = dev;
piix_display_info = &piix_get_info;
+ piix_proc = 1;
}
-#endif /* DISPLAY_PIIX_TIMINGS && CONFIG_PROC_FS */
+#endif
+
return 0;
}

-/*
- * Sheesh, someone at Intel needs to go read the ATA-4/5 T13 standards.
- * It does not specify device detection, but channel!!!
- * You determine later if bit 13 of word93 is set...
- */
-unsigned int __init ata66_piix (ide_hwif_t *hwif)
+unsigned int __init ata66_piix(ide_hwif_t *hwif)
{
- byte reg54h = 0, reg55h = 0, ata66 = 0;
- byte mask = hwif->channel ? 0xc0 : 0x30;
-
- pci_read_config_byte(hwif->pci_dev, 0x54, &reg54h);
- pci_read_config_byte(hwif->pci_dev, 0x55, &reg55h);
-
- ata66 = (reg54h & mask) ? 1 : 0;
-
- return ata66;
+ return ((piix_enabled & piix_80w) >> hwif->channel) & 1;
}

-void __init ide_init_piix (ide_hwif_t *hwif)
+void __init ide_init_piix(ide_hwif_t *hwif)
{
-#ifndef CONFIG_IA64
- if (!hwif->irq)
- hwif->irq = hwif->channel ? 15 : 14;
-#endif /* CONFIG_IA64 */
+ int i;

- if (hwif->pci_dev->device == PCI_DEVICE_ID_INTEL_82371MX) {
- /* This is a painful system best to let it self tune for now */
- return;
+ hwif->tuneproc = &piix_tune_drive;
+ hwif->speedproc = &piix_set_drive;
+ hwif->autodma = 0;
+
+ for (i = 0; i < 2; i++) {
+ hwif->drives[i].io_32bit = 1;
+ hwif->drives[i].unmask = 1;
+ hwif->drives[i].autotune = 1;
+ hwif->drives[i].dn = hwif->channel * 2 + i;
}

- hwif->tuneproc = &piix_tune_drive;
- hwif->drives[0].autotune = 1;
- hwif->drives[1].autotune = 1;
+#ifdef CONFIG_BLK_DEV_IDEDMA
+ if (hwif->dma_base) {
+ hwif->highmem = 1;
+ hwif->dmaproc = &piix_dmaproc;
+#ifdef CONFIG_IDEDMA_AUTO
+ if (!noautodma)
+ hwif->autodma = 1;
+#endif
+ }
+#endif /* CONFIG_BLK_DEV_IDEDMA */
+}

- if (!hwif->dma_base)
- return;
+/*
+ * We allow the BM-DMA driver only work on enabled interfaces.
+ */

- hwif->highmem = 1;
-#ifndef CONFIG_BLK_DEV_IDEDMA
- hwif->autodma = 0;
-#else /* CONFIG_BLK_DEV_IDEDMA */
-#ifdef CONFIG_PIIX_TUNING
- if (!noautodma)
- hwif->autodma = 1;
- hwif->dmaproc = &piix_dmaproc;
- hwif->speedproc = &piix_tune_chipset;
-#endif /* CONFIG_PIIX_TUNING */
-#endif /* !CONFIG_BLK_DEV_IDEDMA */
+void __init ide_dmacapable_piix(ide_hwif_t *hwif, unsigned long dmabase)
+{
+ if ((piix_enabled >> hwif->channel) & 1)
+ ide_setup_dma(hwif, dmabase, 8);
}
diff -urN linux-2.5.6-timing/drivers/ide/slc90e66.c linux-2.5.6-piix/drivers/ide/slc90e66.c
--- linux-2.5.6-timing/drivers/ide/slc90e66.c Tue Mar 12 16:26:03 2002
+++ linux-2.5.6-piix/drivers/ide/slc90e66.c Thu Jan 1 01:00:00 1970
@@ -1,384 +0,0 @@
-/*
- * linux/drivers/ide/slc90e66.c Version 0.10 October 4, 2000
- *
- * Copyright (C) 2000 Andre Hedrick <andre@linux-ide.org>
- * May be copied or modified under the terms of the GNU General Public License
- *
- * 00:07.1 IDE interface: EFAR Microsystems:
