lkml.org 
[lkml]   [2014]   [Jul]   [22]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 26/28] phy: miphy365x: Add Device Tree bindings for the MiPHY365x
Date
From: Lee Jones <lee.jones@linaro.org>

The MiPHY365x is a Generic PHY which can serve various SATA or PCIe
devices. It has 2 ports which it can use for either; both SATA, both
PCIe or one of each in any configuration.

Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
---
.../devicetree/bindings/phy/phy-miphy365x.txt | 76 ++++++++++++++++++++
1 file changed, 76 insertions(+)
create mode 100644 Documentation/devicetree/bindings/phy/phy-miphy365x.txt

diff --git a/Documentation/devicetree/bindings/phy/phy-miphy365x.txt b/Documentation/devicetree/bindings/phy/phy-miphy365x.txt
new file mode 100644
index 0000000..42c8808
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/phy-miphy365x.txt
@@ -0,0 +1,76 @@
+STMicroelectronics STi MIPHY365x PHY binding
+============================================
+
+This binding describes a miphy device that is used to control PHY hardware
+for SATA and PCIe.
+
+Required properties (controller (parent) node):
+- compatible : Should be "st,miphy365x-phy"
+- st,syscfg : Should be a phandle of the system configuration register group
+ which contain the SATA, PCIe mode setting bits
+
+Required nodes : A sub-node is required for each channel the controller
+ provides. Address range information including the usual
+ 'reg' and 'reg-names' properties are used inside these
+ nodes to describe the controller's topology. These nodes
+ are translated by the driver's .xlate() function.
+
+Required properties (port (child) node):
+- #phy-cells : Should be 1 (See second example)
+ Cell after port phandle is device type from:
+ - MIPHY_TYPE_SATA
+ - MIPHY_TYPE_PCI
+- reg : Address and length of register sets for each device in
+ "reg-names"
+- reg-names : The names of the register addresses corresponding to the
+ registers filled in "reg":
+ - sata: For SATA devices
+ - pcie: For PCIe devices
+ - syscfg: To specify the syscfg based config register
+
+Optional properties (port (child) node):
+- st,sata-gen : Generation of locally attached SATA IP. Expected values
+ are {1,2,3). If not supplied generation 1 hardware will
+ be expected
+- st,pcie-tx-pol-inv : Bool property to invert the polarity PCIe Tx (Txn/Txp)
+- st,sata-tx-pol-inv : Bool property to invert the polarity SATA Tx (Txn/Txp)
+
+Example:
+
+ miphy365x_phy: miphy365x@fe382000 {
+ compatible = "st,miphy365x-phy";
+ st,syscfg = <&syscfg_rear>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ phy_port0: port@fe382000 {
+ reg = <0xfe382000 0x100>, <0xfe394000 0x100>, <0x824 0x4>;
+ reg-names = "sata", "pcie", "syscfg";
+ #phy-cells = <1>;
+ st,sata-gen = <3>;
+ };
+
+ phy_port1: port@fe38a000 {
+ reg = <0xfe38a000 0x100>, <0xfe804000 0x100>, <0x828 0x4>;;
+ reg-names = "sata", "pcie", "syscfg";
+ #phy-cells = <1>;
+ st,pcie-tx-pol-inv;
+ };
+ };
+
+Specifying phy control of devices
+=================================
+
+Device nodes should specify the configuration required in their "phys"
+property, containing a phandle to the phy port node and a device type.
+
+Example:
+
+#include <dt-bindings/phy/phy-miphy365x.h>
+
+ sata0: sata@fe380000 {
+ ...
+ phys = <&phy_port0 MIPHY_TYPE_SATA>;
+ ...
+ };
--
1.7.9.5


\
 
 \ /
  Last update: 2014-07-26 06:01    [W:0.233 / U:0.092 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site