lkml.org 
[lkml]   [2010]   [Feb]   [14]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
Subject2.6.33-rc8 regression: irq11: nobody cared, during yenta registration
Just tried 2.6.33-rcx8 on my laptop (Thinkpad X20 in a dock) that was 
last running 2.6.33-rc5 without problems. Gor irq11: nobody carec like
below. Seems to be repeatabale. lspci also below.

Linux version 2.6.33-rc8 (mroos@tulp) (gcc version 4.4.3 (Debian 4.4.3-2) ) #1 Sun Feb 14 10:37:28 EET 2010
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000dd000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000013ff0000 (usable)
BIOS-e820: 0000000013ff0000 - 0000000013ffec00 (ACPI data)
BIOS-e820: 0000000013ffec00 - 0000000014000000 (ACPI NVS)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
Notice: NX (Execute Disable) protection missing in CPU or disabled in BIOS!
DMI 2.3 present.
last_pfn = 0x13ff0 max_arch_pfn = 0x100000
MTRR default type: uncachable
MTRR fixed ranges enabled:
00000-9FFFF write-back
A0000-BFFFF uncachable
C0000-CFFFF write-protect
D0000-DFFFF uncachable
E0000-FFFFF write-protect
MTRR variable ranges enabled:
0 base 000000000 mask FF0000000 write-back
1 base 010000000 mask FFC000000 write-back
2 disabled
3 disabled
4 disabled
5 disabled
6 disabled
7 disabled
PAT not supported by CPU.
initial memory mapped : 0 - 01800000
init_memory_mapping: 0000000000000000-0000000013ff0000
0000000000 - 0000400000 page 4k
0000400000 - 0013c00000 page 2M
0013c00000 - 0013ff0000 page 4k
kernel direct mapping tables up to 13ff0000 @ 7000-c000
RAMDISK: 0ec57000 - 0f033f82
ACPI: RSDP 000f6ec0 00014 (v00 PTLTD )
ACPI: RSDT 13ff5c49 0002C (v01 PTLTD RSDT 06040000 LTP 00000000)
ACPI: FACP 13ffeb65 00074 (v01 IBM TP-X21 06040000 00000000)
ACPI: DSDT 13ff5c75 08EF0 (v01 IBM TP-X21 06040000 MSFT 0100000C)
ACPI: FACS 13fff000 00040
ACPI: BOOT 13ffebd9 00027 (v01 PTLTD $SBFTBL$ 06040000 LTP 00000001)
319MB LOWMEM available.
mapped low ram: 0 - 13ff0000
low ram: 0 - 13ff0000
node 0 low ram: 00000000 - 13ff0000
node 0 bootmap 00008000 - 0000a800
(8 early reservations) ==> bootmem [0000000000 - 0013ff0000]
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
#1 [0001000000 - 00013bf0c0] TEXT DATA BSS ==> [0001000000 - 00013bf0c0]
#2 [000ec57000 - 000f033f82] RAMDISK ==> [000ec57000 - 000f033f82]
#3 [000009f800 - 0000100000] BIOS reserved ==> [000009f800 - 0000100000]
#4 [00013c0000 - 00013c60d9] BRK ==> [00013c0000 - 00013c60d9]
#5 [0000001000 - 0000005000] ACPI WAKEUP ==> [0000001000 - 0000005000]
#6 [0000007000 - 0000008000] PGTABLE ==> [0000007000 - 0000008000]
#7 [0000008000 - 000000b000] BOOTMAP ==> [0000008000 - 000000b000]
Zone PFN ranges:
DMA 0x00000000 -> 0x00001000
Normal 0x00001000 -> 0x00013ff0
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0x00000000 -> 0x0000009f
0: 0x00000100 -> 0x00013ff0
On node 0 totalpages: 81807
free_area_init_node: node 0, pgdat c1335e60, node_mem_map c13c7000
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 3967 pages, LIFO batch:0
Normal zone: 608 pages used for memmap
Normal zone: 77200 pages, LIFO batch:15
ACPI: PM-Timer IO Port: 0x1008
PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000dd000
PM: Registered nosave memory: 00000000000dd000 - 0000000000100000
Allocating PCI resources starting at 14000000 (gap: 14000000:ebf80000)
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 81167
Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.33-rc8 root=UUID=5a228fa1-6850-44bc-9b37-73af4d751e16 ro resume=/dev/sda2
PID hash table entries: 2048 (order: 1, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
Memory: 316132k/327616k available (2384k kernel code, 10804k reserved, 918k data, 272k init, 0k highmem)
virtual kernel memory layout:
fixmap : 0xfffe5000 - 0xfffff000 ( 104 kB)
vmalloc : 0xd47f0000 - 0xfffe3000 ( 695 MB)
lowmem : 0xc0000000 - 0xd3ff0000 ( 319 MB)
.init : 0xc133a000 - 0xc137e000 ( 272 kB)
.data : 0xc12540eb - 0xc1339a04 ( 918 kB)
.text : 0xc1000000 - 0xc12540eb (2384 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
NR_IRQS:16
CPU 0 irqstacks, hard=c130e000 soft=c130f000
Console: colour VGA+ 80x25
console [tty0] enabled
Fast TSC calibration using PIT
Detected 597.475 MHz processor.
Calibrating delay loop (skipped), value calculated using timer frequency.. 1194.95 BogoMIPS (lpj=5974750)
Security Framework initialized
Mount-cache hash table entries: 512
Performance Events:
no APIC, boot with the "lapic" boot parameter to force-enable it.
no hardware sampling interrupt available.
p6 PMU driver.
... version: 0
... bit width: 32
