Messages in this thread | | | Date | Fri, 24 Apr 1998 14:32:39 -0500 (CDT) | From | Bobby <> | Subject | aic7xxx problems |
| |
Greets..
Hope this message finds you all well..
Since 2.1.96, I've had problems with the aic7xxx drivers. 2.1.95 and earlier will communicate with my hard drive, while 2.1.96 and above will not.. Here is the excerpt from my boot messages for 2.1.97, with (apparently new) aic7xxx drivers from 2.1.97 source tree (same kind of thing happens with 2.1.98, with 2.1.98's original drivers):
hda: IBM-DAQA-33240, ATA DISK drive hdb: ST5660A, ATA DISK drive hdc: CD-532E, ATAPI CDROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 ide1 at 0x170-0x177,0x376 on irq 15 hda: IBM-DAQA-33240, 3098MB w/96kB Cache, CHS=787/128/63 hdb: ST5660A, 504MB w/256kB Cache, CHS=512/32/63 (scsi0) <Adaptec AHA-294X Ultra SCSI host adapter> found at PCI 10/0 (scsi0) Wide Channel, SCSI ID=7, 16/255 SCBs (scsi0) BIOS enabled, IO Port 0x6000, IRQ 9 (scsi0) IO Memory at 0xe1804000, MMAP Memory at 0xc6800000 (scsi0) Resetting channel (scsi0) Downloading sequencer code... 413 instructions downloaded scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.0.13/3.2.4 <Adaptec AHA-294X Ultra SCSI host adapter> scsi : 1 host. (scsi0:0:-1:-1) Scanning channel for devices. scsi0 : channel 0 target 1 lun 0 request sense failed, performing reset. SCSI bus is being reset for host 0 channel 0. scsi : detected total. Partition check: hda: hda1 hda2 hda3 hda4 hdb: hdb1
And below is the same section from 2.1.98 with the scsi drivers from 2.1.95, same config:
aic7xxx: <Adaptec AHA-294X Ultra SCSI host adapter> at PCI 10 aic7xxx: BIOS enabled, IO Port 0x6000, IO Mem 0xe1804000, IRQ 9, Revision B aic7xxx: Wide Channel, SCSI ID 7, 16/16 SCBs, QFull 16, QMask 0x1f scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 4.1/3.2 scsi : 1 host. scsi0: Scanning channel A for devices. Vendor: MICROP Model: 2217-15MZ1001905 Rev: HQ30 Type: Direct-Access ANSI SCSI revision: 02 Detected scsi disk sda at scsi0, channel 0, id 1, lun 0 scsi : detected 1 SCSI disk total. SCSI device sda: hdwr sector= 512 bytes. Sectors= 3450902 [1685 MB] [1.7 GB] Partition check: sda: sda1 sda2 sda3 hda: hda1 hda2 hda3 hda4 hdb: hdb1
If someone can help me figure out what is either wrong with my setup or what I need to do to my hardware to get the new aic7xxx drivers working with my hardware, they will have my undying admiration until the end of Time...
Thanks!
+=+=+=+=+=+=+=+=+=+=+=+=+ | bobby@mezaway.org |
- To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to majordomo@vger.rutgers.edu
| |