Messages in this thread | | | Date | Wed, 05 Jul 2000 22:52:51 +0200 | From | octave klaba <> | Subject | is there any kernel panic there ? |
| |
Hi, An another servers crashed running on 2.2.15 with raid-soft
the output of the servers' consoles is logged on a separated box thought serial cable and I have nothight the logs except the "\n" and the server is no more pingable. I can not log thought serial, can not log directly. Just hard reset.
Have you any idea where should I seek the error ? Why there is no kernel panic ?
Thx Octave
Linux version 2.2.15 (root@XXXXXXXXXXXX) (gcc version egcs-2.91.66 19990314/Linux (egcs-1.1.2 release)) #1 Sun May 28 01:36:47 CEST 2000 Detected 451026999 Hz processor. Console: colour VGA+ 80x25 Calibrating delay loop... 897.84 BogoMIPS Memory: 387604k/393152k available (1008k kernel code, 408k reserved, 4092k data, 40k init) Dentry hash table entries: 65536 (order 7, 512k) Buffer cache hash table entries: 524288 (order 9, 2048k) Page cache hash table entries: 131072 (order 7, 512k) VFS: Diskquotas version dquot_6.4.0 initialized CPU: Intel Pentium III (Katmai) stepping 03 Checking 386/387 coupling... OK, FPU using exception 16 error reporting. Checking 'hlt' instruction... OK. POSIX conformance testing by UNIFIX mtrr: v1.35a (19990819) Richard Gooch (rgooch@atnf.csiro.au) PCI: PCI BIOS revision 2.10 entry at 0xf08b0 PCI: Using configuration type 1 PCI: Probing PCI hardware Linux NET4.0 for Linux 2.2 Based upon Swansea University Computer Society NET3.039 NET4: Unix domain sockets 1.0 for Linux NET4.0. NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP TCP: Hash tables configured (ehash 524288 bhash 65536) Starting kswapd v 1.5 Detected PS/2 Mouse Port. Serial driver version 4.27 with<4>keyboard: Too many NACKs -- noisy kbd cable? keyboard: Too many NACKs -- noisy kbd cable? no serial options enabled ttyS00 at 0x03f8 (irq = 4) is a 16550A ttyS01 at 0x02f8 (irq = 3) is a 16550A pty: 256 Unix98 ptys configured Real Time Clock Driver v1.09 PIIX4: IDE controller on PCI bus 00 dev 21 PIIX4: not 100% native mode: will probe irqs later ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:pio, hdd:pio hda: IBM-DJNA-371800, ATA DISK drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 hda: IBM-DJNA-371800, 17206MB w/1966kB Cache, CHS=2193/255/63, UDMA floppy0: no floppy controllers found md driver 0.90.0 MAX_MD_DEVS=256, MAX_REAL=12 raid1 personality registered (scsi0) <Adaptec AHA-294X Ultra2 SCSI host adapter> found at PCI 0/12/0 (scsi0) Wide Channel, SCSI ID=7, 32/255 SCBs (scsi0) Downloading sequencer code... 396 instructions downloaded scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.28/3.2.4 <Adaptec AHA-294X Ultra2 SCSI host adapter> scsi : 1 host. (scsi0:0:0:0) Synchronous at 40.0 Mbyte/sec, offset 31. Vendor: IBM Model: DNES-318350W Rev: SA30 Type: Direct-Access ANSI SCSI revision: 03 Detected scsi disk sda at scsi0, channel 0, id 0, lun 0 (scsi0:0:1:0) Synchronous at 40.0 Mbyte/sec, offset 31. Vendor: IBM Model: DNES-318350W Rev: SA30 Type: Direct-Access ANSI SCSI revision: 03 Detected scsi disk sdb at scsi0, channel 0, id 1, lun 0 scsi : detected 2 SCSI disks total. SCSI device sda: hdwr sector= 512 bytes. Sectors= 35843670 [17501 MB] [17.5 GB] SCSI device sdb: hdwr sector= 512 bytes. Sectors= 35843670 [17501 MB] [17.5 GB] 3c59x.c:v0.99H 11/17/98 Donald Becker http://cesdis.gsfc.nasa.gov/linux/drivers/vortex.html eth0: 3Com 3c905B Cyclone 100baseTx at 0xd000, 00:01:02:06:d2:54, IRQ 10 8K byte-wide RAM 5:3 Rx:Tx split, autoselect/Autonegotiate interface. MII transceiver found at address 24, status 786d. MII transceiver found at address 0, status 786d. Enabling bus-master transmits and whole-frame receives. Partition check: sda: sda1 sda2 sdb: sdb1 sdb2 md.c: sizeof(mdp_super_t) = 4096 hda: hda1 hda2 < hda5 hda6 > autodetecting RAID arrays (read) sda2's sb offset: 17526848 [events: 00000009] (read) sdb2's sb offset: 17526848 [events: 00000009] autorun ... considering sdb2 ... adding sdb2 ... adding sda2 ... created md0 bind<sda2,1> bind<sdb2,2> running: <sdb2><sda2> now! sdb2's event counter: 00000009 sda2's event counter: 00000009 md: md0: raid array is not clean -- starting background reconstruction md0: max total readahead window set to 128k md0: 1 data-disks, max readahead per data-disk: 128k raid1: device sdb2 operational as mirror 1 raid1: device sda2 operational as mirror 0 raid1: raid set md0 not clean; reconstructing mirrors raid1: raid set md0 active with 2 out of 2 mirrors md: updating md0 RAID superblock on device sdb2 [events: 0000000a](write) sdb2's sb offset: 17526848 md: syncing RAID array md0 md: minimum _guaranteed_ reconstruction speed: 100 KB/sec. md: using maximum available idle IO bandwith for reconstruction. md: using 128k window. sda2 [events: 0000000a](write) sda2's sb offset: 17526848 . ... autorun DONE. VFS: Mounted root (ext2 filesystem) readonly. Freeing unused kernel memory: 40k freed Adding Swap: 393552k swap-space (priority -1) Adding Swap: 393552k swap-space (priority -2) md: md0: sync done. i2c-core.o: i2c core module piix4.o version 2.5.0 (20000312) i2c-core.o: adapter SMBus PIIX4 adapter at e800 registered as adapter 0. i2c-piix4.o: PIIX4 bus detected and initialized sensors.o version 2.5.0 (20000312) w83781d.o version 2.5.0 (20000312) i2c-core.o: driver W83781D sensor driver registered. i2c-core.o: client [AS99127F chip] registered to adapter [SMBus PIIX4 adapter at e800](pos. 0). i2c-core.o: client [AS99127F subclient] registered to adapter [SMBus PIIX4 adapter at e800](pos. 1). i2c-core.o: client [AS99127F subclient] registered to adapter [SMBus PIIX4 adapter at e800](pos. 2).
- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.rutgers.edu Please read the FAQ at http://www.tux.org/lkml/
| |