... generic registers: 2
... value mask: 00000000ffffffff
... max period: 000000007fffffff
... fixed-purpose events: 0
... event mask: 0000000000000003
CPU: Intel Pentium III (Coppermine) stepping 03
Checking 'hlt' instruction... OK.
ACPI: Core revision 20091214
ACPI: setting ELCR to 0200 (from 0e20)
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfd94f, last bus=14
PCI: Using configuration type 1 for base access
bio: create slab <bio-0> at 0
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using PIC for interrupt routing
ACPI: EC: GPE = 0x9, I/O: command/status = 0x66, data = 0x62
ACPI: Power Resource [PSIO] (on)
ACPI: Power Resource [PSER] (off)
ACPI: ACPI Dock Station Driver: 2 docks/bays found
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci_root PNP0A03:00: ignoring host bridge windows from ACPI; boot with "pci=use_crs" to use them
pci_root PNP0A03:00: host bridge window [io 0x0000-0x0cf7] (ignored)
pci_root PNP0A03:00: host bridge window [io 0x0d00-0xffff] (ignored)
pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff] (ignored)
pci_root PNP0A03:00: host bridge window [mem 0x000d0000-0x000d3fff] (ignored)
pci_root PNP0A03:00: host bridge window [mem 0x000d4000-0x000d7fff] (ignored)
pci_root PNP0A03:00: host bridge window [mem 0x14000000-0xffdfffff] (ignored)
pci 0000:00:00.0: reg 10: [mem 0xf8000000-0xfbffffff pref]
pci 0000:00:04.0: supports D1 D2
pci 0000:00:07.1: reg 20: [io 0x1800-0x180f]
pci 0000:00:07.2: reg 20: [io 0x1820-0x183f]
pci 0000:00:07.3: quirk: [io 0x1000-0x103f] claimed by PIIX4 ACPI
pci 0000:00:07.3: quirk: [io 0x1040-0x104f] claimed by PIIX4 SMB
pci 0000:00:07.3: PIIX4 devres I PIO at 03f0-03f7
pci 0000:00:07.3: PIIX4 devres J PIO at 002e-002f
pci 0000:00:08.0: reg 10: [mem 0x50000000-0x50000fff]
pci 0000:00:08.0: supports D1 D2
pci 0000:00:08.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:08.0: PME# disabled
pci 0000:00:08.1: reg 10: [mem 0x50100000-0x50100fff]
pci 0000:00:08.1: supports D1 D2
pci 0000:00:08.1: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:08.1: PME# disabled
pci 0000:00:0a.0: reg 10: [mem 0xf4010000-0xf4010fff]
pci 0000:00:0a.0: reg 14: [io 0x1840-0x187f]
pci 0000:00:0a.0: reg 18: [mem 0xf4020000-0xf403ffff]
pci 0000:00:0a.0: reg 30: [mem 0x00000000-0x000fffff pref]
pci 0000:00:0a.0: supports D1 D2
pci 0000:00:0a.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:0a.0: PME# disabled
pci 0000:00:0a.1: reg 10: [io 0x1810-0x1817]
pci 0000:00:0a.1: reg 14: [mem 0xf4011000-0xf4011fff]
pci 0000:00:0a.1: supports D1 D2
pci 0000:00:0a.1: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:0a.1: PME# disabled
pci 0000:00:0b.0: reg 10: [mem 0xf4012000-0xf4012fff]
pci 0000:00:0b.0: reg 14: [mem 0xf4000000-0xf400ffff]
pci 0000:00:0b.0: supports D1 D2
pci 0000:00:0b.0: PME# supported from D0 D1 D2 D3hot
pci 0000:00:0b.0: PME# disabled
pci 0000:01:00.0: reg 10: [mem 0xf5000000-0xf5ffffff]
pci 0000:01:00.0: reg 14: [io 0x2000-0x20ff]
pci 0000:01:00.0: reg 18: [mem 0xf4100000-0xf4100fff]
pci 0000:01:00.0: reg 30: [mem 0x00000000-0x0001ffff pref]
pci 0000:01:00.0: supports D1 D2
pci 0000:00:01.0: PCI bridge to [bus 01-01]
pci 0000:00:01.0: bridge window [io 0x2000-0x2fff]
pci 0000:00:01.0: bridge window [mem 0xf4100000-0xf5ffffff]
pci 0000:02:00.0: reg 10: [mem 0xf6000000-0xf60007ff]
pci 0000:02:00.0: reg 14: [io 0x3000-0x307f]
pci 0000:02:00.0: supports D2
pci 0000:02:00.0: PME# supported from D2 D3hot D3cold
pci 0000:02:00.0: PME# disabled
pci 0000:02:01.0: reg 10: [io 0x30a0-0x30a7]
pci 0000:02:01.0: reg 14: [io 0x3094-0x3097]
pci 0000:02:01.0: reg 18: [io 0x3098-0x309f]
pci 0000:02:01.0: reg 1c: [io 0x3090-0x3093]
pci 0000:02:01.0: reg 20: [io 0x3080-0x308f]
pci 0000:02:01.0: supports D1 D2
pci 0000:02:02.0: reg 10: [mem 0x52000000-0x52000fff]
pci 0000:02:02.0: supports D1 D2
pci 0000:02:02.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:02:02.0: PME# disabled
pci 0000:02:02.1: reg 10: [mem 0x53000000-0x53000fff]
pci 0000:02:02.1: supports D1 D2
pci 0000:02:02.1: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:02:02.1: PME# disabled
pci 0000:00:04.0: PCI bridge to [bus 02-08] (subtractive decode)
pci 0000:00:04.0: bridge window [io 0x0000-0x0fff]
pci 0000:00:04.0: bridge window [mem 0x00000000-0x000fffff]
pci 0000:00:04.0: bridge window [mem 0x00000000-0x000fffff pref]
pci_bus 0000:00: on NUMA node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.DOCK._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 9 *11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 9 11) *10
