lkml.org 
[lkml]   [2011]   [Nov]   [25]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 1/2] gpiolib: introduce gpio_set_pullup
On 16:16 Fri 25 Nov     , Felipe Balbi wrote:
> Hi,
>
> On Fri, Nov 25, 2011 at 03:08:39PM +0100, Jean-Christophe PLAGNIOL-VILLARD wrote:
> > Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
> > Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
> > Cc: Grant Likely <grant.likely@secretlab.ca>
> > ---
> > drivers/gpio/gpiolib.c | 44 ++++++++++++++++++++++++++++++++++++++++++++
> > include/asm-generic/gpio.h | 4 ++++
> > include/linux/gpio.h | 5 +++++
> > 3 files changed, 53 insertions(+), 0 deletions(-)
> >
> > diff --git a/drivers/gpio/gpiolib.c b/drivers/gpio/gpiolib.c
> > index a971e3d..b7e5e75 100644
> > --- a/drivers/gpio/gpiolib.c
> > +++ b/drivers/gpio/gpiolib.c
> > @@ -1519,6 +1519,50 @@ fail:
> > }
> > EXPORT_SYMBOL_GPL(gpio_set_debounce);
> >
> > +/**
> > + * gpio_set_pullup - sets @pullup for a @gpio
> > + * @gpio: the gpio to set pullup
> > + * @pullup: pullup level
> > + */
> > +int gpio_set_pullup(unsigned gpio, unsigned pullup)
> > +{
> > + unsigned long flags;
> > + struct gpio_chip *chip;
> > + struct gpio_desc *desc = &gpio_desc[gpio];
> > + int status = -EINVAL;
> > +
> > + spin_lock_irqsave(&gpio_lock, flags);
> > +
> > + if (!gpio_is_valid(gpio))
> > + goto fail;
> > + chip = desc->chip;
> > + if (!chip || !chip->set_pullup)
> > + goto fail;
> > + gpio -= chip->base;
> > + if (gpio >= chip->ngpio)
> > + goto fail;
> > + status = gpio_ensure_requested(desc, gpio);
> > + if (status < 0)
> > + goto fail;
> > +
> > + /* now we know the gpio is valid and chip won't vanish */
> > +
> > + spin_unlock_irqrestore(&gpio_lock, flags);
> > +
> > + might_sleep_if(chip->can_sleep);
> > +
> > + return chip->set_pullup(chip, gpio, pullup);
> > +
> > +fail:
> > + spin_unlock_irqrestore(&gpio_lock, flags);
> > + if (status)
> > + pr_debug("%s: gpio-%d status %d\n",
> > + __func__, gpio, status);
> > +
> > + return status;
> > +}
> > +EXPORT_SYMBOL_GPL(gpio_set_pullup);
>
> Maybe I'm missing something, but isn't it essentially what
> gpio_set_value() does ? I mean, you set a pullup and you get '1' value
> and set a pulldown and you get a '0' value ??
>
> Without a proper description of the necessity for this change, I can't
> easily tell them apart :-(
set_value is for output set_pullup is for input mode

some IP allow you when you configure an gpio as input to enable the internal pullup
so no need on the board to add an external pull up

Best Regards,
J.

>
> --
> balbi




\
 
 \ /
  Last update: 2011-11-25 15:37    [W:1.312 / U:0.544 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site