- * Unknown device 9130 (prog-if 8a [Master SecP PriP])
- * Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV-
- * VGASnoop- ParErr- Stepping- SERR- FastB2B-
- * Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium
- * >TAbort- <TAbort- <MAbort- >SERR- <PERR-
- * Latency: 64
- * Interrupt: pin A routed to IRQ 255
- * Region 4: I/O ports at 1050
- *
- * 00: 55 10 30 91 05 00 00 02 00 8a 01 01 00 40 00 00
- * 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
- * 20: 51 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00
- * 30: 00 00 00 00 00 00 00 00 00 00 00 00 ff 01 00 00
- * 40: 37 e3 33 e3 b9 55 01 00 0d 00 04 22 00 00 00 00
- * 50: 00 00 ff a0 00 00 00 08 40 00 00 00 00 00 00 00
- * 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
- * 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
- * 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
- * 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
- * a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
- * b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
- * c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
- * d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
- * e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
- * f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
- *
- * This a look-a-like variation of the ICH0 PIIX4 Ultra-66,
- * but this keeps the ISA-Bridge and slots alive.
- *
- */
-
-#include <linux/config.h>
-#include <linux/types.h>
-#include <linux/kernel.h>
-#include <linux/ioport.h>
-#include <linux/pci.h>
-#include <linux/hdreg.h>
-#include <linux/ide.h>
-#include <linux/delay.h>
-#include <linux/init.h>
-
-#include <asm/io.h>
-
-#include "ide-timing.h"
-
-#define SLC90E66_DEBUG_DRIVE_INFO 0
-
-#define DISPLAY_SLC90E66_TIMINGS
-
-#if defined(DISPLAY_SLC90E66_TIMINGS) && defined(CONFIG_PROC_FS)
-#include <linux/stat.h>
-#include <linux/proc_fs.h>
-
-static int slc90e66_get_info(char *, char **, off_t, int);
-extern int (*slc90e66_display_info)(char *, char **, off_t, int); /* ide-proc.c */
-static struct pci_dev *bmide_dev;
-
-static int slc90e66_get_info (char *buffer, char **addr, off_t offset, int count)
-{
- char *p = buffer;
- u32 bibma = pci_resource_start(bmide_dev, 4);
- u16 reg40 = 0, psitre = 0, reg42 = 0, ssitre = 0;
- u8 c0 = 0, c1 = 0;
- u8 reg44 = 0, reg47 = 0, reg48 = 0, reg4a = 0, reg4b = 0;
-
- pci_read_config_word(bmide_dev, 0x40, &reg40);
- pci_read_config_word(bmide_dev, 0x42, &reg42);
- pci_read_config_byte(bmide_dev, 0x44, &reg44);
- pci_read_config_byte(bmide_dev, 0x47, &reg47);
- pci_read_config_byte(bmide_dev, 0x48, &reg48);
- pci_read_config_byte(bmide_dev, 0x4a, &reg4a);
- pci_read_config_byte(bmide_dev, 0x4b, &reg4b);
-
- psitre = (reg40 & 0x4000) ? 1 : 0;