ACPI: PCI Interrupt Link [LNKC] (IRQs *9 11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 9 11) *5
vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
vgaarb: loaded
PCI: Using ACPI for IRQ routing
PCI: pci_cache_line_size set to 32 bytes
pci 0000:00:04.0: can't reserve window [io 0x0000-0x0fff]
pci 0000:00:04.0: can't reserve window [mem 0x00000000-0x000fffff]
pci 0000:00:04.0: can't reserve window [mem 0x00000000-0x000fffff pref]
Switching to clocksource tsc
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp 00:00: disabling [mem 0x00000000-0x0009ffff] because it overlaps 0000:00:0a.0 BAR 6 [mem 0x00000000-0x000fffff pref]
pnp 00:00: disabling [mem 0x000c0000-0x000c3fff] because it overlaps 0000:00:0a.0 BAR 6 [mem 0x00000000-0x000fffff pref]
pnp 00:00: disabling [mem 0x000c4000-0x000c7fff] because it overlaps 0000:00:0a.0 BAR 6 [mem 0x00000000-0x000fffff pref]
pnp 00:00: disabling [mem 0x000c8000-0x000cbfff] because it overlaps 0000:00:0a.0 BAR 6 [mem 0x00000000-0x000fffff pref]
pnp 00:00: disabling [mem 0x000cc000-0x000cffff] because it overlaps 0000:00:0a.0 BAR 6 [mem 0x00000000-0x000fffff pref]
pnp 00:00: disabling [mem 0x000d0000-0x000cffff disabled] because it overlaps 0000:00:0a.0 BAR 6 [mem 0x00000000-0x000fffff pref]
pnp 00:00: disabling [mem 0x000d4000-0x000d3fff disabled] because it overlaps 0000:00:0a.0 BAR 6 [mem 0x00000000-0x000fffff pref]
pnp 00:00: disabling [mem 0x000d8000-0x000dbfff] because it overlaps 0000:00:0a.0 BAR 6 [mem 0x00000000-0x000fffff pref]
pnp 00:00: disabling [mem 0x000dc000-0x000dffff] because it overlaps 0000:00:0a.0 BAR 6 [mem 0x00000000-0x000fffff pref]
pnp 00:00: disabling [mem 0x000e0000-0x000e3fff] because it overlaps 0000:00:0a.0 BAR 6 [mem 0x00000000-0x000fffff pref]
pnp 00:00: disabling [mem 0x000e4000-0x000e7fff] because it overlaps 0000:00:0a.0 BAR 6 [mem 0x00000000-0x000fffff pref]
pnp 00:00: disabling [mem 0x000e8000-0x000ebfff] because it overlaps 0000:00:0a.0 BAR 6 [mem 0x00000000-0x000fffff pref]
pnp 00:00: disabling [mem 0x000ec000-0x000effff] because it overlaps 0000:00:0a.0 BAR 6 [mem 0x00000000-0x000fffff pref]
pnp 00:00: disabling [mem 0x000f0000-0x000fffff] because it overlaps 0000:00:0a.0 BAR 6 [mem 0x00000000-0x000fffff pref]
pnp: PnP ACPI: found 13 devices
ACPI: ACPI bus type pnp unregistered
system 00:00: [mem 0x00100000-0x13ffffff] could not be reserved
system 00:00: [mem 0xfff80000-0xffffffff] has been reserved
system 00:02: [io 0x1000-0x103f] has been reserved
system 00:02: [io 0x1040-0x104f] has been reserved
system 00:02: [io 0xfe00-0xfe0f] has been reserved
pci 0000:00:04.0: BAR 8: assigned [mem 0x14000000-0x1bffffff]
pci 0000:00:04.0: BAR 9: assigned [mem 0x1c000000-0x23ffffff pref]
pci 0000:00:08.0: BAR 9: assigned [mem 0x24000000-0x27ffffff pref]
pci 0000:00:08.0: BAR 10: assigned [mem 0x28000000-0x2bffffff]
pci 0000:00:08.1: BAR 9: assigned [mem 0x2c000000-0x2fffffff pref]
pci 0000:00:08.1: BAR 10: assigned [mem 0x30000000-0x33ffffff]
pci 0000:00:01.0: BAR 9: assigned [mem 0x34000000-0x340fffff pref]
pci 0000:00:0a.0: BAR 6: assigned [mem 0x34100000-0x341fffff pref]
pci 0000:00:04.0: BAR 7: assigned [io 0x4000-0x4fff]
pci 0000:00:08.0: BAR 7: assigned [io 0x1400-0x14ff]
pci 0000:00:08.0: BAR 8: assigned [io 0x1c00-0x1cff]
pci 0000:00:08.1: BAR 7: assigned [io 0x3400-0x34ff]
pci 0000:00:08.1: BAR 8: assigned [io 0x3800-0x38ff]
pci 0000:01:00.0: BAR 6: assigned [mem 0x34000000-0x3401ffff pref]
pci 0000:00:01.0: PCI bridge to [bus 01-01]
pci 0000:00:01.0: bridge window [io 0x2000-0x2fff]
pci 0000:00:01.0: bridge window [mem 0xf4100000-0xf5ffffff]
pci 0000:00:01.0: bridge window [mem 0x34000000-0x340fffff pref]
pci 0000:02:02.0: BAR 9: assigned [mem 0x1c000000-0x1fffffff pref]
pci 0000:02:02.0: BAR 10: assigned [mem 0x14000000-0x17ffffff]
pci 0000:02:02.1: BAR 9: assigned [mem 0x20000000-0x23ffffff pref]
pci 0000:02:02.1: BAR 10: assigned [mem 0x18000000-0x1bffffff]
pci 0000:02:02.0: BAR 7: assigned [io 0x4000-0x40ff]
pci 0000:02:02.0: BAR 8: assigned [io 0x4400-0x44ff]
pci 0000:02:02.1: BAR 7: assigned [io 0x4800-0x48ff]
pci 0000:02:02.1: BAR 8: assigned [io 0x4c00-0x4cff]
pci 0000:02:02.0: CardBus bridge to [bus 03-06]
pci 0000:02:02.0: bridge window [io 0x4000-0x40ff]
pci 0000:02:02.0: bridge window [io 0x4400-0x44ff]
pci 0000:02:02.0: bridge window [mem 0x1c000000-0x1fffffff pref]
pci 0000:02:02.0: bridge window [mem 0x14000000-0x17ffffff]
pci 0000:02:02.1: CardBus bridge to [bus 07-07]
pci 0000:02:02.1: bridge window [io 0x4800-0x48ff]
pci 0000:02:02.1: bridge window [io 0x4c00-0x4cff]
