lkml.org 
[lkml]   [2017]   [Dec]   [22]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 3/4] extcon: axp288: Redo charger type dection a couple of seconds after probe()
Date
The axp288 extcon code depends on other drivers to do things like mux the
data lines, enable/disable vbus based on the id-pin, etc.

Sometimes the BIOS has not set these things up correctly resulting in the
initial charger cable type detection giving a wrong result and we end up
not charging or charging at only 0.5A.

This commit starts a second charger-detection cycle a couple of seconds
after the first one finishes, giving the other drivers time to load and
do their thing.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
---
drivers/extcon/extcon-axp288.c | 32 ++++++++++++++++++++++++++++++--
1 file changed, 30 insertions(+), 2 deletions(-)

diff --git a/drivers/extcon/extcon-axp288.c b/drivers/extcon/extcon-axp288.c
index 386afb7d1160..cc7c35c7ff02 100644
--- a/drivers/extcon/extcon-axp288.c
+++ b/drivers/extcon/extcon-axp288.c
@@ -1,6 +1,7 @@
/*
* extcon-axp288.c - X-Power AXP288 PMIC extcon cable detection driver
*
+ * Copyright (C) 2016-2017 Hans de Goede <hdegoede@redhat.com>
* Copyright (C) 2015 Intel Corporation
* Author: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
*
@@ -97,9 +98,11 @@ struct axp288_extcon_info {
struct device *dev;
struct regmap *regmap;
struct regmap_irq_chip_data *regmap_irqc;
+ struct delayed_work det_work;
int irq[EXTCON_IRQ_END];
struct extcon_dev *edev;
unsigned int previous_cable;
+ bool first_detect_done;
};

/* Power up/down reason string array */
@@ -137,6 +140,25 @@ static void axp288_extcon_log_rsi(struct axp288_extcon_info *info)
regmap_write(info->regmap, AXP288_PS_BOOT_REASON_REG, clear_mask);
}

+static void axp288_chrg_detect_complete(struct axp288_extcon_info *info)
+{
+ /*
+ * We depend on other drivers to do things like mux the data lines,
+ * enable/disable vbus based on the id-pin, etc. Sometimes the BIOS has
+ * not set these things up correctly resulting in the initial charger
+ * cable type detection giving a wrong result and we end up not charging
+ * or charging at only 0.5A.
+ *
+ * So we schedule a second cable type detection after 2 seconds to
+ * give the other drivers time to load and do their thing.
+ */
+ if (!info->first_detect_done) {
+ queue_delayed_work(system_wq, &info->det_work,
+ msecs_to_jiffies(2000));
+ info->first_detect_done = true;
+ }
+}
+
static int axp288_handle_chrg_det_event(struct axp288_extcon_info *info)
{
int ret, stat, cfg, pwr_stat;
@@ -201,6 +223,8 @@ static int axp288_handle_chrg_det_event(struct axp288_extcon_info *info)
info->previous_cable = cable;
}

+ axp288_chrg_detect_complete(info);
+
return 0;

dev_det_ret:
@@ -222,8 +246,11 @@ static irqreturn_t axp288_extcon_isr(int irq, void *data)
return IRQ_HANDLED;
}

-static void axp288_extcon_enable(struct axp288_extcon_info *info)
+static void axp288_extcon_det_work(struct work_struct *work)
{
+ struct axp288_extcon_info *info =
+ container_of(work, struct axp288_extcon_info, det_work.work);
+
regmap_update_bits(info->regmap, AXP288_BC_GLOBAL_REG,
BC_GLOBAL_RUN, 0);
/* Enable the charger detection logic */
@@ -245,6 +272,7 @@ static int axp288_extcon_probe(struct platform_device *pdev)
info->regmap = axp20x->regmap;
info->regmap_irqc = axp20x->regmap_irqc;
info->previous_cable = EXTCON_NONE;
+ INIT_DELAYED_WORK(&info->det_work, axp288_extcon_det_work);

platform_set_drvdata(pdev, info);

@@ -287,7 +315,7 @@ static int axp288_extcon_probe(struct platform_device *pdev)
}

/* Start charger cable type detection */
- axp288_extcon_enable(info);
+ queue_delayed_work(system_wq, &info->det_work, 0);

return 0;
}
--
2.14.3
\
 
 \ /
  Last update: 2017-12-22 13:37    [W:0.265 / U:0.108 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site