lkml.org 
[lkml]   [2015]   [Nov]   [1]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v1 02/20] clocksource: Add NPS400 timers driver
From
Date
On 10/31/2015 02:15 PM, Noam Camus wrote:
> From: Noam Camus <noamc@ezchip.com>
>
> Add internal tick generator which is shared by all cores.
> Each cluster of cores view it through dedicated address.
> This is used for SMP system where all CPUs synced by same
> clock source.
>
> Signed-off-by: Noam Camus <noamc@ezchip.com>
> Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
> Cc: Rob Herring <robh+dt@kernel.org>

Hi Noam,

Added Thomas Gleixner and John Stultz.

> ---
> .../bindings/timer/ezchip,nps400-timer.txt | 11 ++
> drivers/clocksource/Makefile | 1 +
> drivers/clocksource/timer-nps.c | 103 ++++++++++++++++++++
> 3 files changed, 115 insertions(+), 0 deletions(-)
> create mode 100644 Documentation/devicetree/bindings/timer/ezchip,nps400-timer.txt
> create mode 100644 drivers/clocksource/timer-nps.c
>
> diff --git a/Documentation/devicetree/bindings/timer/ezchip,nps400-timer.txt b/Documentation/devicetree/bindings/timer/ezchip,nps400-timer.txt
> new file mode 100644
> index 0000000..c5102c2
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/timer/ezchip,nps400-timer.txt
> @@ -0,0 +1,11 @@
> +NPS Network Processor
> +
> +Required properties:
> +
> +- compatible : should be "ezchip,nps400-timer"
> +
> +Example:
> +
> +timer {
> + compatible = "ezchip,nps400-timer";
> +};
> diff --git a/drivers/clocksource/Makefile b/drivers/clocksource/Makefile
> index 5c00863..28c17dc 100644
> --- a/drivers/clocksource/Makefile
> +++ b/drivers/clocksource/Makefile
> @@ -45,6 +45,7 @@ obj-$(CONFIG_VF_PIT_TIMER) += vf_pit_timer.o
> obj-$(CONFIG_CLKSRC_QCOM) += qcom-timer.o
> obj-$(CONFIG_MTK_TIMER) += mtk_timer.o
> obj-$(CONFIG_CLKSRC_PISTACHIO) += time-pistachio.o
> +obj-$(CONFIG_ARC_PLAT_EZNPS) += timer-nps.o

Please add an entry in the clocksource's Kconfig.

eg:

config NPS400_TIMER
bool "NPS400 clocksource driver" if COMPILE_TEST
help
NPS400 clocksource support.

and in the platform's Kconfig:

select NPS400_TIMER


> obj-$(CONFIG_ARM_ARCH_TIMER) += arm_arch_timer.o
> obj-$(CONFIG_ARM_GLOBAL_TIMER) += arm_global_timer.o
> diff --git a/drivers/clocksource/timer-nps.c b/drivers/clocksource/timer-nps.c
> new file mode 100644
> index 0000000..83a0a9d
> --- /dev/null
> +++ b/drivers/clocksource/timer-nps.c
> @@ -0,0 +1,103 @@
> +/*
> + * Copyright(c) 2015 EZchip Technologies.
> + *
> + * This program is free software; you can redistribute it and/or modify it
> + * under the terms and conditions of the GNU General Public License,
> + * version 2, as published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope it will be useful, but WITHOUT
> + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
> + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
> + * more details.
> + *
> + * The full GNU General Public License is included in this distribution in
> + * the file called "COPYING".
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/clockchips.h>
> +#include <linux/delay.h>
> +#include <linux/interrupt.h>
> +#include <linux/irq.h>
> +#include <linux/irqreturn.h>
> +#include <linux/reset.h>
> +#include <linux/slab.h>
> +#include <linux/of.h>
> +#include <linux/of_address.h>
> +#include <linux/of_irq.h>
> +#include <linux/of_fdt.h>
> +#include <plat/ctop.h>

Are you sure all the headers are needed ?

> +#define NPS_MSU_TICK_LOW 0xC8
> +#define NPS_CLUSTER_OFFSET 8
> +#define NPS_CLUSTER_NUM 16
> +
> +static u32 nps_msu_reg_low_addr[NPS_CLUSTER_NUM] __read_mostly;
> +
> +/*
> + * To get the value from the Global Timer Counter register proceed as follows:
> + * 1. Read the upper 32-bit timer counter register
> + * 2. Read the lower 32-bit timer counter register
> + * 3. Read the upper 32-bit timer counter register again. If the value is
> + * different to the 32-bit upper value read previously, go back to step 2.
> + * Otherwise the 64-bit timer counter value is correct.
> + */
> +static cycle_t nps_clksrc_read(struct clocksource *clksrc)
> +{
> + u64 counter;
> + u32 lower;
> + u32 upper, old_upper;
> + int cpu;
> + int cluster;
> + void *lower_p, *upper_p;
> + unsigned long flags;
> +
> + local_irq_save(flags);

Why do you need to disable the interrupt here ?

> + cpu = smp_processor_id();
> + cluster = cpu >> NPS_CLUSTER_OFFSET;
> + lower_p = (void *)nps_msu_reg_low_addr[cluster];
> + upper_p = lower_p + 4;
> + local_irq_restore(flags);
> +
> + upper = ioread32be(upper_p);
> + do {
> + old_upper = upper;
> + lower = ioread32be(lower_p);
> + upper = ioread32be(upper_p);
> + } while (upper != old_upper);
> +
> + counter = upper;
> + counter <<= 32;
> + counter |= lower;
> + return (cycle_t)counter;

May be you can consider using only the 32bits. Sometimes it is faster
than using 64bits arithmetic and reading the register three times.

https://lkml.org/lkml/2014/6/20/431

> +}
> +
> +static struct clocksource nps_counter = {
> + .name = "EZnps-tick",
> + .rating = 301,
> + .read = nps_clksrc_read,
> + .mask = CLOCKSOURCE_MASK(64),
> + .flags = CLOCK_SOURCE_IS_CONTINUOUS,
> +};
> +
> +static void __init nps_setup_clocksource(struct device_node *node)
> +{
> + struct clocksource *clksrc = &nps_counter;
> + unsigned long rate, dt_root;
> + int ret, cluster;
> +
> + for (cluster = 0; cluster < NPS_CLUSTER_NUM; cluster++)
> + nps_msu_reg_low_addr[cluster] =
> + nps_host_reg((cluster << NPS_CLUSTER_OFFSET),
> + NPS_MSU_BLKID, NPS_MSU_TICK_LOW);
> +
> + dt_root = of_get_flat_dt_root();
> + rate = (u32)of_get_flat_dt_prop(dt_root, "clock-frequency", NULL);

Why are you using 'of_get_flat_dt_root' / 'of_get_flat_dt_prop' ?

> + ret = clocksource_register_hz(clksrc, rate);
> + if (ret)
> + pr_err("Couldn't register clock source.\n");
> +}
> +
> +CLOCKSOURCE_OF_DECLARE(nps_400, "nps,400-timer",
> + nps_setup_clocksource);
>


--
<http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs

Follow Linaro: <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog



\
 
 \ /
  Last update: 2015-11-01 22:01    [W:2.604 / U:1.168 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site