- ssitre = (reg42 & 0x4000) ? 1 : 0;
-
- /*
- * at that point bibma+0x2 et bibma+0xa are byte registers
- * to investigate:
- */
-#ifdef __mips__ /* only for mips? */
- c0 = inb_p(bibma + 0x02);
- c1 = inb_p(bibma + 0x0a);
-#else
- c0 = inb_p((unsigned short)bibma + 0x02);
- c1 = inb_p((unsigned short)bibma + 0x0a);
-#endif
-
- p += sprintf(p, " SLC90E66 Chipset.\n");
- p += sprintf(p, "--------------- Primary Channel ---------------- Secondary Channel -------------\n");
- p += sprintf(p, " %sabled %sabled\n",
- (c0&0x80) ? "dis" : " en",
- (c1&0x80) ? "dis" : " en");
- p += sprintf(p, "--------------- drive0 --------- drive1 -------- drive0 ---------- drive1 ------\n");
- p += sprintf(p, "DMA enabled: %s %s %s %s\n",
- (c0&0x20) ? "yes" : "no ",
- (c0&0x40) ? "yes" : "no ",
- (c1&0x20) ? "yes" : "no ",
- (c1&0x40) ? "yes" : "no " );
- p += sprintf(p, "UDMA enabled: %s %s %s %s\n",
- (reg48&0x01) ? "yes" : "no ",
- (reg48&0x02) ? "yes" : "no ",
- (reg48&0x04) ? "yes" : "no ",
- (reg48&0x08) ? "yes" : "no " );
- p += sprintf(p, "UDMA enabled: %s %s %s %s\n",
- ((reg4a&0x04)==0x04) ? "4" :
- ((reg4a&0x03)==0x03) ? "3" :
- (reg4a&0x02) ? "2" :
- (reg4a&0x01) ? "1" :
- (reg4a&0x00) ? "0" : "X",
- ((reg4a&0x40)==0x40) ? "4" :
- ((reg4a&0x30)==0x30) ? "3" :
- (reg4a&0x20) ? "2" :
- (reg4a&0x10) ? "1" :
- (reg4a&0x00) ? "0" : "X",
- ((reg4b&0x04)==0x04) ? "4" :
- ((reg4b&0x03)==0x03) ? "3" :
- (reg4b&0x02) ? "2" :
- (reg4b&0x01) ? "1" :
- (reg4b&0x00) ? "0" : "X",
- ((reg4b&0x40)==0x40) ? "4" :
- ((reg4b&0x30)==0x30) ? "3" :
- (reg4b&0x20) ? "2" :
- (reg4b&0x10) ? "1" :
- (reg4b&0x00) ? "0" : "X");
-
- p += sprintf(p, "UDMA\n");
- p += sprintf(p, "DMA\n");
- p += sprintf(p, "PIO\n");
-
-/*
- * FIXME.... Add configuration junk data....blah blah......
- */
-
- return p-buffer; /* => must be less than 4k! */
-}
-#endif /* defined(DISPLAY_SLC90E66_TIMINGS) && defined(CONFIG_PROC_FS) */
-
-/*
- * Used to set Fifo configuration via kernel command line:
- */
-
-byte slc90e66_proc = 0;
-
-extern char *ide_xfer_verbose (byte xfer_rate);
-
-#ifdef CONFIG_BLK_DEV_IDEDMA
-/*
- *
- */
-static byte slc90e66_dma_2_pio (byte xfer_rate) {
- switch(xfer_rate) {
- case XFER_UDMA_4:
- case XFER_UDMA_3:
- case XFER_UDMA_2:
- case XFER_UDMA_1:
- case XFER_UDMA_0:
- case XFER_MW_DMA_2:
- case XFER_PIO_4:
- return 4;
- case XFER_MW_DMA_1:
- case XFER_PIO_3:
- return 3;
- case XFER_SW_DMA_2:
- case XFER_PIO_2:
- return 2;
- case XFER_MW_DMA_0:
- case XFER_SW_DMA_1:
- case XFER_SW_DMA_0:
- case XFER_PIO_1:
- case XFER_PIO_0:
- case XFER_PIO_SLOW:
- default:
- return 0;
- }
-}
-#endif /* CONFIG_BLK_DEV_IDEDMA */
-
-/*
- * Based on settings done by AMI BIOS
- * (might be useful if drive is not registered in CMOS for any reason).
