lkml.org 
[lkml]   [2018]   [Dec]   [24]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH] ASoC: sgtl5000: Allow SCLK pad drive strength to be changed
Date
This patch introduces "sclk-strength" property to allow SCLK pad drive
strength to be changed via device tree.

When running playback test on LS1028ARDB, Tx Frame sync error interrupt
will occur sometimes. Some noises also exist. After changing SCLK pad
drive strength to the maximum value, the issues are gone.

Signed-off-by: Alison Wang <alison.wang@nxp.com>
---
sound/soc/codecs/sgtl5000.c | 19 ++++++++++++++++++-
1 files changed, 18 insertions(+), 1 deletions(-)

diff --git a/sound/soc/codecs/sgtl5000.c b/sound/soc/codecs/sgtl5000.c
index add18d6..a6a4748 100644
--- a/sound/soc/codecs/sgtl5000.c
+++ b/sound/soc/codecs/sgtl5000.c
@@ -116,6 +116,13 @@ enum {
I2S_LRCLK_STRENGTH_HIGH,
};

+enum {
+ I2S_SCLK_STRENGTH_DISABLE,
+ I2S_SCLK_STRENGTH_LOW,
+ I2S_SCLK_STRENGTH_MEDIUM,
+ I2S_SCLK_STRENGTH_HIGH,
+};
+
/* sgtl5000 private structure in codec */
struct sgtl5000_priv {
int sysclk; /* sysclk rate */
@@ -129,6 +136,7 @@ struct sgtl5000_priv {
u8 micbias_resistor;
u8 micbias_voltage;
u8 lrclk_strength;
+ u8 sclk_strength;
};

/*
@@ -1302,7 +1310,9 @@ static int sgtl5000_probe(struct snd_soc_component *component)
SGTL5000_DAC_MUTE_RIGHT |
SGTL5000_DAC_MUTE_LEFT);

- reg = ((sgtl5000->lrclk_strength) << SGTL5000_PAD_I2S_LRCLK_SHIFT | 0x5f);
+ reg = ((sgtl5000->lrclk_strength) << SGTL5000_PAD_I2S_LRCLK_SHIFT |
+ (sgtl5000->sclk_strength) << SGTL5000_PAD_I2S_SCLK_SHIFT |
+ 0x1f);
snd_soc_component_write(component, SGTL5000_CHIP_PAD_STRENGTH, reg);

snd_soc_component_write(component, SGTL5000_CHIP_ANA_CTRL,
@@ -1542,6 +1552,13 @@ static int sgtl5000_i2c_probe(struct i2c_client *client,
sgtl5000->lrclk_strength = value;
}

+ sgtl5000->sclk_strength = I2S_SCLK_STRENGTH_LOW;
+ if (!of_property_read_u32(np, "sclk-strength", &value)) {
+ if (value > I2S_SCLK_STRENGTH_HIGH)
+ value = I2S_SCLK_STRENGTH_LOW;
+ sgtl5000->sclk_strength = value;
+ }
+
/* Ensure sgtl5000 will start with sane register values */
sgtl5000_fill_defaults(client);

--
1.7.1
\
 
 \ /
  Last update: 2018-12-24 08:48    [W:0.314 / U:0.076 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site