Messages in this thread |  | | Date | Sat, 30 Dec 2000 23:24:40 +0000 (GMT) | From | davej@suse ... | Subject | Problems with ov511/USB on test13-pre7 |
| |
Hi,
Problems with Creative Webcam III. This worked fine in test13-pre4, haven't tried pre5 & 6.
On boot:
usb_control/bulk_msg: timeout usb_control/bulk_msg: timeout usb.c: couldn't get all of config descriptors usb.c: unable to get device 2 configuration (error=-110) hub.c: USB new device connect on bus1/1, assigned device number 4 usb_control/bulk_msg: timeout usb.c: USB device not accepting new address=4 (error=-110)
On remove/reinsert:
hub.c: USB new device connect on bus1/1, assigned device number 5 usb_control/bulk_msg: timeout usb.c: USB device not accepting new address=5 (error=-110) hub.c: USB new device connect on bus1/1, assigned device number 6 usb_control/bulk_msg: timeout usb.c: USB device not accepting new address=6 (error=-110)
USB controller is:
00:04.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 10) (prog-if 00 [UHCI]) Subsystem: Unknown device 0925:1234 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32, cache line size 08 Interrupt: pin D routed to IRQ 5 Region 4: I/O ports at d400 [size=32] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
The only other thing of relevance in dmesg, is the flood of irq warnings related to the two USB controllers on 4.2 & 4.3 :-
PCI: Found IRQ 5 for device 00:09.0 PCI: The same IRQ used for device 00:04.2 PCI: The same IRQ used for device 00:04.3 PCI: Found IRQ 5 for device 00:04.2 PCI: The same IRQ used for device 00:04.3 PCI: The same IRQ used for device 00:09.0 PCI: Found IRQ 5 for device 00:04.3 PCI: The same IRQ used for device 00:04.2 PCI: The same IRQ used for device 00:09.0 usb-uhci.c: USB UHCI at I/O 0xd000, IRQ 5 usb-uhci.c: Detected 2 ports hub.c: USB new device connect on bus1/1, assigned device number 2 usb.c: new USB bus registered, assigned bus number 2 usb-uhci.c: interrupt, status 2, frame# 135 hub.c: USB hub found hub.c: 2 ports detected usb.c: registered new driver ov511 ov511.c: ov511 driver version 1.28 registered
regards,
Davej.
-- | Dave Jones. http://www.suse.de/~davej | SuSE Labs
- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.kernel.org Please read the FAQ at http://www.tux.org/lkml/
|  |