- */
-static void slc90e66_tune_drive (ide_drive_t *drive, byte pio)
-{
- unsigned long flags;
- u16 master_data;
- byte slave_data;
- int is_slave = (&HWIF(drive)->drives[1] == drive);
- int master_port = HWIF(drive)->index ? 0x42 : 0x40;
- int slave_port = 0x44;
- /* ISP RTC */
- byte timings[][2] = { { 0, 0 },
- { 0, 0 },
- { 1, 0 },
- { 2, 1 },
- { 2, 3 }, };
-
- if (pio == 255)
- pio = ide_find_best_mode(drive, XFER_PIO | XFER_EPIO) - XFER_PIO_0;
- else
- pio = min_t(byte, pio, 4);
-
- pci_read_config_word(HWIF(drive)->pci_dev, master_port, &master_data);
- if (is_slave) {
- master_data = master_data | 0x4000;
- if (pio > 1)
- /* enable PPE, IE and TIME */
- master_data = master_data | 0x0070;
- pci_read_config_byte(HWIF(drive)->pci_dev, slave_port, &slave_data);
- slave_data = slave_data & (HWIF(drive)->index ? 0x0f : 0xf0);
- slave_data = slave_data | ((timings[pio][0] << 2) | (timings[pio][1]
- << (HWIF(drive)->index ? 4 : 0)));
- } else {
- master_data = master_data & 0xccf8;
- if (pio > 1)
- /* enable PPE, IE and TIME */
- master_data = master_data | 0x0007;
- master_data = master_data | (timings[pio][0] << 12) |
- (timings[pio][1] << 8);
- }
- save_flags(flags);
- cli();
- pci_write_config_word(HWIF(drive)->pci_dev, master_port, master_data);
- if (is_slave)
- pci_write_config_byte(HWIF(drive)->pci_dev, slave_port, slave_data);
- restore_flags(flags);
-}
-
-#ifdef CONFIG_BLK_DEV_IDEDMA
-static int slc90e66_tune_chipset (ide_drive_t *drive, byte speed)
-{
- ide_hwif_t *hwif = HWIF(drive);
- struct pci_dev *dev = hwif->pci_dev;
- byte maslave = hwif->channel ? 0x42 : 0x40;
- int a_speed = 7 << (drive->dn * 4);
- int u_flag = 1 << drive->dn;
- int u_speed = 0;
- int err = 0;
- int sitre;
- short reg4042, reg44, reg48, reg4a;
-
- pci_read_config_word(dev, maslave, &reg4042);
- sitre = (reg4042 & 0x4000) ? 1 : 0;
- pci_read_config_word(dev, 0x44, &reg44);
- pci_read_config_word(dev, 0x48, &reg48);
- pci_read_config_word(dev, 0x4a, &reg4a);
-
- switch(speed) {
- case XFER_UDMA_4: u_speed = 4 << (drive->dn * 4); break;
- case XFER_UDMA_3: u_speed = 3 << (drive->dn * 4); break;
- case XFER_UDMA_2: u_speed = 2 << (drive->dn * 4); break;
- case XFER_UDMA_1: u_speed = 1 << (drive->dn * 4); break;
- case XFER_UDMA_0: u_speed = 0 << (drive->dn * 4); break;
- case XFER_MW_DMA_2:
- case XFER_MW_DMA_1:
- case XFER_SW_DMA_2: break;
-#if 0 /* allow PIO modes */
- default: return -1;
-#endif
- }
-
- if (speed >= XFER_UDMA_0) {
- if (!(reg48 & u_flag))
- pci_write_config_word(dev, 0x48, reg48|u_flag);
- if ((reg4a & u_speed) != u_speed) {
- pci_write_config_word(dev, 0x4a, reg4a & ~a_speed);
- pci_read_config_word(dev, 0x4a, &reg4a);
- pci_write_config_word(dev, 0x4a, reg4a|u_speed);
- }
- }
- if (speed < XFER_UDMA_0) {
- if (reg48 & u_flag)
- pci_write_config_word(dev, 0x48, reg48 & ~u_flag);
- if (reg4a & a_speed)