pci 0000:02:02.1: bridge window [mem 0x20000000-0x23ffffff pref]
pci 0000:02:02.1: bridge window [mem 0x18000000-0x1bffffff]
pci 0000:00:04.0: PCI bridge to [bus 02-08]
pci 0000:00:04.0: bridge window [io 0x4000-0x4fff]
pci 0000:00:04.0: bridge window [mem 0x14000000-0x1bffffff]
pci 0000:00:04.0: bridge window [mem 0x1c000000-0x23ffffff pref]
pci 0000:00:08.0: CardBus bridge to [bus 09-0c]
pci 0000:00:08.0: bridge window [io 0x1400-0x14ff]
pci 0000:00:08.0: bridge window [io 0x1c00-0x1cff]
pci 0000:00:08.0: bridge window [mem 0x24000000-0x27ffffff pref]
pci 0000:00:08.0: bridge window [mem 0x28000000-0x2bffffff]
pci 0000:00:08.1: CardBus bridge to [bus 0d-10]
pci 0000:00:08.1: bridge window [io 0x3400-0x34ff]
pci 0000:00:08.1: bridge window [io 0x3800-0x38ff]
pci 0000:00:08.1: bridge window [mem 0x2c000000-0x2fffffff pref]
pci 0000:00:08.1: bridge window [mem 0x30000000-0x33ffffff]
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 9
PCI: setting IRQ 9 as level-triggered
pci 0000:02:02.0: PCI INT A -> Link[LNKC] -> GSI 9 (level, low) -> IRQ 9
pci 0000:02:02.1: PCI INT A -> Link[LNKC] -> GSI 9 (level, low) -> IRQ 9
pci 0000:00:08.0: power state changed by ACPI to D0
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
pci 0000:00:08.0: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
pci 0000:00:08.1: power state changed by ACPI to D0
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
pci 0000:00:08.1: PCI INT B -> Link[LNKB] -> GSI 11 (level, low) -> IRQ 11
pci_bus 0000:00: resource 0 [io 0x0000-0xffff]
pci_bus 0000:00: resource 1 [mem 0x00000000-0xffffffff]
pci_bus 0000:01: resource 0 [io 0x2000-0x2fff]
pci_bus 0000:01: resource 1 [mem 0xf4100000-0xf5ffffff]
pci_bus 0000:01: resource 2 [mem 0x34000000-0x340fffff pref]
pci_bus 0000:02: resource 0 [io 0x4000-0x4fff]
pci_bus 0000:02: resource 1 [mem 0x14000000-0x1bffffff]
pci_bus 0000:02: resource 2 [mem 0x1c000000-0x23ffffff pref]
pci_bus 0000:02: resource 3 [io 0x0000-0xffff]
pci_bus 0000:02: resource 4 [mem 0x00000000-0xffffffff]
pci_bus 0000:03: resource 0 [io 0x4000-0x40ff]
pci_bus 0000:03: resource 1 [io 0x4400-0x44ff]
pci_bus 0000:03: resource 2 [mem 0x1c000000-0x1fffffff pref]
pci_bus 0000:03: resource 3 [mem 0x14000000-0x17ffffff]
pci_bus 0000:07: resource 0 [io 0x4800-0x48ff]
pci_bus 0000:07: resource 1 [io 0x4c00-0x4cff]
pci_bus 0000:07: resource 2 [mem 0x20000000-0x23ffffff pref]
pci_bus 0000:07: resource 3 [mem 0x18000000-0x1bffffff]
pci_bus 0000:09: resource 0 [io 0x1400-0x14ff]
pci_bus 0000:09: resource 1 [io 0x1c00-0x1cff]
pci_bus 0000:09: resource 2 [mem 0x24000000-0x27ffffff pref]
pci_bus 0000:09: resource 3 [mem 0x28000000-0x2bffffff]
pci_bus 0000:0d: resource 0 [io 0x3400-0x34ff]
pci_bus 0000:0d: resource 1 [io 0x3800-0x38ff]
pci_bus 0000:0d: resource 2 [mem 0x2c000000-0x2fffffff pref]
pci_bus 0000:0d: resource 3 [mem 0x30000000-0x33ffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
pci 0000:00:00.0: Limiting direct PCI/PCI transfers
pci 0000:01:00.0: Boot video device
PCI: CLS 32 bytes, default 32
Unpacking initramfs...
Freeing initrd memory: 3955k freed
Simple Boot Flag at 0x35 set to 0x1
HugeTLB registered 4 MB page size, pre-allocated 0 pages
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
msgmni has been set to 625
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
Non-volatile memory driver v1.3
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
serial 00:0b: activated
00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial 0000:00:0a.1: PCI INT A -> Link[LNKC] -> GSI 9 (level, low) -> IRQ 9
e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
e100: Copyright(c) 1999-2006 Intel Corporation
e100 0000:00:0a.0: PCI INT A -> Link[LNKC] -> GSI 9 (level, low) -> IRQ 9
e100 0000:00:0a.0: PME# disabled
e100: eth0: e100_probe: addr 0xf4010000, irq 9, MAC addr 00:90:27:96:b1:d0
console [netcon0] enabled
netconsole: network logging started
PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
rtc_cmos 00:06: RTC can wake from S4
rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, y3k, 242 bytes nvram
cpuidle: using governor ladder
cpuidle: using governor menu
TCP cubic registered
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
NET: Registered protocol family 17
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
rtc_cmos 00:06: setting system clock to 2010-02-14 15:09:23 UTC (1266160163)
Freeing unused kernel memory: 272k freed
Write protecting the kernel text: 2388k
Write protecting the kernel read-only data: 728k
thermal LNXTHERM:01: registered as thermal_zone0
