lkml.org 
[lkml]   [2016]   [May]   [12]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2 1/2] dt: binding: Add Qualcomm WCNSS control binding
Date
This binding describes the control interface for the Qualcomm WCNSS.

Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
---

Changes since v1:
- Introduce reference to wcnss block node for register block definition
- Use wcnss block node compatible for hw version detection (riva vs pronto)
- Clean up compatible name for bt node

.../devicetree/bindings/soc/qcom/qcom,wcnss.txt | 115 +++++++++++++++++++++
1 file changed, 115 insertions(+)
create mode 100644 Documentation/devicetree/bindings/soc/qcom/qcom,wcnss.txt

diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,wcnss.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,wcnss.txt
new file mode 100644
index 000000000000..5413098a1e1a
--- /dev/null
+++ b/Documentation/devicetree/bindings/soc/qcom/qcom,wcnss.txt
@@ -0,0 +1,115 @@
+Qualcomm WCNSS Binding
+
+This binding describes the Qualcomm WCNSS hardware. It consists of control
+block and a BT, WiFi and FM radio block, all useing SMD as command channels.
+
+- compatible:
+ Usage: required
+ Value type: <string>
+ Definition: must be: "qcom,wcnss",
+
+- qcom,smd-channel:
+ Usage: required
+ Value type: <string>
+ Definition: standard SMD property specifying the SMD channel used for
+ communication with the WiFi firmware
+
+- qcom,mmio:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: reference to a node specifying the wcnss "ccu" and "dxe"
+ register blocks. The node must be compatible with one of
+ the following:
+ "qcom,riva",
+ "qcom,pronto"
+
+= SUBNODES
+The subnodes of the wcnss node are optional and describe the individual blocks in
+the WCNSS.
+
+== Bluetooth
+The following properties are defined to the bluetooth node:
+
+- compatible:
+ Usage: required
+ Value type: <string>
+ Definition: must be:
+ "qcom,wcnss-bt"
+
+== WiFi
+The following properties are defined to the WiFi node:
+
+- compatible:
+ Usage: required
+ Value type: <string>
+ Definition: must be one of:
+ "qcom,wcnss-wlan",
+
+- interrupts:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: should specify the "rx" and "tx" interrupts
+
+- interrupt-names:
+ Usage: required
+ Value type: <stringlist>
+ Definition: must contain "rx" and "tx"
+
+- qcom,state:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: should reference the tx-enable and tx-rings-empty SMEM states
+
+- qcom,state-names:
+ Usage: required
+ Value type: <stringlist>
+ Definition: must contain "tx-enable" and "tx-rings-empty"
+
+= EXAMPLE
+The following example represents a SMD node, with one edge representing the
+"pronto" subsystem, with the wcnss device and its wcn3680 BT and WiFi blocks
+described; as found on the 8974 platform.
+
+smd {
+ compatible = "qcom,smd";
+
+ pronto {
+ interrupts = <0 142 1>;
+
+ qcom,ipc = <&apcs 8 17>;
+ qcom,smd-edge = <6>;
+
+ wcnss {
+ compatible = "qcom,wcnss";
+ qcom,smd-channels = "WCNSS_CTRL";
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ qcom,wcnss = <&pronto>;
+
+ bt {
+ compatible = "qcom,wcnss-bt";
+ };
+
+ wlan {
+ compatible = "qcom,wcnss-wlan";
+
+ interrupts = <0 145 0>, <0 146 0>;
+ interrupt-names = "tx", "rx";
+
+ qcom,state = <&apps_smsm 10>, <&apps_smsm 9>;
+ qcom,state-names = "tx-enable", "tx-rings-empty";
+ };
+ };
+ };
+};
+
+soc {
+ pronto: pronto {
+ compatible = "qcom,pronto";
+
+ reg = <0xfb204000 0x2000>, <0xfb202000 0x1000>, <0xfb21b000 0x3000>;
+ reg-names = "ccu", "dxe", "pmu";
+ };
+};
--
2.5.0
\
 
 \ /
  Last update: 2016-05-13 01:41    [W:0.059 / U:0.016 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site