lkml.org 
[lkml]   [2017]   [May]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH] dt-bindings: power: New bindings for ltc3651-charger
From
Date
On 08-05-17 19:12, Rob Herring wrote:
> On Fri, May 05, 2017 at 08:38:35AM +0200, Mike Looijmans wrote:
>> This adds the devicetree bindings documentation for the LTC3651 battery charger.
>>
>> Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
>> ---
>> .../bindings/power/supply/ltc3651-charger.txt | 26 ++++++++++++++++++++++
>> 1 file changed, 26 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/power/supply/ltc3651-charger.txt
>>
>> diff --git a/Documentation/devicetree/bindings/power/supply/ltc3651-charger.txt b/Documentation/devicetree/bindings/power/supply/ltc3651-charger.txt
>> new file mode 100644
>> index 0000000..a7dd80f
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/power/supply/ltc3651-charger.txt
>> @@ -0,0 +1,26 @@
>> +ltc3651-charger
>> +
>> +Required properties:
>> + - compatible: "lltc,ltc3651-charger"
>> + - acpr-gpios: Connect to ACPR output. See remark below.
>> +
>> +Optional properties:
>> + - fault-gpios: Connect to FAULT output. See remark below.
>> + - chrg-gpios: Connect to CHRG output. See remark below.
>
> All the gpios need vendor prefix.

Will prefix "lltc," adjust the driver and submit new patches.

>
>> +
>> +The ltc3651 outputs are open-drain type and active low. The driver assumes the
>> +GPIO reports "active" when the output is asserted, so if the pins have been
>> +connected directly, the GPIO flags should be set to active low also.
>> +
>> +The driver will attempt to aquire interrupts for all GPIOs. If the system is
>> +not capabale of providing that, the driver cannot report changes and userspace
>> +will need to periodically read the sysfs attributes to detect changes.
>
> If these are interrupts, then you should use the interrupt binding
> instead (most GPIO controllers are also interrupt controllers).

They're GPIO (the driver needs the current state), the use of interrupts is
just to detect changes. Similar to gpio-charger for example. Interrupt
bindings cannot provide the current state of the line.


>
>> +
>> +Example:
>> +
>> + charger: battery-charger {
>> + compatible = "lltc,ltc3651-charger";
>> + acpr-gpios = <&gpio0 68 GPIO_ACTIVE_LOW>;
>> + fault-gpios = <&gpio0 64 GPIO_ACTIVE_LOW>;
>> + chrg-gpios = <&gpio0 63 GPIO_ACTIVE_LOW>;
>> + };
>> --
>> 1.9.1
>>



Kind regards,

Mike Looijmans
System Expert

TOPIC Products
Materiaalweg 4, NL-5681 RJ Best
Postbus 440, NL-5680 AK Best
Telefoon: +31 (0) 499 33 69 79
E-mail: mike.looijmans@topicproducts.com
Website: www.topicproducts.com

Please consider the environment before printing this e-mail





\
 
 \ /
  Last update: 2017-05-10 21:17    [W:0.091 / U:0.276 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site