ACPI: Thermal Zone [THM0] (48 C)
Linux agpgart interface v0.103
SCSI subsystem initialized
Floppy drive(s): fd0 is 1.44M
agpgart-intel 0000:00:00.0: Intel 440BX Chipset
agpgart-intel 0000:00:00.0: AGP aperture is 64M @ 0xf8000000
ohci1394 0000:02:00.0: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
uhci_hcd: USB Universal Host Controller Interface driver
libata version 3.00 loaded.
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
uhci_hcd 0000:00:07.2: PCI INT D -> Link[LNKD] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:07.2: UHCI Host Controller
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:07.2: irq 11, io base 0x00001820
usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: UHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.33-rc8 uhci_hcd
usb usb1: SerialNumber: 0000:00:07.2
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[11] MMIO=[f6000000-f60007ff] Max Packet=[2048] IR/IT contexts=[4/8]
pata_cmd64x 0000:02:01.0: PCI INT A -> Link[LNKB] -> GSI 11 (level, low) -> IRQ 11
scsi0 : pata_cmd64x
scsi1 : pata_cmd64x
ata1: PATA max UDMA/66 cmd 0x30a0 ctl 0x3094 bmdma 0x3080 irq 11
ata2: PATA max UDMA/66 cmd 0x3098 ctl 0x3090 bmdma 0x3088 irq 11
pata_cmd64x: active 10 recovery 10 setup 3.
pata_cmd64x: active 10 recovery 10 setup 3.
ata_piix 0000:00:07.1: version 2.13
scsi2 : ata_piix
scsi3 : ata_piix
ata3: PATA max UDMA/33 cmd 0x1f0 ctl 0x3f6 bmdma 0x1800 irq 14
ata4: PATA max UDMA/33 cmd 0x170 ctl 0x376 bmdma 0x1808 irq 15
pata_cmd64x: active 10 recovery 10 setup 3.
pata_cmd64x: active 10 recovery 10 setup 3.
ata3.00: ATA-5: IC25N020ATCS04-0, CA2OA71A, max UDMA/100
ata3.00: 39070080 sectors, multi 16: LBA
ata3.00: configured for UDMA/33
usb 1-1: new full speed USB device using uhci_hcd and address 2
scsi 2:0:0:0: Direct-Access ATA IC25N020ATCS04-0 CA2O PQ: 0 ANSI: 5
sd 2:0:0:0: [sda] 39070080 512-byte logical blocks: (20.0 GB/18.6 GiB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2
sd 2:0:0:0: [sda] Attached SCSI disk
usb 1-1: New USB device found, idVendor=0451, idProduct=2036
usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
usb 1-1: Product: General Purpose USB Hub
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 2 ports detected
usb 1-1.1: new full speed USB device using uhci_hcd and address 3
usb 1-1.1: New USB device found, idVendor=03eb, idProduct=3312
usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
hub 1-1.1:1.0: USB hub found
hub 1-1.1:1.0: 4 ports detected
ieee1394: Host added: ID:BUS[0-00:1023] GUID[0011060000004434]
floppy0: no floppy controllers found
Floppy drive(s): fd0 is 1.44M
floppy0: no floppy controllers found
PM: Starting manual resume from disk
kjournald starting. Commit interval 5 seconds
EXT3-fs (sda1): mounted filesystem with writeback data mode
udev: starting version 150
input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input1
Marking TSC unstable due to TSC halts in idle
Switching to clocksource acpi_pm
ACPI: Lid Switch [LID]
input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input2
ACPI: Sleep Button [SLPB]
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
ACPI: Power Button [PWRF]
ACPI: AC Adapter [AC] (on-line)
ACPI: Battery Slot [BAT0] (battery present)
Floppy drive(s): fd0 is 1.44M
parport_pc 00:0c: activated
parport_pc 00:0c: reported by Plug and Play ACPI
parport0: PC-style at 0x3bc (0x7bc), irq 7, dma 1 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
yenta_cardbus 0000:00:08.0: CardBus bridge found [1014:0185]
yenta_cardbus 0000:00:08.0: ISA IRQ mask 0x0438, PCI irq 11
yenta_cardbus 0000:00:08.0: Socket status: 30000006
yenta_cardbus 0000:00:08.1: CardBus bridge found [1014:0185]
yenta_cardbus 0000:00:08.1: ISA IRQ mask 0x0438, PCI irq 11
yenta_cardbus 0000:00:08.1: Socket status: 30000006
IBM TrackPoint firmware: 0x0e, buttons: 3/3
input: TPPS/2 IBM TrackPoint as /devices/platform/i8042/serio1/input/input4
yenta_cardbus 0000:02:02.0: CardBus bridge found [1014:0148]
yenta_cardbus 0000:02:02.0: Using INTVAL to route CSC interrupts to PCI
yenta_cardbus 0000:02:02.0: Routing CardBus interrupts to PCI
yenta_cardbus 0000:02:02.0: TI: mfunc 0x00001002, devctl 0x66
irq 11: nobody cared (try booting with the "irqpoll" option)
Pid: 689, comm: modprobe Not tainted 2.6.33-rc8 #1
Call Trace:
[<c12518be>] ? printk+0x18/0x1a
[<c104b7d7>] __report_bad_irq+0x27/0x90
[<c104b999>] note_interrupt+0x159/0x190
[<c103bf66>] ? clockevents_program_event+0x86/0x140
[<c104c0bb>] handle_level_irq+0x8b/0xc0
[<c100480e>] handle_irq+0x7e/0x90
[<c100442a>] do_IRQ+0x3a/0xa0
[<c103c7b7>] ? tick_program_event+0x17/0x20
