lkml.org 
[lkml]   [2016]   [May]   [21]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2 1/2] ip6_gre: Fix MTU setting for ip6gretap
Date
When creat an ip6gretap interface with an unreachable route,
the MTU is about 14 bytes larger than what was needed.

If the remote address is reachable:
ping6 2001:0:130::1 -c 2
PING 2001:0:130::1(2001:0:130::1) 56 data bytes
64 bytes from 2001:0:130::1: icmp_seq=1 ttl=64 time=1.46 ms
64 bytes from 2001:0:130::1: icmp_seq=2 ttl=64 time=81.1 ms

--- 2001:0:130::1 ping statistics ---
2 packets transmitted, 2 received, 0% packet loss, time 1001ms
rtt min/avg/max/mdev = 1.465/41.316/81.167/39.851 ms

ip link add ip6gretap1 type ip6gretap\
local 2001:0:130::2 remote 2001:0:130::1
ip link show ip6gretap1
11: ip6gretap1@NONE: <BROADCAST,MULTICAST> mtu 1434 ...
link/ether c2:f3:f8:c1:2c:bf brd ff:ff:ff:ff:ff:ff

The MTU value 1434 is right. But if we delete the direct route:
ip -6 route del 2001:0:130::/64
ping6 2001:0:130::1 -c 2
connect: Network is unreachable
ip link add ip6gretap1 type ip6gretap\
local 2001:0:130::2 remote 2001:0:130::1
ip link show ip6gretap1
12: ip6gretap1@NONE: <BROADCAST,MULTICAST> mtu 1448 ...
link/ether 7e:e1:d2:c4:06:5e brd ff:ff:ff:ff:ff:ff

Now, the MTU value 1448 is larger than what was needed.

The reason is that if there is a reachable route, when
run following code in ip6gre_tnl_link_config:

if (p->flags & IP6_TNL_F_CAP_XMIT) {
int strict = (ipv6_addr_type(&p->raddr) &
(IPV6_ADDR_MULTICAST|IPV6_ADDR_LINKLOCAL));

struct rt6_info *rt = rt6_lookup(t->net,
&p->raddr, &p->laddr,
p->link, strict);

if (!rt)
return;

if (rt->dst.dev) {
dev->hard_header_len = rt->dst.dev->hard_header_len +
t_hlen;

if (set_mtu) {
dev->mtu = rt->dst.dev->mtu - t_hlen;
if (!(t->parms.flags & IP6_TNL_F_IGN_ENCAP_LIMIT))
dev->mtu -= 8;
if (dev->type == ARPHRD_ETHER)
dev->mtu -= ETH_HLEN;

if (dev->mtu < IPV6_MIN_MTU)
dev->mtu = IPV6_MIN_MTU;
}
}
ip6_rt_put(rt);
}

Because rt is not NULL here, so dev->mtu will subtract the ethernet
header length later. But when rt is NULL, it just simply return, so
dev->mtu doesn't update correctly in this situation.

This patch first verify the dev->type is ARPHRD_ETHER for ip6gretap
interface, and then decrease the mtu as early as possible.

Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
---
Changes in v2:
- Make the commit message more clearer.
---
net/ipv6/ip6_gre.c | 2 ++
1 file changed, 2 insertions(+)

diff --git a/net/ipv6/ip6_gre.c b/net/ipv6/ip6_gre.c
index 4541fa5..8ea5a4d 100644
--- a/net/ipv6/ip6_gre.c
+++ b/net/ipv6/ip6_gre.c
@@ -1029,6 +1029,8 @@ static int ip6gre_tunnel_init_common(struct net_device *dev)

dev->hard_header_len = LL_MAX_HEADER + t_hlen;
dev->mtu = ETH_DATA_LEN - t_hlen;
+ if (dev->type == ARPHRD_ETHER)
+ dev->mtu -= ETH_HLEN;
if (!(tunnel->parms.flags & IP6_TNL_F_IGN_ENCAP_LIMIT))
dev->mtu -= 8;

--
1.8.3.1


\
 
 \ /
  Last update: 2016-05-21 12:41    [W:0.337 / U:0.008 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site