lkml.org 
[lkml]   [2014]   [Oct]   [27]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
SubjectRe: [PATCH v3] rtc: omap: add support for pmic_power_en
On Mon, 27 Oct 2014 09:09:28 +0100 Johan Hovold <johan@kernel.org> wrote:

> Add new property "ti,system-power-controller" to register the RTC as a
> power-off handler.
>
> Some RTC IP revisions can control an external PMIC via the pmic_power_en
> pin, which can be configured to transition to OFF on ALARM2 events and
> back to ON on subsequent ALARM (wakealarm) events.
>
> This is based on earlier work by Colin Foe-Parker and AnilKumar Ch. [1]
>
> [1] https://www.mail-archive.com/linux-omap@vger.kernel.org/msg82127.html
>
> Tested-by: Felipe Balbi <balbi@ti.com>
> Signed-off-by: Johan Hovold <johan@kernel.org>
> ---
>
> Changes since v2:
> - add two-second delay to allow alarm to trigger before returning

hmpf. As this sentence is below the ^--- it doesn't get into the
changelog.

> ...
>
> +static void omap_rtc_power_off(void)
> +{
> + struct omap_rtc *rtc = omap_rtc_power_off_rtc;
> + struct rtc_time tm;
> + unsigned long now;
> + u32 val;
> +
> + /* enable pmic_power_en control */
> + val = rtc_readl(rtc, OMAP_RTC_PMIC_REG);
> + rtc_writel(rtc, OMAP_RTC_PMIC_REG, val | OMAP_RTC_PMIC_POWER_EN_EN);
> +
> + /* set alarm two seconds from now */
> + omap_rtc_read_time_raw(rtc, &tm);
> + bcd2tm(&tm);
> + rtc_tm_to_time(&tm, &now);
> + rtc_time_to_tm(now + 2, &tm);
> +
> + if (tm2bcd(&tm) < 0) {
> + dev_err(&rtc->rtc->dev, "power off failed\n");
> + return;
> + }
> +
> + rtc_wait_not_busy(rtc);
> +
> + rtc_write(rtc, OMAP_RTC_ALARM2_SECONDS_REG, tm.tm_sec);
> + rtc_write(rtc, OMAP_RTC_ALARM2_MINUTES_REG, tm.tm_min);
> + rtc_write(rtc, OMAP_RTC_ALARM2_HOURS_REG, tm.tm_hour);
> + rtc_write(rtc, OMAP_RTC_ALARM2_DAYS_REG, tm.tm_mday);
> + rtc_write(rtc, OMAP_RTC_ALARM2_MONTHS_REG, tm.tm_mon);
> + rtc_write(rtc, OMAP_RTC_ALARM2_YEARS_REG, tm.tm_year);
> +
> + /*
> + * enable ALARM2 interrupt
> + *
> + * NOTE: this fails on AM3352 if rtc_write (writeb) is used
> + */
> + val = rtc_read(rtc, OMAP_RTC_INTERRUPTS_REG);
> + rtc_writel(rtc, OMAP_RTC_INTERRUPTS_REG,
> + val | OMAP_RTC_INTERRUPTS_IT_ALARM2);
> +
> + mdelay(2000);

And it is uncommented.

How on earth is a reader to know why this is here?

I can do this

--- a/drivers/rtc/rtc-omap.c~rtc-omap-add-support-for-pmic_power_en-v3-fix
+++ a/drivers/rtc/rtc-omap.c
@@ -417,6 +417,7 @@ static void omap_rtc_power_off(void)
rtc_writel(rtc, OMAP_RTC_INTERRUPTS_REG,
val | OMAP_RTC_INTERRUPTS_IT_ALARM2);

+ /* Allow alarm to trigger before returning */
mdelay(2000);
}


But it doesn't explain *why* we want the alarm to trigger before
returning.



\
 
 \ /
  Last update: 2014-10-28 00:21    [W:0.206 / U:0.788 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site