[<c1034087>] ? hrtimer_interrupt+0x177/0x280
[<c104c030>] ? handle_level_irq+0x0/0xc0
[<c10031f0>] common_interrupt+0x30/0x38
[<c104c030>] ? handle_level_irq+0x0/0xc0
[<c104a7e7>] ? handle_IRQ_event+0x17/0xd0
[<c104c030>] ? handle_level_irq+0x0/0xc0
[<c104c07a>] handle_level_irq+0x4a/0xc0
<IRQ> [<c100442a>] ? do_IRQ+0x3a/0xa0
[<c104ae0c>] ? __enable_irq+0x7c/0x90
[<c10031f0>] ? common_interrupt+0x30/0x38
[<d4c08083>] ? yenta_probe_cb_irq+0x93/0x120 [yenta_socket]
[<d4c0839a>] ? ti12xx_override+0x28a/0x760 [yenta_socket]
[<d4c08e5c>] ? yenta_probe+0x345/0x75a [yenta_socket]
[<c111641e>] ? local_pci_probe+0xe/0x10
[<c11170d0>] ? pci_device_probe+0x60/0x80
[<c1179861>] ? driver_probe_device+0x81/0x180
[<c11163fb>] ? pci_match_device+0x9b/0xb0
[<c11799e9>] ? __driver_attach+0x89/0x90
[<c1179108>] ? bus_for_each_dev+0x48/0x70
[<c11796f9>] ? driver_attach+0x19/0x20
[<c1179960>] ? __driver_attach+0x0/0x90
[<c1178b2f>] ? bus_add_driver+0x19f/0x260
[<c1116420>] ? pci_device_shutdown+0x0/0x20
[<c1116420>] ? pci_device_shutdown+0x0/0x20
[<c1179c85>] ? driver_register+0x65/0x120
[<c11172c9>] ? __pci_register_driver+0x39/0xb0
[<d4c0d017>] ? yenta_socket_init+0x17/0x19 [yenta_socket]
[<c100111d>] ? do_one_initcall+0x2d/0x180
[<d4c0d000>] ? yenta_socket_init+0x0/0x19 [yenta_socket]
[<c104472f>] ? sys_init_module+0xaf/0x210
[<c1002cd7>] ? sysenter_do_call+0x12/0x26
handlers:
[<d4969940>] (usb_hcd_irq+0x0/0x60 [usbcore])
[<d484a090>] (ohci_irq_handler+0x0/0x850 [ohci1394])
[<d491bac0>] (ata_sff_interrupt+0x0/0xe0 [libata])
[<d4c08930>] (yenta_interrupt+0x0/0xd0 [yenta_socket])
[<d4c08930>] (yenta_interrupt+0x0/0xd0 [yenta_socket])
Disabling IRQ #11
yenta_cardbus 0000:02:02.0: ISA IRQ mask 0x0438, PCI irq 9
yenta_cardbus 0000:02:02.0: Socket status: 30000006
yenta_cardbus 0000:02:02.0: pcmcia: parent PCI bridge I/O window: 0x4000 - 0x4fff
yenta_cardbus 0000:02:02.0: pcmcia: parent PCI bridge Memory window: 0x14000000 - 0x1bffffff
yenta_cardbus 0000:02:02.0: pcmcia: parent PCI bridge Memory window: 0x1c000000 - 0x23ffffff
yenta_cardbus 0000:02:02.1: CardBus bridge found [1014:0148]
yenta_cardbus 0000:02:02.1: Using INTVAL to route CSC interrupts to PCI
yenta_cardbus 0000:02:02.1: Routing CardBus interrupts to PCI
yenta_cardbus 0000:02:02.1: TI: mfunc 0x00001002, devctl 0x66
floppy0: no floppy controllers found
yenta_cardbus 0000:02:02.1: ISA IRQ mask 0x0438, PCI irq 9
yenta_cardbus 0000:02:02.1: Socket status: 30000006
yenta_cardbus 0000:02:02.1: pcmcia: parent PCI bridge I/O window: 0x4000 - 0x4fff
yenta_cardbus 0000:02:02.1: pcmcia: parent PCI bridge Memory window: 0x14000000 - 0x1bffffff
yenta_cardbus 0000:02:02.1: pcmcia: parent PCI bridge Memory window: 0x1c000000 - 0x23ffffff
thinkpad_acpi: ThinkPad ACPI Extras v0.24
thinkpad_acpi: http://ibm-acpi.sf.net/
thinkpad_acpi: ThinkPad BIOS IZET9BWW (2.23 ), EC unknown
thinkpad_acpi: WARNING: Outdated ThinkPad BIOS/EC firmware
thinkpad_acpi: WARNING: This firmware may be missing critical bug fixes and/or important features
Registered led device: tpacpi::thinklight
Registered led device: tpacpi::power
Registered led device: tpacpi::standby
thinkpad_acpi: Console audio control enabled, mode: monitor (read only)
input: ThinkPad Extra Buttons as /devices/platform/thinkpad_acpi/input/input5
CS4281 0000:00:0b.0: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
gameport: CS4281 Gameport is pci0000:00:0b.0/gameport0, speed 2294kHz
Adding 680392k swap on /dev/sda2. Priority:-1 extents:1 across:680392k
EXT3-fs (sda1): using internal journal
fuse init (API version 7.13)
e100 0000:00:0a.0: firmware: using built-in firmware e100/d101s_ucode.bin
ADDRCONF(NETDEV_UP): eth0: link is not ready
e100: eth0 NIC Link is Up 100 Mbps Full Duplex
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
input: ACPI Virtual Keyboard Device as /devices/virtual/input/input6
thinkpad_acpi: asked for hotkey mask 0x0006080c, but firmware forced it to 0x0000080c
input: /usr/sbin/thinkpad-keys as /devices/virtual/input/input7
ADDRCONF(NETDEV_UP): eth0: link is not ready
e100: eth0 NIC Link is Up 100 Mbps Full Duplex
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Bluetooth: Core ver 2.15
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.14
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM ver 1.11
Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Bluetooth: BNEP filters: protocol multicast
Bridge firewalling registered
Bluetooth: SCO (Voice Link) ver 0.6
Bluetooth: SCO socket layer initialized
lp0: using parport0 (interrupt-driven).

