lkml.org 
[lkml]   [1999]   [Jan]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
Subject2.2.0 pre5-ac1 tulip.c
<!doctype html public "-//w3c//dtd html 4.0 transitional//en">
<html>
&nbsp;
<br>&nbsp;
<pre>I have a linksys&nbsp; etherfast 10/100.

using dhcp with a cable modem for @home

Works under 2.0.36&nbsp; but not 2.2.0-pre4-ac1</pre>

<pre>Any clues?</pre>

<pre></pre>
For 2.0.36
<br>klogd report as:
<p>tulip.c:v0.89H 5/23/98 becker@cesdis.gsfc.nasa.gov
<br>eth0: Lite-On 82c168 PNIC at 0xec00, 00 a0 cc 22 28 0a, IRQ 5.
<br>eth0:&nbsp; MII transceiver found at MDIO address 1, config 3100 status
7829.
<br>eth0:&nbsp; Advertising 01e1 on PHY 1, previously advertising 01e1.
<p>eth0: Changing PNIC configuration to half-duplex, CSR6 816e0000
<p>using tulip-diag.c :
<p>tulip-diag.c:v1.06 9/18/98 Donald Becker (becker@cesdis.gsfc.nasa.gov)
<br>Digital DC21040 Tulip Tulip chip registers at 0xec00:
<br>&nbsp; 00008000 01ff0000 01000608 00459028 00459228 02660010 816e2002
0001ebef
<br>&nbsp; 00000000 00000000 00459228 0045b60c 00000025 00000000 00000000
10000001
<br>&nbsp;The Rx process state is 'Waiting for packets'.
<br>&nbsp;The Tx process state is 'Idle'.
<br>Transmit started, Receive started, half-duplex.
<br>&nbsp;The transmit unit is set to store-and-forward.
<br>&nbsp;Port selection is MII 100baseTx scrambler, half-duplex.
<p>2.2.0-pre5-ac1
<p>tulip.c:v0.89H 5/23/98 becker@cesdis.gsfc.nasa.gov
<br>eth0: Lite-On 82c168 PNIC at 0xec00, 00 a0 cc 22 28 0a, IRQ 5.
<br>eth0:&nbsp; MII transceiver found at MDIO address 1, config 3100 status
7829.
<br>eth0:&nbsp; Advertising 01e1 on PHY 1, previously advertising 01e1.
<p>etho: Using DHCP failed.
<p>tulip-diag.c:v1.06 9/18/98 Donald Becker (becker@cesdis.gsfc.nasa.gov)
<br>Digital DC21040 Tulip Tulip chip registers at 0xec00:
<br>&nbsp; 00000000 01ff0000 0008ffff 00000000 00000000 02000112 01440040
00000000
<br>&nbsp; 00000000 00000000 00000000 00000000 00000025 00000000 00000000
10000000
<br>&nbsp;The Rx process state is 'Stopped'.
<br>&nbsp;The Tx process state is 'Stopped'.
<br>Transmit stopped, Receive stopped, half-duplex.
<br>&nbsp;The transmit threshold is 72.
<br>&nbsp;Port selection is MII 100baseTx scrambler, half-duplex.
<br>&nbsp;
<br>&nbsp;
<br>&nbsp;</html>
\
 
 \ /
  Last update: 2005-03-22 13:49    [W:0.047 / U:0.084 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site