- pci_write_config_word(dev, 0x4a, reg4a & ~a_speed);
- }
-
- slc90e66_tune_drive(drive, slc90e66_dma_2_pio(speed));
-
-#if SLC90E66_DEBUG_DRIVE_INFO
- printk("%s: %s drive%d\n", drive->name, ide_xfer_verbose(speed), drive->dn);
-#endif /* SLC90E66_DEBUG_DRIVE_INFO */
- if (!drive->init_speed)
- drive->init_speed = speed;
- err = ide_config_drive_speed(drive, speed);
- drive->current_speed = speed;
- return err;
-}
-
-static int slc90e66_config_drive_for_dma (ide_drive_t *drive)
-{
- struct hd_driveid *id = drive->id;
- int ultra = 1;
- byte speed = 0;
- byte udma_66 = eighty_ninty_three(drive);
-
-#if 1 /* allow PIO modes */
- if (!HWIF(drive)->autodma) {
- speed = ide_find_best_mode(drive, XFER_PIO | XFER_EPIO);
- (void) slc90e66_tune_chipset(drive, speed);
- return ((int) ide_dma_off_quietly);
- }
-#endif
-
- speed = ide_find_best_mode(drive, XFER_PIO | XFER_EPIO | XFER_SWDMA | XFER_MWDMA
- | (ultra ? XFER_UDMA : 0) | ((ultra && udma_66) ? XFER_UDMA_66 : 0));
-
- (void) slc90e66_tune_chipset(drive, speed);
-
- return ((int) ((id->dma_ultra >> 11) & 7) ? ide_dma_on :
- ((id->dma_ultra >> 8) & 7) ? ide_dma_on :
- ((id->dma_mword >> 8) & 7) ? ide_dma_on :
- ((id->dma_1word >> 8) & 7) ? ide_dma_on :
- ide_dma_off_quietly);
-}
-
-static int slc90e66_dmaproc(ide_dma_action_t func, ide_drive_t *drive)
-{
- switch (func) {
- case ide_dma_check:
- return ide_dmaproc((ide_dma_action_t) slc90e66_config_drive_for_dma(drive), drive);
- default :
- break;
- }
- /* Other cases are done by generic IDE-DMA code. */
- return ide_dmaproc(func, drive);
-}
-#endif /* CONFIG_BLK_DEV_IDEDMA */
-
-unsigned int __init pci_init_slc90e66(struct pci_dev *dev)
-{
-#if defined(DISPLAY_SLC90E66_TIMINGS) && defined(CONFIG_PROC_FS)
- if (!slc90e66_proc) {
- slc90e66_proc = 1;
- bmide_dev = dev;
- slc90e66_display_info = &slc90e66_get_info;
- }
-#endif /* DISPLAY_SLC90E66_TIMINGS && CONFIG_PROC_FS */
- return 0;
-}
-
-unsigned int __init ata66_slc90e66 (ide_hwif_t *hwif)
-{
-#if 1
- byte reg47 = 0, ata66 = 0;
- byte mask = hwif->channel ? 0x01 : 0x02; /* bit0:Primary */
-
- pci_read_config_byte(hwif->pci_dev, 0x47, &reg47);
-
- ata66 = (reg47 & mask) ? 0 : 1; /* bit[0(1)]: 0:80, 1:40 */
-#else
- byte ata66 = 0;
-#endif
- return ata66;
-}
-
-void __init ide_init_slc90e66 (ide_hwif_t *hwif)
-{
- if (!hwif->irq)
- hwif->irq = hwif->channel ? 15 : 14;
-
- hwif->tuneproc = &slc90e66_tune_drive;
- hwif->drives[0].autotune = 1;
- hwif->drives[1].autotune = 1;
-
- if (!hwif->dma_base)
- return;
-
- hwif->autodma = 0;
- hwif->highmem = 1;
-#ifdef CONFIG_BLK_DEV_IDEDMA
- if (!noautodma)
- hwif->autodma = 1;
- hwif->dmaproc = &slc90e66_dmaproc;
- hwif->speedproc = &slc90e66_tune_chipset;
-#endif /* !CONFIG_BLK_DEV_IDEDMA */
-}
\
 
 \ /
  Last update: 2005-03-22 13:25    [W:2.903 / U:0.020 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site