00:00.0 Host bridge [0600]: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX Host bridge [8086:7190] (rev 03)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 64
Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
Capabilities: <access denied>
Kernel driver in use: agpgart-intel

00:01.0 PCI bridge [0604]: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge [8086:7191] (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 128
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 00002000-00002fff
Memory behind bridge: f4100000-f5ffffff
Prefetchable memory behind bridge: 34000000-340fffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B+
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-

00:04.0 PCI bridge [0604]: Texas Instruments PCI2032 PCI Docking Bridge [104c:ac22] (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 32 bytes
Bus: primary=00, secondary=02, subordinate=08, sec-latency=68
I/O behind bridge: 00004000-00004fff
Memory behind bridge: 14000000-1bffffff
Prefetchable memory behind bridge: 1c000000-23ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>

00:07.0 Bridge [0680]: Intel Corporation 82371AB/EB/MB PIIX4 ISA [8086:7110] (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0

00:07.1 IDE interface [0101]: Intel Corporation 82371AB/EB/MB PIIX4 IDE [8086:7111] (rev 01) (prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1]
Region 4: I/O ports at 1800 [size=16]
Kernel driver in use: ata_piix

00:07.2 USB Controller [0c03]: Intel Corporation 82371AB/EB/MB PIIX4 USB [8086:7112] (rev 01) (prog-if 00 [UHCI])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at 1820 [size=32]
Kernel driver in use: uhci_hcd

00:07.3 Bridge [0680]: Intel Corporation 82371AB/EB/MB PIIX4 ACPI [8086:7113] (rev 03)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin ? routed to IRQ 9

00:08.0 CardBus bridge [0607]: Ricoh Co Ltd RL5c476 II [1180:0476] (rev 80)
Subsystem: IBM ThinkPad A/T/X Series [1014:0185]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 50000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=09, subordinate=0c, sec-latency=176
Memory window 0: 24000000-27fff000 (prefetchable)
Memory window 1: 28000000-2bfff000
I/O window 0: 00001400-000014ff
I/O window 1: 00001c00-00001cff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
Kernel driver in use: yenta_cardbus

00:08.1 CardBus bridge [0607]: Ricoh Co Ltd RL5c476 II [1180:0476] (rev 80)
Subsystem: IBM ThinkPad A/T/X Series [1014:0185]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168
Interrupt: pin B routed to IRQ 11
Region 0: Memory at 50100000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=0d, subordinate=10, sec-latency=176
Memory window 0: 2c000000-2ffff000 (prefetchable)
Memory window 1: 30000000-33fff000
I/O window 0: 00003400-000034ff
I/O window 1: 00003800-000038ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
Kernel driver in use: yenta_cardbus

00:0a.0 Ethernet controller [0200]: Intel Corporation 82557/8/9/0/1 Ethernet Pro 100 [8086:1229] (rev 09)
Subsystem: Intel Corporation EtherExpress PRO/100+ MiniPCI [8086:2408]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 66 (2000ns min, 14000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 9
Region 0: Memory at f4010000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at 1840 [size=64]
Region 2: Memory at f4020000 (32-bit, non-prefetchable) [size=128K]
[virtual] Expansion ROM at 34100000 [disabled] [size=1M]
Capabilities: <access denied>
Kernel driver in use: e100

00:0a.1 Serial controller [0700]: Xircom Mini-PCI V.90 56k Modem [115d:000c] (prog-if 02 [16550])
Subsystem: Intel Corporation Device [8086:2408]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 9
Region 0: I/O ports at 1810 [size=8]
Region 1: Memory at f4011000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: serial

00:0b.0 Multimedia audio controller [0401]: Cirrus Logic Crystal CS4281 PCI Audio [1013:6005] (rev 01)
Subsystem: IBM Device [1014:0183]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (1000ns min, 6000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f4012000 (32-bit, non-prefetchable) [size=4K]
Region 1: Memory at f4000000 (32-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel driver in use: CS4281

01:00.0 VGA compatible controller [0300]: ATI Technologies Inc Rage Mobility P/M AGP 2x [1002:4c4d] (rev 64) (prog-if 00 [VGA controller])
Subsystem: IBM Device [1014:0182]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 66 (2000ns min), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f5000000 (32-bit, non-prefetchable) [size=16M]
Region 1: I/O ports at 2000 [size=256]
Region 2: Memory at f4100000 (32-bit, non-prefetchable) [size=4K]
[virtual] Expansion ROM at 34000000 [disabled] [size=128K]
Capabilities: <access denied>

02:00.0 FireWire (IEEE 1394) [0c00]: VIA Technologies, Inc. VT6306/7/8 [Fire II(M)] IEEE 1394 OHCI Controller [1106:3044] (rev 46) (prog-if 10 [OHCI])
Subsystem: VIA Technologies, Inc. VT6306/7/8 [Fire II(M)] IEEE 1394 OHCI Controller [1106:3044]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (8000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f6000000 (32-bit, non-prefetchable) [size=2K]
Region 1: I/O ports at 3000 [size=128]
Capabilities: <access denied>
Kernel driver in use: ohci1394

02:01.0 IDE interface [0101]: Silicon Image, Inc. PCI0648 [1095:0648] (rev 01) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: Silicon Image, Inc. PCI0648 [1095:0648]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (500ns min, 1000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 30a0 [size=8]
Region 1: I/O ports at 3094 [size=4]
Region 2: I/O ports at 3098 [size=8]
Region 3: I/O ports at 3090 [size=4]
Region 4: I/O ports at 3080 [size=16]
Capabilities: <access denied>
Kernel driver in use: pata_cmd64x

02:02.0 CardBus bridge [0607]: Texas Instruments PCI1420 PC card Cardbus Controller [104c:ac51]
Subsystem: IBM ThinkPad A20m [1014:0148]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 9
Region 0: Memory at 52000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
Memory window 0: 1c000000-1ffff000 (prefetchable)
Memory window 1: 14000000-17fff000
I/O window 0: 00004000-000040ff
I/O window 1: 00004400-000044ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
Kernel driver in use: yenta_cardbus

02:02.1 CardBus bridge [0607]: Texas Instruments PCI1420 PC card Cardbus Controller [104c:ac51]
Subsystem: IBM ThinkPad A20m [1014:0148]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 9
Region 0: Memory at 53000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=07, subordinate=07, sec-latency=176
Memory window 0: 20000000-23fff000 (prefetchable)
Memory window 1: 18000000-1bfff000
I/O window 0: 00004800-000048ff
I/O window 1: 00004c00-00004cff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
Kernel driver in use: yenta_cardbus


--
Meelis Roos (mroos@ut.ee) http://www.cs.ut.ee/~mroos/


\
 
 \ /
  Last update: 2010-02-14 17:03    [W:1.166 / U:1.184 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site